Instruction/ maintenance manual of the product P3150 Acer
Go to page of 141
SER VICE MANUAL Prepared: Checked: Approved: Date Revise V ersion Description 2008.4.10 V1.0 Initial Issue 2008.5.28 V2.0 Add Marketing Spec in Chapter 1 2008.7.22 V3.0 Add P3150 Refresh/P3250 Refresh 2008.10.10 V4.0 Add W aveform Download in Ch5 modify Ch4, Ch6 and AppendixB 2010.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential I Comparison List P ART P3251 P3150 P3150 refresh P3250 P3250 refresh F AN 49.8FN01G001 49.89S01G001 ENGINE 70.8GC07GR01 70.89Y22GR01 PHOTO SENSOR BD 80.8GB04G001 80.88N04G001 COLOR WHEEL 70.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential II Preface This manual is applied to P3150/P3250/P3150 refresh/P3250 refresh/P3251 projection system. The manual gives you a brief description of basic technical information to help in service and maintain the product.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential III T able of Content Chapter 1 Introduction Highlight 1-1 Compatible Mode 1-4 Product Overview 1-6 Chapter 2 Disassembly Process Equipment .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential IV Re-write Lamp Usage Hour 2-19 Assemble IR Sensor Module 2-20 Assemble Interrupt Switch Module 2-20 Assemble Speaker Module 2-21 Assemble .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential V OSD Reset 4-1 T est Condition 4-2 T est Inspection Procedure 4-4 PC Mode 4-4 Video Performance 4-7 Optical Performance Measure 4-9 SD Card.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential VI Chapter 6 EDID Upgrade EDID Introduction 6-1 Equipment Needed 6-2 Setup Procedure 6-3 EDID Key-In Procedure 6-3 Setup Procedure (HDMI) 6-.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-1 Chapter 1 Introduction 1-1 Highlight No Item Description 1 Dimensions (WxDxH) - 209 x 74.2 x 172.2 mm (for P3150/P3250/P3150 Refresh/ P3250 Refresh) - 209 x 64 x 164mm (for P3251) 2 Weight - 1.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-2 No Item Description 12 Throw Distance - 1.0m – 12m 13 Throw Ratio - 1.95 – 2.15:1 @ 60” 14 Input signal spec - Video Signal RGB (PC) ● Analog RGB 0.7Vp-p, 75 ohm, Separate TTL H,V Sync ● Analog RGB 1Vp-p, 75 ohm, Sync.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-3 No Item Description 17 Contrast P3150/P3250/P3150 refresh/P3250 refresh : - Engineering Spec: ● 1400 : 1 Full White and Black (Minimum.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-4 1-2 Compatible Mode A. Analog (for P3150/P3250/P3150 Refresh/P3250 Refresh) Compatibility Resolution V -Sync [Hz] H-Sync [KHz] VGA 640x480 60 31.50 640x480 72 37.90 640x480 75 37.50 720x400 70 31.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-5 Compatibility Resolution V -Sync [Hz] H-Sync [KHz] VGA 640x480 60 31.50 640x480 72 37.90 640x480 75 37.50 720x400 70 31.50 SVGA 800x600 56 35.20 800x600 60 37.90 800x600 72 48.10 800x600 75 46.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-6 1-3 Product Overview Projector Outlook (P3150) Front /Upper side Item Description Item Description 1 Zoom Lever 6 Elevator button 2 Focu.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-7 Rear side (for P3150/P3250/P3150 Refresh/P3250 Refresh) Item Description Item Description 1 USB connector 5 S-V ideo input connector 2 P.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-8 Rear side (for P3251) Item Description Item Description 1 SD Card reader 6 S-Video input connector 2 USB A connector 7 Audio input conne.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-9 Control Panel Item Function Description 1 LAMP Lamp Indicator LED 2 TEMP T emp Indicator LED 3 SOURCE Press “SOURCE” to choose RGB, S-Video,Composite and HDMI™ sources. 4 Empowering key Unique Acer functions: eOpening, eView ,eT imer .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-10 Remote Control Layout (for P3150/P3250/P3150 Refresh/P3250 Refresh).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-1 1 Item Icon Function Description 1 Infrared transmitter Sends signals to the projector . 2 Laser pointer Aim the remote at the viewing screen 3 FREEZE T o pause the screen image. 4 HIDE Momentarily turns off the video.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-12 Item Icon Function Description 26 WIRELESS Press “WIRELESS” to display the image which is wirelessly transmitted from the PC to the projector via the “Acer eProjection Management” utility .