Instruction/ maintenance manual of the product A10 Series Toshiba
Go to page of 259
T OSHIBA Satellite A10 Series Port able Personal Computer User ’ s Manual.
Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the informa- tion contained herein.
FCC information Product Name : Satellite A10 Model number : PSA10 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 . This device may not cause harmful interference. 2 . This device must accept any interference received, including interference that may cause undesired operation.
Modem warning notice Conformity St atement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN).
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures.
Jap an regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection.
Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, opera- tional and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s).
3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Canada: 1353A-L4AINT Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit.
Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions.
ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) ❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a ) a person calling your modem will hear a short burst of ringing before the modem answers.
General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork.
TEAC CD-ROM drive CD-224E, CD- RW/DVD-ROM drive DW-224E safety instruction CAUTIONS: 1. The CD/DVD drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PROD- UCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
3. To prevent direct exposure to the laser beam, do not try to open the enclosure. CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
vermeiden darf das Gerät nicht geöffnet werden. ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
HIT ACHI DVD-ROM drive GDR-8082 safety instruction CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an autho- rized service location.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUST- MENTS OR PERFORMANCE OF PROCE- DURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.
ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
xxiii T able of Content s Preface Manual contents ............................................................................. xxxi Conventions ................................................................................... xxxii Abbreviations ..
xxiv Communications ................................................................................. 1 - 7 Security .............................................................................................. 1 - 7 S o f t w a r e .................
xxv Restoring the preinstalled software from the Product Recovery CD-ROM ....................................................... 3-12 Chapter 4 Operating Basics Pointing devices .........................................................................
xxvi Chapter 5 The Keyboard Typewriter keys ................................................................................. 5 - 1 F1 … F12 function keys ..................................................................... 5 - 2 Soft keys: Fn key combinati ons .
xxvii Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7 - 1 Accessing HW Setup ......................................................................... 7 - 1 HW Setup window .
xxviii CD-RW/DVD-ROM drive ................................................................... 9-14 DVD-R/-RW drive .............................................................................. 9-16 Diskette drive ....................................
xxix Appendix I Parts Numbers .................................................................................... I-1 Glossary Index.
xxx.
xxxi Preface Congratulations on your purchase of the Satellite A10 series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing.
xxxii Chapter 4, Operating Basics , includes instructions on using the following devices: Touch Pad, USB diskette drive, optical media drives, modem, wireless communica- tion features, LAN. It also provides tips on care of the computer, diskettes and CD/ DVDs.
xxxiii Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys.
xxxiv.
xxxv General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
xxxvi Central Processing Unit ("CPU") Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions: 1. use of certain external peripheral products 2. use of battery power instead of AC power 3.
I NTRODUCTION Chapter 1 Introduction Equipment checklist .......................................................................... 1 - 1 Hardware ............................................................................................ 1 - 1 S o f t w a r e .
I NTRODUCTION.
1-1 I NTRODUCTION Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not prein- stalled by TOSHIBA.
1-2 User's Manual I NTRODUCTION • Online manual ❑ Product Recovery CD-ROM Document ation • Satellite A10 Series Portable Personal Computer User's Manual • Microsoft Windows XP manual.
1-3 I NTRODUCTION Memory Slots 128, 256 or 512 MB memory modules can be installed in the two memory slots for a maximum of 1 GB system memory. Video RAM Allocated a part of System Memory dynamically.
1-4 User's Manual I NTRODUCTION • CD-ROM Mode 1, Mode 2 • CD-ROM XA Mode 2 (Form1, Form2) • Enhanced CD (CD-EXTRA) • CD-G (Audio CD only) • Addressing Method 2 DVD-ROM drive Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.
1-5 I NTRODUCTION DVD-R/-RW drive Some models are equipped with a full- size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run either 12cm (4.72") or 8cm (3.15") CDs/12cm(4.72") DVDs without using an adaptor.
1-6 User's Manual I NTRODUCTION Pointing device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer. Ports Parallel Some models are equipped with a parallel port for parallel printer or other parallel device (ECP compatible).
1-7 I NTRODUCTION Special features Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions.
1-8 User's Manual I NTRODUCTION Hot keys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
1-9 I NTRODUCTION Battery save mode This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in TOSHIBA Power Saver. Panel power off/on This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened.
