Instruction/ maintenance manual of the product Density (Consistency) Meter LQ500 Toshiba
Go to page of 9
No. EJL- 106A Density (Consistency) Meter LQ500 Introduction The LQ500 density (consistency) meter uses microwave phase shift technology to determine concentrations of solids in the material to be measured flowing through pipes.
LQ500 2 range, which is the upper limit setting range. Resolution: Meter size 50 mm (2”) 80 mm (3”)to 300 mm (12”) Resolution 0.002%TS 0.001%TS Note 1: Above values are the results of comm uting ability in the phase measurements of the converter.
LQ500 3 200 mm (8”) 8 mS/cm maximum 250 mm (10”) 8 mS/cm maximum 300 mm (12”) 6 mS/cm maximum Note 1: The LQ500 can not have an accurate density (consistency) me asurement when it is over the specification according to reduce the microwave s ignal.
LQ500 4 hours when programming every 5 minutes. • Moving average function: In order to keep the average density (consistency) output, or in order to suppress the deflection width of the output. It helps for densit y (consistency) control. <Specification> Enable to determine a number from 1 to 99.
LQ500 5 11 0 (4.3”) (1 19) (4.7”) Converter commu nicatio n port Steel pipe (50A) (2”) 360 (14.2”) 390 (15.4”) 234 (9.2”) Contact sign al I/O port (1) Contact sign al I/O port (2) Densi ty.
LQ500 6 (7) Install an adjustable piping mechanism if there is a possibility that the detector pipe m ay not fit between mating flanges. (8) Install the LQ500 in a place where enough water pressure is applied. Therefore, it is recommended that the LQ500 be installed as far away as possible from the pipe outlet opened to atmosphere.
LQ500 7 L1 L2 Tx+ TX- Rx+ Rx- SG FG +24V 0V FG Ec+ Ec- FG Tx+ Tx- Rx+ Rx- SG FG +24V 0V FG Communication cable Power su pply cable Converter Power su pp l y 100 to 240 V ac , 50/60Hz Ground terminal (PE) (Ground re sistan ce 100 ohm or less ) Densi ty ( cons ist en cy) mea surem ent outp ut (4-20mAdc, 750 ohm max .
LQ500 No. EJL-106A Ordering Information When ordering the LQ500, refer to Table 4. Type Specification Code. An entry must be made for each of the columns. The following items must also be specified: 1. Fluid characteristics: • Type of material to be measured • Density (consistency) (max.
LQ500 9 Table 4. Type Specification Code (LQ500 Density (consistency) Meter) TYPE CAT Code SPECIF ICATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L Q 5 0 0 Microwave Density (Consistency) Meter A S t a n d a.
An important point after buying a device Toshiba Density (Consistency) Meter LQ500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba Density (Consistency) Meter LQ500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba Density (Consistency) Meter LQ500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba Density (Consistency) Meter LQ500 you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba Density (Consistency) Meter LQ500 will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba Density (Consistency) Meter LQ500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba Density (Consistency) Meter LQ500.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba Density (Consistency) Meter LQ500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba Density (Consistency) Meter LQ500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