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-13 Item Icon Function Description 1 Infrared transmitter Sends signals to the projector . 2# Laser pointer Aim the remote at the viewing screen 3 FREEZE T o pause the screen image. 4 HIDE Momentarily turns off the video.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-14 Item Icon Function Description 24 * HDMI™/DVI Press “HDMI™/DVI” to change source to HDMI™. 25 USB B No USB B function. 26 LAN/WiFi No LAN/WiFi function. 27 KeyPad 0~9 Press “0~9” to input a password in the “Security settings”.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-15 Connecting the Projector Item Description Item Description 1 Power cord 5 Audio cable Jack/Jack 2 USB cable 6 HDMI cable 3 VGA cable 7 .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-16 System Block Diagram.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1-17 Bottom Cover Dimension.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-1 Chapter 2 Disassembly& Assembly Process 2-1 Equipment Needed & Product Overview 1. Screw Bit (+) :107 2. Hex Sleeves 5mm 3. Long Nose Nipper 4. Screw Bit (+) :102 5. Hex Sleeves 7mm 6.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-2 2-2 Disassemble Lamp Cover Module 1. T urn over the projector 2. Unscrew 2 screws (as red circle) 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-3 2-3 Disassemble Lamp Module 1. Unscrew 2 screws (as red circle) 2. Disassemble Lamp Module.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-4 2-4 Disassemble T op Cover Module 1. Unscrew 5 screws (as red circle) 2. Unscrew 2 Hex screws (as yellow circle) 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-5 2-5 Disassemble Key Pad Board Module 1. Unscrew 4 screws (as red circle) 2. Separate Key Pad Button and Key Pad Board 2-6 Disassemble Zoom Ring Module 1. Unscrew 3 screws (as yellow circle) 2.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-6 2-7 Disassemble Main Board Module 1. T ear off 2 Mylars (as red square) 2. Unplug 5 connectors (as green square) 3. Push Main Board Module (as red arrow) to unplug 1 connector (as yellow square) 4.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-7 5. Disassemble Main Board Module 6. Unscrew 2 screws(as red circle) to disassemble the Daughter Board.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-8 A A 2-8 Disassemble Color Wheel Module 1. Unscrew 2 screws (as red circle) 2. Disassemble Color Wheel Module 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-9 2-9 Disassemble Front Cover Module 1. Release 6 tenons (as red circle) 2. Push the front cover forward to disassemble front cover module.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-10 2-10 Disassemble Ballast Module 1. Unplug 2 cables (as red square) 2. Unscrew 3 screws (as red circle) 3. Disassemble AC Inlet Bracket 4. Unscrew 3 screws (as yellow circle) 5. Disassemble Ballast Module 6.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-1 1 2-1 1 Disassemble DC-DC Module 1. Unscrew 1 screw (as red circle) 2. Disassemble DC-DC Module 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-12 2-12 Disassemble Thermal Switch Module 1. Unscrew 1 screw (as red circle) 2. Disassemble Thermal Switch.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-13 2-13 Disassemble Lamp Blower Module and System Fan Module 1. Unscrew 4 screws (as red circle) 2. Disassemble Lamp Blower Module and System Fan Module 3. Unscrew 3 screws (as yellow circle) 4.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-14 2-14 Disassemble Lamp to Ballast Cable 1. Unscrew 1 screw (as red circle) 2. Unplug Lamp to Ballast Cable.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-15 2-15 Disassemble Engine Module 1. Unscrew 4 screws (as red circle) 2. Disassemble Engine Module 3. Unscrew 3 screws (as yellow circle) 4. Disassemble Focus Ring 2-16 Disassemble DMD Board and DMD Chip 1.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-16 2-17 Disassemble Speaker Module 1. Disassemble Speaker Module 2. Separate Speaker and Rubber 2-18 Disassemble Interrupt Switch Module 1. Unscrew 1 screw (as red circle) 2. Release 2 tenons (as yellow circle) 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-17 2-19 Disassemble IR Sensor Module 1. T ear off 1 Mylar (as red square) 2. Disassemble IR Sensor Board.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-18 2-20 Rod Adjustment 1. Environment adjustment - The distance between the engine and the screen is 2.36 M - This process should be done at a dark environment. (under 5 Lux) 2. Procedure adjustment - Change the screen to “white screen.