1-10 User's Manual I NTRODUCTION HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To start the utility, click the Windows Start button and click Control Panel.
1-11 I NTRODUCTION Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory expansion A 128, 256 or 512 MB memory module (PC2100, DDR) can easily be installed in the computer.
1-12 User's Manual I NTRODUCTION.
T HE G RAND T OUR Chapter 2 The Grand T our Front with the display closed ........................................................... 2 - 1 Left side .............................................................................................. 2 - 2 Right side .
T HE G RAND T OUR.
T HE G RAND T OUR 2-1 Chapter 2 The Grand T our This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position.
User's Manual T HE G RAND T OUR 2-2 Wireless Slide this switch toward the left of the computer to turn communication off Wireless LAN function. Slide it toward the right of switch the computer to turn on the functions (Wireless LAN model or Wireless LAN ready model only).
T HE G RAND T OUR 2-3 Right side Headphone jack This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automati- cally disabled. PC card slot A PC card slot can accommodate one 5 mm Type II card.
User's Manual T HE G RAND T OUR 2-4 DVD-R/-RW drive Some models are equipped with a full-size DVD-R/-RW drive module that lets you record data to rewritable CD/ DVDs as well as run CD/DVDs without using an adaptor.
T HE G RAND T OUR 2-5 Link indicator This indicator glows green when the computer is connect- (green) ed to a LAN and the LAN is functioning properly. Parallel port Some models are equipped with a Centronics-compatible, 25-pin parallel port that is used to connect a parallel printer or other parallel device.
User's Manual T HE G RAND T OUR 2-6 Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. Figure 2-5 The underside of the computer Battery release Slide this latch to release the battery pack for removal.
T HE G RAND T OUR 2-7 Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display to the right of the computer and lift up. Position the display at a comfortable viewing angle.
User's Manual T HE G RAND T OUR 2-8 Stereo speakers The speakers emit sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Power button Press the power button to turn the computer’s power on and off.
T HE G RAND T OUR 2-9 keyboard indicators CD-ROM This indicator glows green when the computer is drive accessing a diskette in the diskette drive or a disk in the CD-ROM,DVD-ROM, DVD-R/-RW or CD-RW/DVD-ROM drive. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator.
User's Manual T HE G RAND T OUR 2-10 Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys.
T HE G RAND T OUR 2-11 NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20 o while it is operating. 2. Do not set anything on top of the diskette drive. Fixed optical media drive CD-ROM drive Some models are equipped with a full-size,CD-ROM drive.
User's Manual T HE G RAND T OUR 2-12 DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly. Code Region 1.
T HE G RAND T OUR 2-13 Code Region 1. Canada, United States 2. Japan, Europe, South Africa, Middle East 3. Southeast Asia, East Asia 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6.
User's Manual T HE G RAND T OUR 2-14 4. Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean 5. Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6. China Universal AC adaptor The universal AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer.
G ETTING S TARTED Chapter 3 Getting S t arted Setting up your work space .............................................................. 3 - 1 General conditions .............................................................................. 3 - 2 Placement of the computer .
G ETTING S TARTED.
3-1 G ETTING S TARTED Chapter 3 Getting S t arted This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort .
User's Manual G ETTING S TARTED 3-2 General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation.
3-3 G ETTING S TARTED Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain.
User's Manual G ETTING S TARTED 3-4 Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare.
3-5 G ETTING S TARTED Connecting the universal AC adaptor Attach the universal AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power.
User's Manual G ETTING S TARTED 3-6 Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1 . Slide the display latch on the front of the computer to the right. 2 . Lift the panel up and adjust it to the best viewing angle for you.
3-7 G ETTING S TARTED 2 . Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power S t arting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo.
User's Manual G ETTING S TARTED 3-8 3 . Click start then click Turn Off Computer . From the Turn Off Computer menu select Turn Off . 4 . Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately.
3-9 G ETTING S TARTED Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4 . See Chapter 5, Keyboard , for details. To enter Hibernation mode, follow the steps below. 1 . Click start . 2 . Select Turn Off Computer . 3 . Open the Turn Off Computer dialog box.
