Instruction/ maintenance manual of the product FT-8001 A Toshiba
Go to page of 20
.
1 IMPORT ANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions.
2 13. Do not use the telephone in the vicinity of a gas leak. CAUTION: TO REDUCE THE RISK OF FIRE OR INJUR Y TO PERSONS BY THE BA TTERY , READ AND FOLLOW THESE INSTRUCTIONS. 1. Use only the appropriate type and size battery pack specified in the instruction manual provided for this product.
3 SER VICE REQUIREMENTS If the cordless telephone should malfunction, or need changes or modifications, all repairs will be performed by an authorized T oshiba Service Station. This unit has been registered with the FCC for direct connection to the telephone network.
4 INTRODUCTION T oshiba America Consumer Products, Inc. takes pride in presenting your phone, one of the finest cordless telephones available. Intelligent design, superb craftsmanship, and the latest .
5 INST ALLA TION 1. SETTING UP THE BASE UNIT For use on a desk or counter top follow the instructions below . DESKTOP MOUNTING: • USE ONL Y WITH Supplied AC ADAPTOR (T AC-8001); power source AC 120V , 60Hz/DC 9V). • The AC adaptor must remain connected at all times.
6 Red Black 2. CHARGE THE BA TTER Y P ACK Note Use only the supplied battery pack (TRB-8000 power source 600 mAh, 3.6V). q Remove the battery compartment cover on the back of the handset by sliding it down. w Plug the battery pack cord into the connector in the battery compartment by observing the correct polarity .
7 After the battery pack is fully charged; Operation Approx. battery life While in use (T alk mode) up to 7 hours While not in use (Standby mode) up to 14 days When T ALK/BA TT LOW LED blinks, all handset buttons are disabled and the battery needs to be charged.
8 Wall mount template IMPORTANT: Before mounting, select a wall area of sufficient strength. If mounting on wallboard or in an area of questionable strength, locate a stud for maximum support of your telephone. Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard.
9 LOCA TIONS OF CONTROLS HANDSET CONTROLS BASE UNIT CONTROLS Antenna Charging Contacts RDL/P (Redial/Pause) button DC IN 9V jack LINE Modular jack Antenna PAGE button Charging Contacts IN USE/CHARGE LED Speed Dial Index Card (back) Write down numbers stored in memory .
10 Please see “LOCA TION OF CONTROLS” for the location of each button used for the following operations. SETTING THE DIAL MODE Most phone systems use tone dialing. But, to use tone dialing, you must have a tone service dialing system supplied by your telephone company .
11 MAKING A CALL 1. MAKING A CALL q Press TALK . The T ALK/BA TT LOW LED will light. w Listen for the dialtone. e Key in the phone number you are calling. r T o hang up, press TALK again or place the handset on the base unit. The T ALK/BA TT LOW LED turns off.
12 3. INTERFERENCE OR ST A TIC If you hear noise during a call, press CH to select another channel. The T ALK/BA TT LOW LED blinks while changing a channel. 4. CHANGING THE RINGER VOLUME Press VOL/RING to select one of four ringer tone and volume combinations during standby mode.
13 8. SENDING TONE SIGNAL (for Pulse service user) Even if you have Pulse service (the dial mode is set to Pulse), you can use this phone with banking and other phone services requiring touch tone signals. q Dial the service number and wait for the connection.
14 MEMOR Y DIALING Y ou can store up to 10 telephone numbers in memory . Notes In memory dialing operation, • If more than 20 seconds elapse between pressing buttons, the operation will be cancelled and you must start over again. • If you press a wrong button, an error tone sounds and the handset returns to standby mode.
15 Replacing a telephone number Just store the new number following the same steps in “ 1. ST ORING NUMBERS. ” The new number will replace the previously stored one. 2. DIALING A ST ORED NUMBER q Pick up the handset and press TALK . The T ALK/BA TT LOW LED lights.
16 ACCESSORIES Rechargeable Battery pack (1) TRB-8000 Part # RC004931 AC Adaptor (1) T AC-8001 Part # RC009790 for FT -8001 T AC-8001 Part # RC009791 for FT -8001W T elephone Cord (1) Part # RC008231 .
17 TROUBLESHOOTING GUIDE Should any problem occur with the set, make the following simple tests to determine whether or not servicing is required. PROBLEM The handset battery does not charge. Battery becomes low quickly . Can not make or receive calls.
PROBLEM The handset does not ring or receive a page. CHARGE LED does not light when the handset is placed on the base. Noise or interference. The unit does not operate properly . When the handset is returned to the base unit with the volume level set at High, a momentary squeal or howling sound may sometimes be heard.
UCZZ01337BZ RC012151 Printed in China © 2001 TOSHIBA AMERICA CONSUMER PRODUCTS. INC. All warranties implied by state law , including the implied warranties of merchantability and fitness for a particular purpose, are expressly limited to the dura tion of the limited warranties set forth above.
An important point after buying a device Toshiba FT-8001 A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba FT-8001 A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba FT-8001 A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba FT-8001 A you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba FT-8001 A will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba FT-8001 A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba FT-8001 A.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba FT-8001 A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba FT-8001 A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