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-19 2-21 Re-write Lamp Usage Hour 1. Get into service mode - Press (power→left→left→menu) to get into service mode 2. Choose RD Menu 3. Choose Lamp life warning test 4. Use left or right key to re-write the lamp hour back to previous lamp usage hour 5.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-20 2-22 Assemble IR Sensor Module 1. Assemble IR Sensor Board in red square 2. Stick 1 Mylar .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-21 2-24 Assemble Speaker Module 1. Assemble Speaker and Rubber 2. Assemble Speaker Module.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-22 2-26 Assemble Engine Module 1. Assemble Focus Ring 2. Screw 3 screws (as yellow circle) 3. Assemble Engine Module 4. Screw 4 screws (as red circle) 2-25 Assemble DMD Board and DMD Chip 1.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-23 2-27 Assemble Lamp to Ballast Cable 1. Plug Lamp to Ballast Cable in yellow square 2. Screw 1 screw (as red circle).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-24 2-28 Assemble Lamp Blower Module and Syst em Fan Module 1. Assemble System Fan and Lamp Housing 2. Screw 3 screws (as green circle) 3. Stick 1 mylar (as red square) 4. Assemble Lamp Blower , Lamp Blower Duct and Lamp Blower Holder 5.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-25 2-29 Assemble Thermal Switch Module 1. Assemble Thermal Switch 2. Screw 1 screw (as red circle).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-26 2-30 Assemble DC-DC Module 1. Plug 2 cables in red square 2. Assemble DC-DC Module 3.Screw 1 screw (as red circle).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-27 2-31 Assemble Ballast Module 1. Stick 1 mylar under Ballast Module 2. Assemble Ballast Module 3. Screw 3 screws (as yellow circle) 4. Assemble AC Inlet Bracket 5.Screw 3 screws (as red circle) 6.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-28 D C B A A D C B 2-32 Assemble Front Cover Module 1. Assemble Front Cover Module Note: there are 6 tenons (as red circle).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-29 A A 2-33 Assemble Color Wheel Module 1. Assemble Photo Sensor Board 2. Screw 1 screw (as yellow circle) 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-30 2-34 Assemble Main Board Module 1. Screw 2 screws (as red circle) to assemble the Daughter Board.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-31 4. Plug 5 connectors (as green square) Note: - The arrangement of cables are as follows: A: DC-DC 5 pin cable B: Ballast 5 pin cable C:.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-32 2-36 Assemble Key Pad Board Module 1. Assemble Key Pad Button and Key Pad Board on T op Cover Module 2.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-33 2-37 Assemble T op Cover Module 1. Plug 1 FPC cable (as red square) 2. Assemble T op cover Module 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-34 2-38 Assemb le L amp Modu le 1. Assemble Lamp Module 2. Screw 2 screws (as red circle).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2-35 2-39 Assemble Lamp Cover Module 1. Assemble Lamp Cover Module 2. Screw 2 screws (as red circle) 3.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-1 Chapter 3 T roubleshooting 3-1 LED Lighting Message Message Power LED Lamp LED T emp LED Plug-in Power Cord Flash Red (100ms) Flash Red (100ms) Flash Red (100ms) Standby Mode Red X X Power button ON Blue X X F/W Download Mode Red Red Red Lamp Ignited Flash Blue 0.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-2 (R) - RED (B) - BLUE (F) - FLASH (X) - OFF Message Power LED Lamp LED T emp LED Error for Fan Fail(On Event) Blue X Flash Red 0.5 second H(On), 0.5 second L(Off) Error for Fan Fail(On Standby) Red X Flash Red 0.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-3 Power on (as soon as power button pressed) So(0.3s) Power on (lamp lighting failed) 2 x {So(0.1s) – Off(0.1s)} per lighting failure 12s interval for each trial lighting. Max 4 times of trial Power on (lens cap was not opened, for the model with sliding lens cover only) 2 x {So(0.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-4 3-3 Main Procedure No Symptom Procedure 1 No Power • Ensure the Power Cord and AC Power Outlet are securely connected • Check Lamp C.