User's Manual G ETTING S TARTED 3-10 CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. St andby mode If you have to interrupt your work, you can turn off the power without exiting from your software.
3-11 G ETTING S TARTED ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature. ❑ You can use the panel power off feature. Executing standby NOTE: You can also enable Standby by pressing Fn + F3 .
User's Manual G ETTING S TARTED 3-12 Rest arting the computer Certain conditions require that you reset the system. For example, if: ❑ You change certain computer settings. ❑ An error occurs and the computer does not respond to your keyboard commands.
O PERATING B ASICS Chapter 4 Operating Basics Pointing devices ................................................................................ 4 - 1 Using the Touch Pad .......................................................................... 4 - 1 Using the USB diskette drive .
O PERATING B ASICS Moving the computer ...................................................................... 4-23 Heat dispersal .....................
O PERATING B ASICS 4-1 Chapter 4 Operating Basics This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication, and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs.
User's Manual O PERATING B ASICS 4-2 Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port.
O PERATING B ASICS 4-3 Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1 .
User's Manual O PERATING B ASICS 4-4 Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1 . a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. Figure 4-3 Pressing the DVD-ROM eject button b.
O PERATING B ASICS 4-5 2 . Pinch the drawer gently and pull until it is fully opened. Figure 4-5 Pulling the drawer open 3 . Lay the CD/DVD, label side up, in the drawer. Figure 4-6 Inserting a CD/DVD NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.
User's Manual O PERATING B ASICS 4-6 CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Be careful to keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive.
O PERATING B ASICS 4-7 Writing CDs on CD-RW/DVD-ROM drive CAUTIONS: 1. When the drawer pops open slightly, wait a moment to make sure the CD/DVD has stopped spinning before pulling the drawer fully open. 2. Turn off the power before you use the eject hole.
User's Manual O PERATING B ASICS 4-8 Before writing or rewriting Please observe the following points when you write or rewrite the data. ❑ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates.
O PERATING B ASICS 4-9 ❑ Do not perform any of the following actions: • Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. • Start a communication application such as a modem. • Apply impact or vibration to the PC.
User's Manual O PERATING B ASICS 4-10 ❑ Any change or loss of the recorded contents of CD-R/RW or DVD-R/-RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.
Read/write function chart Disc type C D - R CD -R W DVD-R DVD-RW DVD-RAM DVD+R DVD+RW Read Write Drag’n Drop CD*1 No No No No No No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No *1 Software supplied with the product can be used for writing to a disc.
User's Manual O PERATING B ASICS 4-12 ❑ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-RW disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc.
O PERATING B ASICS 4-13 Writing CD/DVDs on DVD-R/-RW drive ❑ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data.
User's Manual O PERATING B ASICS 4-14 ❑ Make sure writing or rewriting is completed before going into standby/ hibernation. ❑ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains, or cars. Do not use an unstable surface such as a stand.
O PERATING B ASICS 4-15 Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1 .
User's Manual O PERATING B ASICS 4-16 6 . Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields. Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack.
O PERATING B ASICS 4-17 3 . Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location.
User's Manual O PERATING B ASICS 4-18 Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region.
O PERATING B ASICS 4-19 Figure 4-11 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1.
User's Manual O PERATING B ASICS 4-20 ❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s. (Revision A, Revision A/B combo type) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.
O PERATING B ASICS 4-21 Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communi- cation functions. Indicator status Indication Ind ica to r off Wireless communication switch is set to off. Indicator glows Wireless communication switch is on.
User's Manual O PERATING B ASICS 4-22 Connecting LAN cable CAUTION: The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.
O PERATING B ASICS 4-23 CAUTION: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1 . Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2 . Disconnect the cable from the LAN hub in the same manner.
User's Manual O PERATING B ASICS 4-24 ❑ Close all port covers. ❑ Use the carrying case when transporting the computer. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered.
T HE K EYBOARD Chapter 5 The Keyboard Typewriter keys ................................................................................. 5 - 1 F1 … F12 function keys ..................................................................... 5 - 2 Soft keys: Fn key combinati ons .
T HE K EYBOARD.
5-1 T HE K EYBOARD Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer.
User's Manual 5-2 T HE K EYBOARD F1 … F12 function keys The function keys, not to be confused with Fn , are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed.
