Instruction/ maintenance manual of the product E-STUDIO AS/400 Toshiba
Go to page of 52
Guidance for AS/400 Print Solution.
2 AS/400 Print Solution —.
AS/400 Print Solution — Software License Agreement 3 Sof tware License Agreement INST A LLING OR OT HERWISE USING THIS SOFTW ARE PRODUCT CONSTITUTES YOUR ACCEPT ANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEP ARA TE LICENSE IS PROVIDED BY THE SUPPLIER OF APPLICABLE SOFTW ARE IN WHICH CASE SUCH SEP ARA TE LICENSE SHALL APPL Y).
4 AS/400 Print Solution — Software License Agre ement Limit ation of Li ability IN NO EVENT WILL TTEC OR ITS SUPPLIERS BE LIABLE TO YOU FOR ANY DAMAGES, WHETHER IN CONTRACT , TORT , OR OTHERWISE (EX.
AS/400 Print Soluti on — Trademarks and Copyright 5 T rademarks and Copyright T rademarks • Copyright permissions rega rding screenshots, pictures and descriptions, included in this document, can be obtained from AXIS Communications AB.
6 AS/400 Print Solution — Disclaimer Notice Disclaimer Notice The following notice sets out the exclusions and limitations of liabili ty of TOSHIBA TEC CORPORA TION (includ ing its employees, agents.
AS/400 Print Solution — Preface 7 Preface The e-STUDIO520/600/720/85 0, e-STUDI O281C/351C/451C, e-STUDIO35 2/452, e-STUDIO202L/232/282, e - STUDIO2500 C/3500C/3510C , e-STUDIO165/205, e-STUDIO167/2.
8 AS/400 Print Solution — Preface.
AS/400 Print Solution — T able of Contents 9 T able of Content s Software License Agreement .................... ......... ................. ............ ............. .. 3 Trademarks and Copyright .............. ............. ................ .....
10 AS/400 Print Solution — T able of Contents.
AS/400 Print Soluti on — 1. AXIS Network Print Server 1 1 1. AXIS Network Print Server.
12 AS/400 Print Solution — Overview Overview Component s The components of the AS/400 ® Printing Solution are: • AS/400 server • Y our eq uipment • USB cable to connect the AXIS 5570e Print S.
AS/400 Print Solution — Overview 13 Finishing options and logical printers TOSHIBA of fers several fin ishing options in addition to standard pr int commands com- ing from the AS/400.
14 AS/400 Print Soluti on — Inst allation Inst allation Inst allation procedure Install the AS/400 printing solution in two steps: 1. Set up the hardware 2. Set up the AS/400 printer Step 1: Set up the hardware NOTE: • The controller can be directly connected to the AS/400 network at th e same time.
AS/400 Print Solution — Installation 15 Step 2: Set up the AS/400 printer On the AS/400, use the CRTDEVPR T command to configure the print settings accord- ing to the following table: All other settings can be left unchanged. NOTE: • If you experience any problems, press F1 for help.
16 AS/400 Print Soluti on — Inst allation NOTE: • T o protect the admin pages and the Config uration Wizard from un authorized use, enter a password (by default set to pass) in the Root Password fi eld under Admin General Settings. • Use the same port number when creating the print devi ce (page 15).
AS/400 Print Solution — Configurati on 17 Configuration A vailable AXIS firmware version Use the production releas e version or serv ice release version gi ven in the following table when using TOSHIBA MFP . All official firmware releases for the AXIS 5570e are available on AXIS website.
18 AS/400 Print Solution — Configuration 8. The print server will rest art in five seconds running the n ew sof tware. Update procedure o f the config file: 1. Get the config file by FTP . Open a Windows command prompt and enter the following: ftp <ip address> default user name root default password pass get config bye 2.
AS/400 Print Solution — Configurati on 19 Copier model When printing portrait data, select an a ppropriate copier model, e.g. T oshiba eSTUDIO520/600/720/850 or T osh iba eSTUDIO281C/351C/4 51C. When printing lan dscape data, select Cust om copier driver for Copier model.
20 AS/400 Print Solution — Configuration Only PCL available In the Configurati on Wizard for IBM sessions, select PCL for Printer Driver . PostScript is not available. Edit Session: Only PCL is available for IPDS Printer Driver under Edit Session. PostScript is not available.