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-5 No Symptom Procedure 3 No Image • Ensure the Signal Cable and Source work (If you connect multiple sources at the same time, use the .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-6 No Symptom Procedure 7 Image Flicker • Do “Reset (All data)” of the OSD Menu • Ensure that the signal cables and source are work.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-7 No Symptom Procedure 13 Function Abnormal • Do “Reset (All data)” of the OSD Menu • Check Main Board • Check DMD Board 14 Audi.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3-8 No Symptom Procedure 17 SD Card/ USB ash disk Function Failed • Ensure that the signal cables and source work as well.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-1 Chapter 4 Function T est & Alignment Procedure 4-1 T est Equipment Needed - IBM PC with SVGA/XGA resolution - DVD player with Multi-system (NTSC/P AL/SECAM), equipped “Component”, “S-Video” , “Composite” and "HDMI".
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-2 4-4 T est Condition - Circumstance brightness: Dark room less than 5.0 lux. - Inspection distance: 1.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-3 Defect specication table Order Symptom Pattern Criteria 1 Bright pixel (dots) Gray 10 pattern A+B≤1 2 Dark pixel (dots) White patte.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-4 4-5 T est Inspection Procedure Change parts/ Update M/B FW Color Wheel Lamp Module Engine EDID Lamp Driver V ersion Update v v v Colo r .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-5 - Adjust Resync or Frequency/T racking/H. Posi - tion/V . Position to the inner screen. Inspection item - Eliminate visul wavy noise by Rsync, Frequency or T racking selction. - Check if there is noise on the screen.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-6 4. �right �lemish �right �lemish Procedure - T est equipment: video generator - T est signal: analog 1024 x 768@60Hz - T est Pattern: Gray 15 Inspection item - Bright blemish check.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-7 7. Color performance Procedure - T est equipment: video generator . - T est signal: 480p, 720p, 1080p - T est Pattern: Master , 64 gray RGBW or SMPTE bar * Please refer to 4-2 to get into service mode.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-8 - Check the sound from speakers. 2. S-Video Procedure - T est equipment: DVD player - Test signal: S-Video Inspection item - Video performance test Inspection Distance - 1.8M ~2.5M Criteria - Check any abnormal color , line distortion or any noise on the screen.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-9 5.HDMI T est Procedure - T est Signal : 720p,1080i - T est Pattern : Any Pattern - Equipment: DVD Player with HDMI output - Display type must be set to 16:9 Inspection item - HDMI T est Criteria - Ensure if the image is well performed and the color can not discolor .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-10 2. �rightness Procedure - Full white pattern - Use CL100 to measure brightness values of P1~P9. - Follow the brightness formula to calculate brightness values. ☼ Brightness Formula Avg.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-1 1 4-9 SD Card /USB ash disk T est (only for P3251) 1.SD Card T est Procedure - T est equipment: SD Card(include test pattern), - T est Pattern: WhiteBlack,Graystep16, ColorBar - Turn on the projector and plug SD Card into the projector .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4-12 2. Check points for e�terior and print pattern Check item Check point T ext & Pattern Missing letters & pattern or blurry prints are unacceptable. Exterior Dirt, scrape, water ripples and uneven color are unacceptable.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-1 Chapter 5 Firmware Upgrade Section 1: System Firmware Upgrade 5-1 Equipment Needed Software : - DLP Composer - Firmware - 8M Flash (8M ash has to put in PC and set right path in 5-5 step4) Hardware : - Projector - Power cord (42.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-2 5-2 DLP Composer Lite Setup Procedure 1. Choose "DLP Composer Lite V7.1 Setup" Program. 2. Click Next button. 3. Read License Agreement. - Choose I accept and agree to be bound by all the terms and conditions of this License Agreement.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-3 6. Click Next. 7. Click Next. 8. Writing system registry values. 9. Click Finish..