5-3 T HE K EYBOARD Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard.
User's Manual 5-4 T HE K EYBOARD Hot keys Hot keys ( Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon.
5-5 T HE K EYBOARD Standby: When you press Fn + F3 , the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4 , the computer enters Hibernation.
User's Manual 5-6 T HE K EYBOARD LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver.
5-7 T HE K EYBOARD Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “ F number ” key. To start the TOSHIBA Accessibility Utility, click start , point to All Programs , point to TOSHIBA Utilities and click Accessibility .
User's Manual 5-8 T HE K EYBOARD Numeric mode To turn on the Numeric mode, press Fn + F11 . The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2.
5-9 T HE K EYBOARD T emporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn . 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay.
User's Manual 5-10 T HE K EYBOARD.
P OWER AND P OWER -U P M ODES Chapter 6 Power and Power-Up Modes Power conditions ............................................................................... 6 - 1 Power indicators ..................................................................
P OWER AND P OWER -U P M ODES.
P OWER AND P OWER -U P M ODES 6-1 Chapter 6 Power and Power-Up Modes The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
6-2 User's Manual P OWER AND P OWER -U P M ODES Table 6-1 Power conditions continued Power on Power off (no operation) A C Battery • Operates adaptor charge is • LED: Battery off no t above l.
P OWER AND P OWER -U P M ODES 6-3 No light Under any other conditions, the indicator does not light. NOTE: If the battery becomes too hot while it is being charged, the charge will stop and the battery indicator will go out. When the battery’s temperature falls to a normal range, charge will resume.
6-4 User's Manual P OWER AND P OWER -U P M ODES Battery p ack When the universal AC adaptor is not connected, the computer’s main power source is a removable lithium-ion battery, also referred to in this manual as the battery pack. You can purchase additional battery packs for extended use of the computer away from an AC power source.
P OWER AND P OWER -U P M ODES 6-5 **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key to set Date/Time. CAUTION: The computer’s RTC battery is a nickel metal hydride battery and should be replaced only by your dealer or by a TOSHIBA service representative.
6-6 User's Manual P OWER AND P OWER -U P M ODES 3 . Never short-circuit the battery pack by contacting the terminals with a metal object. A short-circuit can cause fire or otherwise damage the battery pack and possibly cause injury.
P OWER AND P OWER -U P M ODES 6-7 Care and use of the battery pack 3 . Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture.
6-8 User's Manual P OWER AND P OWER -U P M ODES 2 . To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures.
P OWER AND P OWER -U P M ODES 6-9 Charging time (hours) Battery type Power on Power off Battery pack 3600mAh 3 . 5 t o 9 o r l onger about 2.6 4400mAh 4 t o 1 1 o r longer about 2.
6-10 User's Manual P OWER AND P OWER -U P M ODES Monitoring battery cap acity Remaining battery power can be monitored in the Power Save Modes window in Power Saver. NOTES: 1. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
P OWER AND P OWER -U P M ODES 6-11 Care and use of the battery pack ❑ How much charge the battery contained to begin with. ❑ How you use optional devices, such as a PC card, to which the battery supplies power. ❑ Enabling Standby mode conserves battery power if you are frequently turning the computer off and on.
6-12 User's Manual P OWER AND P OWER -U P M ODES 4 . Connect the universal AC adaptor to the computer and the power cord to a power outlet. The DC IN indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged.
P OWER AND P OWER -U P M ODES 6-13 3. In Hibernation mode, data will be lost if you remove the battery and disconnect the universal AC adaptor before the save is completed. Wait for the Built-in HDD indicator to go out. 4. Do not touch the latch while holding the computer.
6-14 User's Manual P OWER AND P OWER -U P M ODES CAUTIONS: 1. The battery pack is a lithium-ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
P OWER AND P OWER -U P M ODES 6-15 S t arting the computer by p assword To start up the computer with the user password, follow these steps: 1 . Turn on the power as described in Chapter 3, Getting Started . The following message appears: Password = NOTE: At this point, the hotkeys Fn + F1 to F5 do not work.
6-16 User's Manual P OWER AND P OWER -U P M ODES Panel power off You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode.