AS/400 Print Solution — Configurati on 21 A vailable finisher options The following options are avail able for the se ttings of Logical Printe rs or Edit Session. Duplex: Edit Session: Long Edge Binding and Short Edge Binding are ava ilable for Duplex under Edit Ses- sion.
22 AS/400 Print Solution — Configuration Logical Printers: LONG_EDGE_BINDING and SHORT_EDGE_B INDING a re available for Copi er Duplex under Logical Printe rs. Stapl e : Edit Session: T op Left Slant, T op Double, Left Double and T op Right are avail able for S taple under Edit Session.
AS/400 Print Solution — Configurati on 23 Logical Printers: TOP_LEFT_SLANT , TOP_RIGHT , TOP_DOUBLE and LEFT _DOUBLE are available for Copier S taple under Logical Printers. TOP_LEFT_HORIZONT AL, TOP_LE FT_VER TICAL, BOTTOM _LEFT , BOTTOM_RIGHT and CENTER are not available.
24 AS/400 Print Solution — Configuration Hole Punch: Edit Session: Long Edge and Short Edge are availabl e for Hole Punch under Edit Session. Logical Printers: LONG_EDGE and SHORT_EDGE are available for Copier Hole Punch under Lo gical Printers. NOTE: • e-STUDIO165/205 and e-STUD IO167/207/237 are not supporting the Hole Punch Option.
AS/400 Print Solution — Configurati on 25 Fold: Fold option is not available. Edit Session: Logical Printers: HALF_FOLD and Z_FOLD are not avail able for Copier Fold under Logical Printe rs.
26 AS/400 Print Solution — Configuration Paper Source: Default and 1-4 are availabl e for Paper Source. Default: Auto select 1: Upper Cassette 2: Lower Cassette 3: 1st Pedestal or Large Capacity Fee.
AS/400 Print Solution — Configurati on 27 Logical Printers: 5 is not available for Copier Paper Sources under Logica l Printers. Copies: The Copies option is for selecting the number of copies.
28 AS/400 Print Solution — Configuration General settings Select DISABLE for Pr inter Info rmation and Bidire ctional control i f extra data, which is specified as "P AGEC OUNT", is printed.
AS/400 Print Solution — Configurati on 29 IPDS emulator IPDS bin under the IPDS Configuration tab is used for setting the paper size. S tatement, Ledger , Fo lio, Hagaki, Letter , Legal, A4 and A3 are available. Executive and Custom are not available.
30 AS/400 Print Solution — Configuration For PCL Bin number , the availab le value for TOSHIBA MFP is as follows: 1: Upper 2: Bypass 4: Lower 5: Pedestal Upper or Large Capacity Feeder 7: Auto 21: P.
AS/400 Print Solution — Configurati on 31 Custom copier driver When you print landscape data with some finisher options e nabled, you may ne ed to use the Custom Copier Driver for correct output. Obtain the information about the Cus- tom copier driver functionality from AXI S COMMUNICA TIONS web site.
32 AS/400 Print Soluti on — Problem Solving Problem Solving Problems and recommended solutions The following table provides suggestions for reso lving printing problems. Customer service For help with AXIS 5570e Print Server q uestions, go to the AXIS COMMUNICA TION S section of www .
AS/400 Print Solution — 2. WorkS tation Cust o mization Object for TOSHIBA e-STUDIO 33 2. W orkS t ation Customization Object for T OSHIBA e-STUDIO.
34 AS/400 Print Solution — Overview Overview Component s The components of the AS/400® Printing Solution are: • AS/400 Server OS version 5.2 or later (The latest PTF is recommended) • Y our eq uipment ( See NOTE below .
AS/400 Print Solution — Installation 35 Inst allation Inst allation procedure Before installing the WorkS tation Customization Object for TOSHIBA e-STUDIO, con- figure the system environments as follows: • Set up AS/400 Server under the environment that allow s you to use prin ting func- tions.
36 AS/400 Print Soluti on — Inst allation 4. The setting screen for OUT Q appears as the inst allation is executed. S pecify the name of OUTQ (maximum 7 bytes) to be used, it s library , the IP addre ss of the printer and default tray type*. Then press the execution key .
