Instruction/ maintenance manual of the product 19LV505C Toshiba
Go to page of 68
IIIustration of 19L V505C 4 14 21 40 43 56 Introduction Connections Basic setup Basic playback Advanced playback Function setup 62 Others 26 TV operation ©2008 T oshiba Corporation Before operating the unit, please read this manual thoroughly . *Screen size is approximate.
Introduction 2 Dear Customer , Thank you for purchasing this T oshiba L CD T V or T V/ DVD Combination television. This manual will help you use the many exciting features of your new L C D T V . Before operating your L CD T V or TV/ DVD Combination, please read this manual completely , and keep it nearby for future reference.
Introduction 3 Location of the required Marking The rating sheet and the safety caution are the rear of the unit. CERTIFICA TION: COMPLIES WITH FDA RADIA TION PERFORMANCE ST ANDARDS, 21 CFR SUBCHAPTER J. CAUTION: THIS DIGIT AL VIDEO PLA YER EMPLOYS A LASER SYSTEM.
Introduction 4 SAFETY INSTRUCTIONS 15) T o avoid damage to this product, never place or store the TV in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration.
Introduction 5 Antenna discharge unit (NEC Section 810-20) Antenna lead-in wire Grounding conductors (NEC Section 810-21) Ground clamps Power service grounding electrode system (NEC Art 250 Part H) Ground clamp Electric service equipment Installation (cont.
Introduction 6 Precautions Choosing a location for your LCD TV ■ Retractable pedestal stand and locating the LCD TV Observe the following safety precautions: 1) Ensure that unpacking and transfer of the unit is carried out by two or more people. 2) Put the LCD TV on a large level area in a recumbent posture.
7 Introduction On handling discs Do not touch the playback side of the disc. For example, handle the disc so that it is shown in fi gure below. Do not attach paper or tape to discs. On cleaning discs Fingerprints and dust on the disc cause picture and sound deterioration.
8 Introduction Playable discs This unit can play the following discs. • Y ou cannot play discs other than those listed above. • Y ou cannot play discs of DVD-RAM, DVD-ROM, CD- ROM, Photo CD, etc., or non standardized discs even if they may be labeled as above.
9 Introduction Contents Introduction SAFETY INSTRUCTIONS ................................ 4 Precautions....................................................... 6 Notes on discs .................................................. 7 Contents .............
10 Introduction Identification of controls Speaker Front POWER indicator 21 Remote sensor 13 Side Left Side Disc slot 40 EJECT button 41 CHANNEL 26 PLA Y button 40 VOLUME (+/–) buttons 26 CHANNEL 26.
11 Introduction Rear AC INPUT 20 HEAD PHONE jack 27 COLORSTREAM HD IN jacks 17 VIDEO/GAME IN jack 16 17 PC MONITOR IN jack 20 PC AUDIO IN jack 20 HDMI IN jack 19 COAXIAL DIGIT AL AUDIO OUT jack 18 19 Antenna jack 14 15 Illustration of 19L V505C 50S0301A.
12 Introduction SLOW ( ) button Direction buttons ( / / / ) EJECT button 41 DISPLA Y button Numbered buttons (0 - 9) 49 27 60 SUBTITLE button 48 INPUT button 16 ZOOM button 43 MENU button 22 SETUP but.
13 Introduction Replace the compartment cover . Install two “R03/AAA” batteries (supplied), paying attention to the polarity indicated in the battery compartment. Open the battery compartment cover in the direction of the arrow . 1 23 • Aim the remote control at the remote sensor and press control buttons to operate.
Connections 14 75 ohm coaxial cable (not supplied) 300-75 ohm matching transformer (not supplied) 300-75 ohm matching transformer (not supplied) UHF 300 ohm twin-lead wire (not supplied) VHF 300 ohm t.
Connections 15 For basic cable service not requiring a converter/descrambler box, connect the Cable TV 75 ohm coaxial cable directly to the Antenna jack on the back of the TV/DVD.
Connections 16 T o playback from the VCR, connect the VCR to the TV/DVD as shown. Select the “Video” by pressing INPUT repeatedly . Y ou can enjoy playing a TV game on the screen by adjusting to the suitable brightness for your eyes. 1. Connect a TV Game to the TV/DVD.
Connections 17 Connecting to an optional equipment with S-video output If you connect a VCR with an S-Video cable to the S-VIDEO IN jack on the left side of the TV/DVD, you must also connect the audio cables to the AUDIO IN jacks as shown below . The S-Video cable only carries the video signal.
Connections 18 Dolby Digital Dolby Digital is the surround sound technology used in theaters showing the latest movies, and is now available to reproduce this realistic effect in the home.