HW S ETUP Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7 - 1 Accessing HW Setup ......................................................................... 7 - 1 HW Setup window .
HW S ETUP.
7-1 HW S ETUP AND P ASSWORDS Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for Display, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.
User's Manual 7-2 HW S ETUP AND P ASSWORDS General This window displays the BIOS version and contains two buttons: Default and About . Setup This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings.
7-3 HW S ETUP AND P ASSWORDS 4 . If character strings match, the password is registered and the display changes to: The password was registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! To delete a user password: 1 .
User's Manual 7-4 HW S ETUP AND P ASSWORDS Key FD After you set a password, you can create a Key FD (diskette). If you forget the user password, the Key FD lets you bypass the password function. NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost.
7-5 HW S ETUP AND P ASSWORDS Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional .
User's Manual 7-6 HW S ETUP AND P ASSWORDS Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically CPU power consumption and clock speed Switchable automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary.
7-7 HW S ETUP AND P ASSWORDS To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2 . The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD, Network (LAN), PC (ATA) card boot. NOTE: A bar will appear only under the selected device.
User's Manual 7-8 HW S ETUP AND P ASSWORDS HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD.
7-9 HW S ETUP AND P ASSWORDS USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled .
User's Manual 7-10 HW S ETUP AND P ASSWORDS Supervisor p assword Refer to the readme file of the Supervisor Password Utility for instructions on setting the Supervisor Password. The path to the readme file is C:Program FilesTOSHIBAWindows UtilitiesSVPWTool .
O PTIONAL D EVICES Chapter 8 Optional Devices PC cards ............................................................................................. 8 - 2 Inserting a PC card ............................................................................
O PTIONAL D EVICES.
8-1 O PTIONAL D EVICES Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devi.
User's Manual 8-2 O PTIONAL D EVICES PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed.
8-3 O PTIONAL D EVICES Removing a PC card To remove the PC card, follow the steps below. 1 . Click the Safety Remove Hardware icon on the Task Bar. 2 . Click PC card . 3 . Press the PC card eject button to extend it. 4 . Press the extended eject button to pop the card out slightly.
User's Manual 8-4 O PTIONAL D EVICES Memory exp ansion You can install additional memory in the computer’s memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. CAUTION: 1. Use only memory modules approved by TOSHIBA.
8-5 O PTIONAL D EVICES Memory expansion Figure 8-3 Removing the memory module cover 6. Lift one side of the insulator sheet and fit the module’s connectors into the computer’s connectors at about a 45 degree angle. Press the module carefully to ensure a firm connection.
User's Manual 8-6 O PTIONAL D EVICES Figure 8-4 Installing the memory module 8. Seat the cover and secure it with a screw. 9. Replace the battery pack as described in Chapter 6, Power and Power-Up Modes . 10. Turn the power on and make sure the added memory is recognized.
8-7 O PTIONAL D EVICES Figure 8-5 Removing the memory module 6 . Seat the cover and secure it with a screw and replace the battery pack. Battery p ack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery.
User's Manual 8-8 O PTIONAL D EVICES External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1 .
8-9 O PTIONAL D EVICES TV e. Select Television icon. f . Select the Video Standard list box and select the format that your TV supports. *Please select one of them, NTSC-M, NTSC-J or PAL-B from the Video Standard list box though there are lots of selections.
User's Manual 8-10 O PTIONAL D EVICES Figure 8-7 The Adapter window (4 ) Select a resolution from the menu. Figure 8-8 Resolution menu.
8-11 O PTIONAL D EVICES Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the back side of the computer.
User's Manual 8-12 O PTIONAL D EVICES.
T ROUBLESHOOTING Chapter 9 T roubleshooting Problem solving process ................................................................... 9 - 1 Preliminary checklist .......................................................................... 9 - 1 Analyzing the problem .
T ROUBLESHOOTING.
9-1 T ROUBLESHOOTING Chapter 9 T roubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter.
User's Manual T ROUBLESHOOTING 9-2 ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer.
9-3 T ROUBLESHOOTING Hardware If you cannot find a software problem, check your hard- ware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals.
User's Manual T ROUBLESHOOTING 9-4 Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds.