AS/400 Print Solution — Installation 37 Step 2: Setting up W orkSt ation Customizatio n Object for TOSHIBA e-STUDIO This section describe s how to set up the W orkS tation Customization Object for TOSHIBA e-S TUDIO. 1. Login as a user with QSECOFR authority .
38 AS/400 Print Soluti on — Inst allation Step 3: St arting up auto assign (resi dent) program This section describes how to start up auto assign (resid ent) program. NOTE: • It is recommended to load the auto assign (re sident) program into IPL. 1.
AS/400 Print Solution — Installation 39 4. The program is st arted up. • Execute a command [WRKACTJOB] to display the list. If the status of this pro- gram is displayed as "DEQA" in the list, the program is properly started up.
40 AS/400 Print Solution — Uninstallation Uninst allation Uninst allation procedure Step 1: Uninsta lling Work St ation Customization Object for T OSHIBA e-STUDIO 1. Execute a command [WRKACTJOB] and then select a resi- dent OUTQ monitoring progra m.
AS/400 Print Solution — Uninstallation 41 2. Execute a command [DL TOUTQ OUTQ(library name / OUTQ name *1 )] to delete the OUTQ specified at the inst allation. *1: It shall be the OUTQ name specified at the installati on or the setup. 3. Execute a command [ENDWTR OUTQ name *1 01*IMMED] to disconnect the printer .
42 AS/400 Print Solution — Uninstallation NOTE: • The part "01" after the OUTQ name shall be changed from "01 " through "07" as you repeat this command se ven times. 4. Execute a command [WRKOUTQ OUTQ na me *1 *] to confirm that no spool remains.
AS/400 Print Solution — Uninstallation 43 If "Files" is a value other than "0 " and also there are remaining spools, select optio n "5" to delete the remaining spools. 5. Execute a command [DL TLIB WTEC02] to delete the product library .
44 AS/400 Print Solution — Operation Operation Operational procedure Follow the procedure below to operate the WorkS tation Customization Object for TOSHIBA e-S TUDIO. 1. Speci fy print file script (ORIENT A TION, ST APLE, DUPLEX and DRA WER) for a document to be printed with the MFP .
AS/400 Print Solution — Operation 45 Print file script S pecify print file script below according to the printin g style of a document to be printed with an MFP .
46 AS/400 Print Solution — Operation LONG_EDGE: DUPLEX(*YES) SHORT_EDGE: DUPLEX(*TUMBLE) ABCD EFG Portrait ABCD EFG Landscape ABCD E... ABCD EFG ABCD EFG ABCD EFG ABCD E.
AS/400 Print Solution — Appendix 47 Appendix St apling specifications *1: OUTQ numbers assigned b y resident programs. OUTQ*1 Printing Specifications A vailable Sizes Remarks Por- trait/ Land- scape.
48 AS/400 Print Solution — Appendix Printing character size - Reference values * All paper sizes noted “-R” are rotated in “P AGR TT (90)”. Paper Size CPI Line Char .
AS/400 Print Solu tion — Glossary 49 Glossary Definitions of T erms T erm Definition DLC D ata L ink C ontrol, the data link layer protocol. Duplex The process of pr inting on both si des of a sheet of paper . Finishing opti on A feature provided by TOSHIBA printers and copie rs for doing such things as stapling and hole punching documents.
50 AS/400 Print Solution — Definitions of T erms.
DP-2090/2520/3000/3570/4570 DP-5550/6550/7550/8550 FC-2020C/2330C/2820C/2830C/3520C/3530C/4 520C FC-5520C/6520C/6530C DP-1670/2070/2370 FC-2500C/3500C/3510C DP-1650/2040 FC-281C/351C/451C DP-5200/6000.
2006 - 2010 T OSHIBA TEC CORPORA TION All rights reserved 2-17-2, HIGASHIGOT ANDA, SHINAGA W A-KU, T OKYO, 141-8664, JAP AN Guidance for AS/400 Print Solution R060120B3909-TTEC V er09 2010-07.
An important point after buying a device Toshiba E-STUDIO AS/400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba E-STUDIO AS/400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba E-STUDIO AS/400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba E-STUDIO AS/400 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba E-STUDIO AS/400 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba E-STUDIO AS/400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba E-STUDIO AS/400.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba E-STUDIO AS/400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba E-STUDIO AS/400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
