Instruction/ maintenance manual of the product EO1-33016 Toshiba
Go to page of 34
TEC Thermal Printer B-670 SERIES Owner ’ s Manual Table of Contents.
Copyright © 2002 by TOSHIBA TEC CORPORATION All Rights Reserved 570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPAN This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
(i) Safety Summary ENGLISH VERSION EO1-33016 Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment.
(ii) Safety Summary ENGLISH VERSION EO1-33016 CAUTION This indicates that there is the risk of personal Injury or damage to objects if the machines are improperly handled contrary to this indication.
T ABLE OF CONTENTS 1. INTRODUCTION .............................................................................................. E1- 1 1.1 APPLICABLE MODEL .............................................................................. E1- 1 1.2 ACCESSORIES .
1.1 APPLICABLE MODEL • B-672-QQ Model name description B - 6 7 2 - Q Q Destination Code QQ : North America bloc Thermal direct/Thermal transfer 1.2 ACCESSORIES Quality control report Power Cord Owner's Manual (EM1-33039) Print Head Cleaner (24089500013) Media Holder Left/Right Side Holder Holder Shaft Holder Base Thumbscrew (M-4x6) 1.
E2-1 2. SPECIFICATIONS ENGLISH VERSION EO1-33016 2. SPECIFICA TIONS 2.1 PRINTER 2.1 PRINTER ∗ Data Matrix TM is a trademark of International Data Matrix, Inc.
E2-2 2. SPECIFICATIONS ENGLISH VERSION EO1-33016 2.2 OPTION 2.2 OPTION Description A stop and cut swing cutter This interface kit allows extremely high speed information transfer between the printer and PC. This module strips the label from the backing paper with the take-up block and strip block.
E2-3 2. SPECIFICATIONS ENGLISH VERSION EO1-33016 NOTES: 1. The media specification other than above are unchanged. 2. When marking black marks on label rolls, the following requirements must be satisfied. When the gap length is less than 4 mm: The black mark length should be longer than the gap length.
E3-1 3. OVERVIEW ENGLISH VERSION EO1-33016 3. OVER VIEW 3.1 FRONT/REAR VIEW 3.1 FRONT/REAR VIEW Front View Rear View 3.2 OPERA TION P ANEL POWER ON LINE ERROR FEED REST ART PAUSE MESSAGE DISPLAY (LCD) Displays messages in the language selected by DIP switch.
E4-1 4. DIP SWITCH FUNCTIONS ENGLISH VERSION EO1-33016 4. DIP SWITCH FUNCTIONS The DIP switches are located to the right of the Guide Wheel. 4. DIP SWITCH FUNCTIONS NOTES: The Shaded settings are the factory default settings. "OFF" means "OPEN".
E5-1 5. SET UP PROCEDURE ENGLISH VERSION EO1-33016 5. SET UP PROCEDURE 5.1 REQUIREMENTS FOR OPERA TION The B-670 has the following requirements: • The host computer must have a serial port or centronics parallel port. • To communicate with host, either an RS-232C cable or Centronics cable is required.
E6-1 6. INSTALLATION PROCEDURE ENGLISH VERSION EO1-33016 6. INST ALLA TION PROCEDURE 6.1 CONNECTING THE POWER CORD AND CABLES 6.1 CONNECTING THE POWER CORD AND CABLES Fig.
E7-1 7. LOADING THE RIBBON ENGLISH VERSION EO1-33016 7. LOADING THE RIBBON 7. LOADING THE RIBBON WARNING! 1. Do not touch moving parts. To reduce the risk that fingers, jewelry, clothing, etc., be drawn into the moving parts, push the switch in the “OFF” position to stop movement.
E7-2 7. LOADING THE RIBBON ENGLISH VERSION EO1-33016 7. LOADING THE RIBBON 5. Push the ribbon core against the spring guide wheel, align the protrusion of the guide wheel with the notch of the ribbon core, then set the ribbon. 6. To remove the slack of the ribbon, turn the ribbon core in the direction indicated by the arrow.
E8-1 ENGLISH VERSION EO1-33016 8. LOADING THE MEDIA 8. LOADING THE MEDIA 8. LOADING THE MEDIA 3. Lock the Media Holder securely with the Lock Lever. 4. Pass the Holder Shaft through the Media, then set one of the Media Holders and lock it securely with the Lock Lever.
E8-2 ENGLISH VERSION EO1-33016 8. LOADING THE MEDIA 8. LOADING THE MEDIA 5. Turn the Lock Levers of the Media Holders to the unlock position and readjust the Media position to the center. Then lock the Media Holders securely with the Lock Levers. Fit the Media Guides to the Media.