9-5 T ROUBLESHOOTING Overheating power down If the computer’s internal temperature becomes too high, the computer will automati- cally shut down. Problem P rocedure Computer shuts down Leave the computer off until the computer and DC IN indicator reaches room temperature, then turn it back on.
User's Manual T ROUBLESHOOTING 9-6 Battery If you suspect a problem with the battery, check the DC IN indicator as well as the Battery indicator. For information on indicator and battery operation see Chapter 6, Power and Power-Up Modes . Problem Procedure Battery doesn’t The battery may be discharged.
9-7 T ROUBLESHOOTING Hardware and system checklist Password Problem P rocedure Cannot enter Contact your dealer. or forgot password NOTE: For information on setting a password, refer to Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration.
User's Manual T ROUBLESHOOTING 9-8 • The way to replace the key-top Press the key-top until you hear a click after removing a metal spring from the key-top, hooking it to projecting parts and aligning the center of the key-top.
9-9 T ROUBLESHOOTING • Follow the steps below when a plastic spring is out of place together with a key- top. 1. Remove the plastic spring from the key-top. 2. Attach the plastic spring to the key board with its flat face downward after confirming the direction.
User's Manual T ROUBLESHOOTING 9-10 3. Press from the upside until you hear a click after replacing the key-top to the right position. LCD p anel Problem P rocedure No display Press hot keys Fn + F5 to change the display priority, to make sure it is not set for an external monitor.
9-11 T ROUBLESHOOTING Hard disk drive Problem P rocedure Computer does not Check if a diskette is in the diskette drive or a boot from hard disk CD-ROM is in the optical media drive. Remove drive any diskette and/or CD-ROM and check Boot priority. Refer to Chapter 7, Boot Priority .
User's Manual T ROUBLESHOOTING 9-12 A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner.
9-13 T ROUBLESHOOTING DVD-ROM drive For more information, refer to Chapter 4, Operating Basics . Problem P rocedure You cannot access Make sure the drive’s drawer is securely a CD/DVD in the drive closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.
User's Manual T ROUBLESHOOTING 9-14 Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: C D- D A, CD - Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD- EXTRA), CD-G (Audio CD only), Addressing Method 2 Check the region code on the DVD.
9-15 T ROUBLESHOOTING Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem.
User's Manual T ROUBLESHOOTING 9-16 Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording.
9-17 T ROUBLESHOOTING Some CD/DVDs The software or hardware configuration may run correctly, but be causing a problem. Make sure the others do not hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
User's Manual T ROUBLESHOOTING 9-18 Diskette drive For more information, refer to Chapter 4, Operating Basics . Problem Pr ocedure Drive does not There may be a faulty cable connection. Check operate the connection to the computer and to the drive.
9-19 T ROUBLESHOOTING Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation.
User's Manual T ROUBLESHOOTING 9-20 USB mouse Problem Pr ocedure On-screen pointer The system might be busy. If the pointer is does not respond to shaped as an hourglass, wait for it to resume mouse operation its normal shape and try again to move it.
9-21 T ROUBLESHOOTING USB Refer also to your USB device’s documentation. Problem P rocedure USB device does Check for a firm cable connection between the not work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed.
User's Manual T ROUBLESHOOTING 9-22 Sound system Refer also to documentation for your audio devices. Problem Pr ocedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure.
9-23 T ROUBLESHOOTING Modem Refer to the online help files for Appendix C and D . Problem P rocedure Communication Make sure the computer’s internal modem software can’t settings are correct. Refer to Phone and Modem initialize modem Properties in the Control Panel.
User's Manual T ROUBLESHOOTING 9-24 Character display In data transmission, make sure the parity bit becomes garbled and stop bit settings correspond with those during a of the remote computer. communication Check the flow control and communication protocol.
9-25 T ROUBLESHOOTING Wireless LAN If the following procedures do not restore LAN access, consult your LAN adminis- trator. For more information on wireless communication, refer to Chapter 4, Operat- ing Basics . Problem P rocedure Cannot access Make sure the computer’s wireless Wireless LAN communication switch is set to on.
User's Manual T ROUBLESHOOTING 9-26 China TOSHIBA Computer Systems (Shanghai) Co., Ltd. Bldg. 33, No. 351, Jinzang Road, Pudong New Area, Shanghai, P.