Connections 19 Ampli fi er equipped with a Digital audio input T o COAXIAL type digital audio input 75 Ω coaxial cable (not supplied) Connecting to an ampli fi er equipped with a digital audio inpu.
Connections Connecting to optional equipment (Continued)/ Power source Connections 20 Power source Note: Nev er connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only . If the polarized A C cord does not fit into a non-polarized A C outlet, do not attempt to file or cut the blade.
21 Basic setup Basic setup Auto Setup Auto Setup The Auto Setup function helps to install your TV/DVD easily . It leads you the Language selection, Air/Cable selection and Automatic channel search. IMPORT ANT : Make sure that the antenna or cable TV system connection is made! POWER EXIT/CANCEL / / / ENTER 1 T o turn on the TV/D VD , press POWER.
22 Basic setup Setting the language Setting the language This TV/DVD can display the on screen language in English, French or Spanish. Select the language you prefer fi rst, then proceed with the other menu options. EXIT/CANCEL 1 T o turn on the TV/D VD , press POWER.
23 Basic setup / / / T o memorize channels This TV/DVD is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory , skipping over unwanted channels. Before selecting channels, they must be programmed into the TV/DVD ʼ s memory .
24 Basic setup Add/Delete channel Y ou can select the channel that you w ant to skip. 1 Press MENU in the TV mode. Press ▲ or ▼ to select “Channel”, then pr ess ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “ Add/Delete”, then press ▶ or ENTER.
25 Basic setup Adding Channel If you find a ne w channel unregistered, y ou can add the new channel into the channel memory . 1 T une in the new channel.
26 TV operation 1 T o turn on the TV/D VD , press POWER . (POWER indicator on the fr ont of the unit changes green. It may tak e approx. 10 seconds for a picture to appear on screen.) 2 Adjust the v olume lev el by pressing VO L + or – . The volume le vel will be indicated on the screen by or ange bars.
27 TV operation TV operation (continued) ■ DISPLA Y Press DISPLA Y to display the current inf ormation on the screen. When the TV/DVD receiv es a digital signal, the digital information will appear .
28 Labeling channels 1 Press MENU in the TV mode. Press then press ▲ or ▼ to select “Channel” menu, then press ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “Ch Label”, then press ▶ or ENTER.
TV operation 29 Labeling video inputs The Video Label feature allow s you to label each input sour ce for y our TV/DVD . / / / MENU EXIT/CANCEL ENTER Labeling video inputs 1 Press MENU in the TV mode. Press ▲ or ▼ to select “Setup”, then pr ess ▶ or ENTER.
TV operation 30 4 Press ▲ or ▼ to select “ Analog Caption” or “Digital Caption”, then press ◀ or ▶ to select the desired Closed Caption mode . When you select “ Analog Caption”, you can choose C1, C2, C3, C4, T1, T2, T3 and T4. When you select “Digital Caption”, you can choose from CS1, CS2, CS3, CS4, CS5 and CS6.
TV operation CC advanced 1 Press MENU in the TV mode. Press ▲ or ▼ to select “Setup”, then pr ess ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “Closed Caption”, then press ▶ or ENTER.
32 TV operation Adjusting the picture preference 1 Press MENU in the TV mode. Press ▲ or ▼ to select “Pictur e”, then press ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “Picture Prefer ence”.
33 TV operation Viewing the wide-screen picture formats 1 Press MENU . Press ▲ or ▼ to select “Picture”, then press ▶ or ENTER. 2 Press ▲ or ▼ to select “Picture Size”, then press ▶ or ENTER to displa y Picture Size menu.
34 TV operation 1 Press MENU in the TV mode. Then press ▲ or ▼ to select “Pictur e”, then press ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “DNR”.
35 TV operation 1 Press INPUT , then press ▲ / ▼ or 4 to select the PC mode. 2 Press MENU . Then press ▲ or ▼ to select “Picture”, then press ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 3 Press ▲ or ▼ to select “PC Setting”, then press ▶ or ENTER.
36 TV operation 1 Press MENU in the TV mode. Press ▲ or ▼ to select “ Audio”, then press ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “MTS”, then press ◀ or ▶ to select “Ster eo”.
37 TV operation 1 Press MENU in the TV mode. Then press ▲ or ▼ to select “ Audio” , then press ▶ or ENTER. Picture Audio Channel Setup Main Menu : Select ENTER:Set 2 Press ▲ or ▼ to select “ Audio Language”, then press ▶ or ENTER to displa y the Audio Language menu.
38 TV operation Using the aspect feature/ Adjusting the back lighting When the Aspect feature is set to On and the TV receives a 480i signal, the picture size is automatically selected (as described in the f ollowing table). The Backlight feature adjusts the scr een brightness for impr ov ed picture clarity .