E8-3 ENGLISH VERSION EO1-33016 8. LOADING THE MEDIA 8. LOADING THE MEDIA 7. Set the black mark/feed gap sensor to the correct position by turning the adjusting knob. Turning the knob right will move the sensor towards the center of the media while turning left will move it away from the center of the media.
E8-4 ENGLISH VERSION EO1-33016 8. LOADING THE MEDIA 8. LOADING THE MEDIA 8. The media is now loaded and the sensor position is set. Batch type: Media Fig. 8-6 Fig. 8-7 Media Media Outlet Cutter Module Cutter type: Where a cutter is fitted load the media as standard and feed it through the cutter module.
E8-5 ENGLISH VERSION EO1-33016 8. LOADING THE MEDIA 8. LOADING THE MEDIA Strip type: 1 Strip labels from the backing paper for about 200-mm long from the top edge of the label roll. 2 Lower the backing paper release bar. 3 Pass the backing paper between the strip roller and the backing paper holder.
E9-1 ENGLISH VERSION EO1-33016 9. INSERTING THE OPTIONAL FLASH MEMORY CARD 9. INSERTING THE OPTIONAL FLASH MEMORY CARD 9. INSERTING THE OPTIONAL FLASH MEMOR Y CARD Fig. 9-1 1. Turn the power off. 2. Insert the flash memory card into the memory card slot on the rear of the printer.
E10-1 ENGLISH VERSION EO1-33016 10. CARE/HANDLING OF THE MEDIA AND RIBBON 10. CARE/HANDLING OF THE MEDIA AND RIBBON 1 0. CARE/HANDLING OF THE MEDIA AND RIBBON • Do not store the media and ribbon for longer than the manufactures recommended shelf life.
E11-1 ENGLISH VERSION EO1-33016 11. GENERAL MAINTENANCE 11.1 CLEANING 11. GENERAL MAINTENANCE WARNING! 1. Be cafeful when handling the print head as it becomes very hot. 2. Care must be taken not to injure yourself with the printer paper cutter. 3. Do not touch moving parts.
E11-2 ENGLISH VERSION EO1-33016 11. GENERAL MAINTENANCE 11.1 CLEANING 7. Turn the pinch roller lever to the right. 8. Remove the white screw and detach the ribbon end sensor plate. NOTE: When installing the ribbon end sensor plate, be sure to fit both studs in the notches of the ribbon end sensor plate.
E11-3 ENGLISH VERSION EO1-33016 11. GENERAL MAINTENANCE 11.2 UNDER THE MEDIA GUIDES 11.2 UNDER THE MEDIA GUIDES 1. Remove the Media Guides. 2. Remove the jammed Media. 3. Clean “dust and glue” on the Media Guides with a soft cloth moistened with alcohol.
E11-4 ENGLISH VERSION EO1-33016 11. GENERAL MAINTENANCE 11.4 REMOVING JAMMED MEDIA 11.4 REMOVING JAMMED MEDIA 1. Turn the power off. 2. Open the top cover, and right side cover. 3. Turn the head lever to position “OPEN, “ then release the head lock plate.
E11-5 ENGLISH VERSION EO1-33016 11. GENERAL MAINTENANCE ■ Cleaning the Cutter Unit 1. Loosen two screws and remove the cutter cover. 2. Remove the white screw and media guide. 3. Remove the jammed paper and trash. 4. Clean the cutter with dry cloth.
E11-6 ENGLISH VERSION EO1-33016 11. GENERAL MAINTENANCE 11.5 THRESHOLD SETTING 11.5 THRESHOLD SETTING For the printer to maintain a constant print position it uses the transmissive sensor to detect the gap between labels by measuring the amount of light passing through the media.
E12-1 ENGLISH VERSION EO1-33016 12. TROUBLESHOOTING 12. TROUBLESHOOTING 12. TROUBLESHOOTING Solution 1. Re-fit the media correctly. → Press the RESTART key. 2. Remove the cause of the jam and replace the media correctly. → Press the RESTART key. 3.
E12-2 ENGLISH VERSION EO1-33016 12. TROUBLESHOOTING 12. TROUBLESHOOTING Solution Turn the power off and decrease the print head temperature. 1. Restart the printing by pressing the RESTART key. 2. Replace the print head. Turn the power off. Contact your Authorized Service representative.
E12-3 ENGLISH VERSION EO1-33016 12. TROUBLESHOOTING 12. TROUBLESHOOTING Solution 1. Check that the media and the ribbon is loaded correctly. 2. Check whether the print head is set correctly or not. 3. Check the cabling between the printer and the host.
.
.
PRINTED IN JAPAN EO1-33016 E.
An important point after buying a device Toshiba EO1-33016 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba EO1-33016 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba EO1-33016 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba EO1-33016 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba EO1-33016 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba EO1-33016, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba EO1-33016.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba EO1-33016. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba EO1-33016 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