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-4 5-3 USB Driver Upgrade Procedure 1. Set up - Plug in power cord and then press "Power" and "Menu" button simultaneou.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-5 5-4 Firmware Upgrade Procedure 1. Set-up - Plug in power cord and then press "Power" and "Menu" button simultaneousl.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-6 5. Select EditpreferencesCommunications - Choose USB". - Click OK". 6. Choose Flash Loader .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-7 7. Selete the item skip Boot Loader Area (select 32KB). - Click Reset Bus to erase the ash memory . 8. If the rmware i s ready , click start download to process the rmware upgrade.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-8 9. When rmware upgrade process is nished the unit return to stand-by status. The Power LED lights on Red. - Unplug USB cable and power cord and replug in power cord. 10. Restart the unit and enter the service mode to check the rmware version.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-9 Section 2 : W aveform Download 5-5 W aveform Download ( for refresh models) 1.Hold on the “Up” button, then plug Power Cord in, the Power LED lights on red. After about 5 seconds relea se “Up” button , Power LED turns to blue and T emp LED will ash for 4 seconds.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-10 5-6 W aveform Download ( for P3251) 1.Hold on the “Power” button, then plug Power Cord in, After about 4 seconds , release “Power” button, at the same time the Lamp LED ash red.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-1 1 Section 3 : Multi-Media Firmware Upgrade (only for P3251) 5-7 Equipment Needed Software : - 1201 tool - Firmware (*.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-12 5-8 USB Driver Upgrade Procedure 1. Set up - Hold on “Power” and "Menu" button and then Plug in power cord , hold on about 5 seconds, release "Power" and "Menu" button , the Power Lamp and T emp LED light RED at the same time.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-13 3) Click "Continue Anyway". 4) Click "Finish" to end the installation.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-14 5-9 Multi-Media Firmware Upgrade Procedure 1. Set-up - Hold on “Power” and "Menu" button and then Plug in power cord , hold on about 5 seconds, release "Power" and "Menu" button , the Power Lamp and T emp LED light RED at the same time.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-15 4. Click “Download.” 5. The success information will show on screen (as red square).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5-16 6. Restart the unit and enter the service mode to check the Multi-Media rmware version.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-1 Chapter 6 EDID Upgrade 6-1 EDID Introduction Extended Display Identication Data is a VESA standard data format that contains basic in.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-2 6-2 Equipment Needed Software - EDID Program (Generic V0.51) - EDID File Hardware - Projector - Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed) - Power cord for Projector (42.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-3 6-3 Setup Procedure (VGA) 1. Connect all ports (1) Connect P1 of Fixture with COM Port of PC/Laptop by RS232 Cable. (2) Connect P2 of Fixture with VGA port of Projector by VGA Cable. (3) Plug Power Adapter to Power CNN.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-4 6-4 EDID Key-In Procedure 1. Execute EDID Program (1) Click on "EDID" to execute EDID program. 2. Process (1) Check the COM port is COM 1" (Select the COM port which you are using).