9-27 T ROUBLESHOOTING United States of America TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 USA In Europe Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany France TOSHIBA Systèms France S.
User's Manual T ROUBLESHOOTING 9-28.
A PPENDIXES Appendixes Appendix A Specifications ........................................................................... A - 1 Appendix B Display Controller and Modes .............................................. B - 1 Appendix C AT Commands ....
A PPENDIXES.
A PPENDIX A A-1 Appendix A S pecifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 332 (w) x 293 (d) x 33/40 (h) millimeters (not including parts that extend beyond the main body) Weight 2.
A PPENDIX A A-2 User's Manual Built-in Modem Network control unit (NCU) Type of NCU A A Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 co.
B-1 A PPENDIX B Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off.
User's Manual B-2 A PPENDIX B Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
B-3 A PPENDIX B Appendix B Table1 Video modes (VGA) continued Video Type Resolution Character L C D CRT Scanning mode matrix colors colors frequency (pels) Vertical (Hz) D VGA 320 x 200 8 x 8 16 of 25.
User's Manual B-4 A PPENDIX B Table 2 Video modes (XGA) Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 1.
B-5 A PPENDIX B Appendix B Table 2 Video modes (XGA) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100.
User's Manual B-6 A PPENDIX B Table 2 Video modes (XGA) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 16M/16M 16M/16M 6 0 75 85 100 800 x 600 16M/16M 16M/16M 6 0.
B-7 A PPENDIX B Table 3 Video modes (Super XGA+) Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 76.
User's Manual B-8 A PPENDIX B Table 3 Video modes (Super XGA+) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/6.
B-9 A PPENDIX B Appendix B Table 3 Video modes (Super XGA+) continued Resolution L C D C RT Vertical colors colors frequency (Hz) 640 x 480 16M/16M 16M/16M 6 0 75 85 100 800 x 600 16M/16M 16M/16M 6 0 .
User's Manual B-10 A PPENDIX B.
C-1 A PPENDIX C Appendix C A T Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software.
User's Manual C-2 A PPENDIX C A Answer command This command instructs the modem to go off-hook and answer an incoming call. B n Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps.
C-3 A PPENDIX C ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S = n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information).
User's Manual C-4 A PPENDIX C L n Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0 ) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode This command turns the speaker on or off.
C-5 A PPENDIX C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode.
User's Manual C-6 A PPENDIX C T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received.
C-7 A PPENDIX C X 5 Enable Enable O K , R I NG , NO CARRIER, ERROR, NODIAL TONE, BUSY , CONNECT <RA TE>, RRING , NO BONGTONE, DELA YED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The m odem dials a call regardless of whether it detects a dial tone.
User's Manual C-8 A PPENDIX C &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default).
C-9 A PPENDIX C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.
User's Manual C-10 A PPENDIX C &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE.
C-11 A PPENDIX C Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. N0 Buffer mode. No error control. N1 Direct mode. N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures.
User's Manual C-12 A PPENDIX C Vn Protocol result code V0 Disable protocol result code appended to DCE speed. V1 Enable protocol result code appended to DCE speed (default).
D-1 A PPENDIX D Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connec- tion fails.
User's Manual D-2 A PPENDIX D S 0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command.
D-3 A PPENDIX D S 4 Response formatting character (user defined) This register determines the ASCII value used as the line feed charac- ter. The modem uses a line feed character in command mode when it responds to the computer.
User's Manual D-4 A PPENDIX D S 7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (an- swer).
D-5 A PPENDIX D S3 7 Dial line rate S37 = 0 (default) maximum modem speed S37 = 1 r eserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 r eserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37.
User's Manual D-6 A PPENDIX D A T command set result codes The following table shows the result codes. The result code summary Result Code Numeric Description O K 0 Command executed CONNECT 1 Mod.
D-7 A PPENDIX D Result Code Numeric Description DELAYED* 2 8 8 Delay is in effect for the dialed number BLACKLISTED* 2 8 9 Dialed number is blacklisted BLACKLIST FULL* 2 9 0 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled.
User's Manual D-8 A PPENDIX D.
E-1 A PPENDIX E Appendix E V .90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.