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-5 5 6 7 5. Finish (1) "OK" will be shown on the screen. 6. Read EDID information (1) In the Read item,select "Analog" and "T rans". (2) Please press "Read" button.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-6 6-5 Setup Procedure (HDMI) 1. Connect all ports (1) Connect P1 of Fixture with COM Port of PC/Laptop by RS232 Cable. (2) Connect P2 of Fixture with P3 by DVI Cable. (3) Plug P4 to HDMI Port of the Projector .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-7 2. Process (1) Check the COM port is "COM 1" (Select the COM port which you are using). (2) Click the "Model" button. (3) Choose the source le "ACER_P3250_20080218_C.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-8 5. Finish (1) "OK" will be shown on the screen. 6. Read EDID information (1) In the Read item,select "Digital" and "T rans". (2) Please press "Read" button.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6-9 6-6 Default Language Reset (For P3150 refresh/P3250 refresh) (1) Hold on “Down” button then plug in the Power Cord. Note: At this moment, Power LED turns blue while T emp LED ashes in red for about 4s,then release the “Down” button.
P3150/P3250 /P3150 Refresh/P3250 Refresh/P3251 Condential 1 Appendix A DC. P3150 7 2 4 1 8 5 6 3 10 1 1 12.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 2 ITEM P/N DECRIPTION Supply 1 70.89Y03G001 ASSY BOTT OM COVER P3150 N 2 70.89Y01G001 ASSY TOP COVER MODULE P3150 N 3 70.89Y02G001 ASSY FRONT COVER P3150 N 4 70.89Y08G001 ASSY MAIN BOARD MODULE P3150 N 5 61.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 3 ASSY BLOWER 4510 MODULE 3 2 1 4 4 4 ITEM P/N DECRIPTION Supply 1 49.89S01G001 LAMP BLOWER / 45*45*10 mm, 60m 2 61.89S13G001 BLOWER 4510 HOLDER SECC M209X N 3 61.89S1 1G001 LAMP BLOWER 4510 DUCT AL M209X N 4 85.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 4 15 8 4 14 2 10 1 3 7 9 6 5 1 1 9 12 9 16 ASSY T OP COVER MODULE P3150.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 5 ITEM P/N DECRIPTION Supply 70.89Y25GR01 ASSY T OP COVER MODULE FOR P3150(SERVICE) 1 61.89Y02G001 TOP COVER P3150 N 2 42.89501G002 CABLE FPC 24P P=0.5 150mm KE 3 51.89Y04G001 TOP IR LENS P3150 N 4 51.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 6 ASSY FRONT COVER P3150 1 3 2 ITEM P/N DECRIPTION Supply 70.89Y24GR01 ASSY FRONT COVER MODULE FOR P3150/P3250(SERVICE) 1 51.89Y01G001 FRONT COVER P3150 N 2 51.89Y03G001 FRONT IR LENS P3150 N 3 61.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 7 ASSY BOTT OM COVER P3150 33 15 30 31 1 1 29 32 8 28 1 24 22 3 2 12 7 1 31 1 6 9 10 26 5 4 23 19 21 14 13 25 20 16 27 17 18 15.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 8 ITEM P/N DECRIPTION Supply 1 70.89Y17G001 ASSY LAMP HOUSING MODULE M209X N 2 70.89Y13G001 ASSY DC-DC MODULE P3150 N 3 70.89S09G001 ASSY BLOWER 4510 MODULE M209X N 4 51.89Y08G001 ELEV A T OR PUSH BUTTON P3150 5 51.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 9 ITEM P/N DECRIPTION Supply 70.89Y23GR01 ASSY PCBA MAIN BD MODULE FOR P3150(SERVICE) 1 80.89Y01G001 PCBA MAIN BOARD FOR P3150 N 2 41.82B17G001 EMI VIDEO GASKET N 3 41.82G03G001 EMI GASKET USB CONNECT OR EP719 N 4 41.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 10 3 6 5 3 2 4 1 ASSY DC-DC MODULE P3150 ITEM P/N DECRIPTION Supply 70.89Y28GR01 ASSY DC-DC MODULE FOR P3150/P3250 (SERVICE) 1 42.004A1G001 W .A.4P #24/#26 100mm DC.DC/BALLAST 2 42.004B1G001 W .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 1 1 ASSY LAMP HOUSING MODULE P3150 4 4 4 4 2 3 6 1 5 ITEM P/N DECRIPTION Supply 1 43.89S01G001 TH-RMAI SWITCH WITH BRACKET (KLIX- ON YSII 2 49.85M03G001 SYSTEM F AN/55*55*15mm 3 61.89Z06G001 LAMP HOUSING MG ALLOY EX330 N 4 85.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 12 ASSY SPEAKER MODULE P3150 ITEM P/N DECRIPTION Supply 1 49.89Y01G001 SPEAKER MINI IW 4 ohm 140 mm P3150 2 52.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 13 ASSY ENGINE MODULE P3150 6 9 8 18 17 16 5 20 21 2 7 23 24 15 1 15 13 10 15 15 1 1 14 3 19 12 24 4 24 25.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 14 ITEM P/N DECRIPTION Supply 70.89Y22GR01 ASSY ENGINE MODULE FOR P3150/ P3250(SERVICE) 1 70.89Y15G001 ASSY ENGINE BOTT OM COVER P3150 N 2 70.89Y05G001 ASSY ENGINE BASE MODULE P3150 N 3 70.89Y16G001 ASSY ROD MODULE P3150 N 4 70.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 15 1 1 10 6 7 9 8 5 1 4 3 2 AK. P3150 ITEM P/N DECRIPTION Supply 1 36.00006G031 W ARRANTY CARD ,EUROPE FOR ACER N 2 36.00027G001 SER VICE ST A TION CARD N 3 36.89Y01G001 USER’S GUIDE MUL TILINGUAL (C N 4 36.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 16 18 9 12 17 16 15 20 21 19 23 22 10 3 1 5 2 20 DP . P3150.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 17 ITEM P/N DECRIPTION Supply 1 51.00201G001 HANDLE BAR 1.PE HD70 N 2 51.00200G001 HANDLE BAR 2. PE HD70 N 3 55.89Y01G001 CART ON CARRY BOX P3150 N 4 55.89Y02G001 CENTER P APER BOX P3150 N 5 35.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 18 DC. P3250 7 2 4 1 8 5 6 3 10 1 1 12.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 19 ITEM P/N DECRIPTION Supply 1 70.89Y03G001 ASSY BOTT OM COVER P3150 N 2 70.89Y01G001 ASSY TOP COVER MODULE P3150 N 3 70.89Y02G001 ASSY FRONT COVER P3150 N 4 70.89Y08G001 ASSY MAIN BOARD MODULE P3150 N 5 61.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 20 ASSY BLOWER 4510 MODULE P3250 3 2 1 4 4 4 ITEM P/N DECRIPTION Supply 1 49.89S01G001 LAMP BLOWER / 45*45*10 mm, 60m 2 61.89S13G001 BLOWER 4510 HOLDER SECC M209X N 3 61.89S1 1G001 LAMP BLOWER 4510 DUCT AL M209X N 4 85.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 21 15 8 4 14 2 10 1 3 7 9 6 5 1 1 9 12 9 16 ASSY T OP COVER MODULE P3250.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 22 ITEM P/N DECRIPTION Supply 70.89Y30GR01 ASSY T OP COVER MODULE FOR P3250(SERVICE) 1 61.89Y02G001 TOP COVER P3150 N 2 42.89501G002 CABLE FPC 24P P=0.5 150mm KE 3 51.89Y04G001 TOP IR LENS P3150 N 4 51.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 23 ASSY FRONT COVER P3250 1 3 2 ITEM P/N DECRIPTION Supply 70.89Y24GR01 ASSY FRONT COVER MODULE FOR P3150/P3250(SERVICE) 1 51.89Y01G001 FRONT COVER P3150 N 2 51.89Y03G001 FRONT IR LENS P3150 N 3 61.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 24 ASSY BOTT OM COVER P3250 22 1 15 30 31 1 1 29 32 8 28 18 24 3 2 12 7 31 1 6 9 10 26 27 5 4 23 19 21 33 14 13 25 20 16 22 17 15.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 25 ITEM P/N DECRIPTION Supply 1 70.89Y17G001 ASSY LAMP HOUSING MODULE M209X N 2 70.89Y13G001 ASSY DC-DC MODULE P3150 N 3 70.89S09G001 ASSY BLOWER 4510 MODULE M209X N 4 51.89Y08G001 ELEV A T OR PUSH BUTTON P3150 5 51.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 26 26 ITEM P/N DECRIPTION Supply 70.89Y29GR01 ASSY PCBA MAIN BD MODULE FOR P3250(SERVICE) 1 80.89Y01G001 PCBA MAIN BOARD FOR P3150 N 2 41.82B17G001 EMI VIDEO GASKET N 3 41.82G03G001 EMI GASKET USB CONNECT OR EP719 N 4 41.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 27 3 2 6 5 3 4 1 ASSY DC-DC MODULE P3250 ITEM P/N DECRIPTION Supply 70.89Y28GR01 ASSY DC-DC MODULE FOR P3150/P3250 (SERVICE) 1 42.004A1G001 W .A.4P #24/#26 100mm DC.DC/BALLAST 2 42.004B1G001 W .