User's Manual E-2 A PPENDIX E Table E-1 Result codes for a V.90 connection No. Result code Description 7 0 CONNECT 32000 EC* Connection at 32000 bps 7 2 CONNECT 36000 EC* Connection at 36000 bps .
E-3 A PPENDIX E * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.
User's Manual E-4 A PPENDIX E.
F-1 A PPENDIX F Appendix F Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described.
F-2 User's Manual A PPENDIX F 9 . Secure the cover with one screw. Removing the internal modem To remove the internal modem, follow the steps below. 1 . Save your data and turn off the computer. 2 . Disconnect the AC adaptor and any other peripheral device.
G-1 A PPENDIX G Appendix G Wireless LAN Card Specifications Form Factor - Mini PCI TypeIII Capability - I EEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.The 'Wi-Fi CERTIFIED' logo is a certification mark of the Wi-Fi Alliance.
G-2 User's Manual A PPENDIX G - Band2.4GHz (2400-2483.5 MHz) (Revision B) Modulation Technique - DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) - OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM- 64QAM (Revision A, Turbo Mode) The range of the wireless signal is related to the Transmit Rate of the wireless communication.
G-3 A PPENDIX G When installing Wireless LAN Cards, the channel configuration is managed as follows: ❑ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will .
G-4 User's Manual A PPENDIX G Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850 MHz Note Channel ID 42 5210 U S only *1 50 5250 U S only *1 58 5290 U S only *1 152 5760 U S only *1 16.
H-1 A PPENDIX H Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.
H-2 User's Manual A PPENDIX H The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
A PPENDIX I I-1 Appendix I Part s Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, ODD, and communication devices.
User’s Manual A PPENDIX I Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart.
Glossary-1 G LOSSARY Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP : accelerated graphi.
Glossary-2 G LOSSARY analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute.
Glossary-3 G LOSSARY B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system com- mands or executable files.
Glossary-4 G LOSSARY capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB.
Glossary-5 G LOSSARY components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instruc- tions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information.
Glossary-6 G LOSSARY device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information.
Glossary-7 G LOSSARY escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary-8 G LOSSARY computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F.
Glossary-9 G LOSSARY coating is etched into character forming segments with leads that extend to the edge of the glass. Applying a voltage between the glass sheets alters the brightness of the liquid crystal. LSI: Large Scale Integration. 1) A technology that allows the inclusion of up to 100,000 simple logic gates on a single chip.
Glossary-10 G LOSSARY permanently storing information. Turning the computer’s power off does not alter data stored in nonvola- tile memory. numeric keypad overlay: A feature that allows you to use certain keys on the keyboard to perform numeric entry, or to control cursor and page move- ment.
Glossary-11 G LOSSARY P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relation- ship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1.
Glossary-12 G LOSSARY S SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD cards: Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assis- tants.
Glossary-13 G LOSSARY subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels indepen- dently, each may emit a different degree of brightness. See also pixel. synchronous: Having a constant time interval between successive bits, characters or events.
Glossary-14 G LOSSARY Glossary.
Index Index-1 I NDEX Index location of vents 2-2 settings 4-24 CPU, See Processor D Diskette drive 1-3 using 4-2 view 2-10 Display 1-5, 2-7 automatic power off 1-8 brightness decrease 5-5 brightness i.
User's manual Index-2 I NDEX work habits 3-4 Expansion memory, See Memory F Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4 Fn.
Index Index-3 I NDEX L LAN 1-7 connecting 4-22 disconnecting 4-22 jack 2-5 LAN active indicator 2-4 link indicator 2-5 problems 9-24 LCD, See Display, Video modes and Monitor external Level 2 cache, S.
User's manual Index-4 I NDEX keyboard 9-7 LAN 9-24 LCD panel 9-10 memory expansion 9-21 modem 9-23 monitor external 9-22 mouse, USB 9-20 overheating power down 9-5 password 9-7 PC card 9-18 point.
Index Index-5 I NDEX Wireless LAN 1-7 problems 9-25 using 4-19.
An important point after buying a device Toshiba A10 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba A10 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba A10 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba A10 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba A10 Series will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba A10 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba A10 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba A10 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba A10 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