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 28 ASSY LAMP HOUSING MODULE P3250 4 4 4 4 2 3 6 1 5 ITEM P/N DECRIPTION Supply 1 43.89S01G001 TH-RMAI SWITCH WITH BRACKET (KLIX- ON YSII) 2 49.85M03G001 SYSTEM F AN/55*55*15mm 3 61.89Z06G001 LAMP HOUSING MG ALLOY EX330 N 4 85.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 29 ASSY SPEAKER MODULE P3250 ITEM P/N DECRIPTION Supply 1 49.89Y01G001 SPEAKER MINI IW 4 ohm 140 mm P3150 2 52.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 30 ASSY ENGINE MODULE P3250 4 1 24 1 1 14 15 15 10 13 15 15 3 19 2 7 8 9 16 17 18 12 5 20 6 21 24 24 23 25.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 31 ITEM P/N DECRIPTION Supply 70.89Y22GR01 ASSY ENGINE MODULE FOR P3150/ P3250(SERVICE) 1 70.89Y15G001 ASSY ENGINE BOTT OM COVER P3150 N 2 70.89Y05G001 ASSY ENGINE BASE MODULE P3150 N 3 70.89Y16G001 ASSY ROD MODULE P3150 N 4 70.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 32 1 1 10 6 7 9 8 5 1 4 3 2 AK. P3250 ITEM P/N DECRIPTION Supply 1 36.00006G031 W ARRANTY CARD ,EUROPE FOR ACER N 2 36.00027G001 SER VICE ST A TION CARD N 3 36.89Y01G001 USER’S GUIDE MUL TILINGUAL (C N 4 36.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 33 18 9 12 17 16 15 20 21 19 23 22 10 3 1 5 2 20 DP . P3250.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 34 ITEM P/N DECRIPTION Supply 1 51.00201G001 HANDLE BAR 1.PE HD70 N 2 51.00200G001 HANDLE BAR 2. PE HD70 N 3 55.89Y01G001 CART ON CARRY BOX P3150 N 4 55.89Y02G001 CENTER P APER BOX P3150 N 5 35.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 35 Appendix B 3 I. Serial Number System Denition Serial Number Format for Projector(for non-refresh models,take P3150 for example) EYJ670.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 36 Serial Number Format for Projector(for refresh models,take P3150refresh for example) EYJ8401006 829 00000 59 0 1 1 2 3 4 5 1 : EYJ8401006.
P3150/P3250/P3150 Refresh/P3250 Refresh/P3251 Condential 37 II. PCBA Code Denition PCBA Code for Projector A B XXX XXXXXXXXX CC XXX EEEE 1 : ID 2 : V endor Code 3 : Firmware V ersion 4 : P/N 5 :.
An important point after buying a device Acer P3150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Acer P3150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Acer P3150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Acer P3150 you will learn all the available features of the product, as well as information on its operation. The information that you get Acer P3150 will certainly help you make a decision on the purchase.
If you already are a holder of Acer P3150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Acer P3150.
However, one of the most important roles played by the user manual is to help in solving problems with Acer P3150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Acer P3150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center