39 TV operation Resetting your settings Setting the Auto Shut Off Setting the Auto Shut Off/ Resetting your settings If the Auto Shut Off featur e is On, a station being view ed stops broadcasting and the TV is not operated, the TV will automatically shut itself off after 15 minutes.
40 Basic playback Press STOP to end playback. ■ Resuming facility • The unit records the stopped point, depending on the disc. “ ” appears on the screen. Press PLA Y to resume playback (from the scene point). • If you press STOP again (“ ■ ” appears on the TV screen), the unit will clear the stopped point.
Basic playback 41 T o pause playback (still mode) Press P AUSE during playback. T o resume normal playback, press PLA Y . • The sound is muted during still mode. T o stop playback Press STOP . T o remove the disc Press EJECT . Remove the disc after the disc comes out.
42 Basic playback Playing frame by frame Playing in fast reverse or fast forward directions Press REV or FF during playback. REV : Fast reverse playback FF : Fast forward playback Each time you press REV or FF button, the playback speed changes. T o resume normal playback Press PLA Y .
43 Advanced playback Advanced playback Press / / / to view a different part of the frame. Y ou may move the frame from the center position to UP , DOWN, LEFT or RIGHT direction. In the zoom mode, press ZOOM repeatedly to return to a 1:1 view ( Off). Zooming Press ZOOM during playback.
Advanced playback 44 Press MARKER during playback. Select the blank Marker using or . Then press ENTER to mark the desired scene. • Repeat this procedure to mark the other 2 scenes. Marking desired scenes The unit stores the points that you want to watch again up to 3 points.
45 Advanced playback Press REPEA T A-B during playback. The start point is selected. Press REPEA T A-B again. The end point is selected. Playback starts at the point that you selected. Playback stops at the end point and returns to point A automatically , then starts again.
Advanced playback 46 3 2 VCD CD 1 1 2 Press / to return to the left column, then press / to select the “Program Playback” and press ENTER. The programs you selected will start to playback in order . • T o resume normal playback, select Mode: “Off” in step 2.
47 Advanced playback Changing angles Title selection DVD menu Press ANGLE during playback. The current angle will appear . When playing back a disc recorded with multi-angle facility , you can change the angle that you are viewing the scene from. 1 Press ANGLE repeatedly until the desired angle is selected.
Advanced playback 48 Press SUBTITLE repeatedly during playback until the desired language is selected. Press AUDIO SELECT repeatedly until the desired language is selected. • The on screen display will disappear after a few seconds. Press AUDIO SELECT during playback.
49 Advanced playback Disc status/T o turn off the PBC DVD VCD Disc status With press of DISPLA Y , the status of the disc will appear on the screen. T o cancel the display , press DISPLA Y again. DVD DVD 00:15:25 01:41:39 Title 1/3 Chapter 2/24 1/1 Eng Dolby Digital 1/2 Eng 1/1 DISC OPERA TION ELAPSED TIME TOT AL TIME TITLE NO.
Advanced playback 50 MP3/WMA/JPEG/DivX ® and Audio CD operation Audio CD/MP3/WMA/JPEG/DivX ® CD information Limitations on MP3/WMA/JPEG/DivX ® CD playback • MP3/WMA/JPEG/DivX ® CD is the disc that is standardized by ISO9660, its fi le name must include 3-digits extension letters, “.
Advanced playback 51 MP3/WMA and Audio CD playback CD Load an Audio CD or a disc on which MP3 or WMA fi les have been recorded in the disc slot. 1 A fi le browser screen will appear on the screen.
Advanced playback 52 MP3/WMA/JPEG/DivX ® and Audio CD operation (Continued) The slide show enables you to view pictures ( fi les) one after another automatically . Preparation: • Set “JPEG Interval” setting to “5 Seconds”, “10 Seconds” or “15 Seconds” 59 .
Advanced playback 53 Load a disc on which DivX ® fi les have been recorded in the disc slot. 1 A fi le browser screen will appear on the TV screen. 2 Press / to select fi le. 3 Press ENTER or PLA Y . The selected DivX ® movie will be played back on the TV screen.
Advanced playback 54 Repeat, random and program playback using file browser Press PLA Y . The random playback will start. CD CD F older-1 F older-2 M P3-1 M P3-2 MP3-3 Select Files Repeat :Off Mode :O.
Advanced playback 55 JPEG Preview Edit Mode Browser View Clear Program MP3-1 MP3-2 MP3-3 WMA-3 In the fi le browser , press / / / to select “Edit Mode”, then press ENTER. Press / / / to select fi le you want to add into the program list. Press / / / to select “Add T o Program”.
Function setup 56 • Repeat steps 3, 4 and 5 to change other option. • T o select another section, go back to step 2 by pressing repeatedly . Customizing the function settings Y ou can change the default settings of the DVD mode to customize performance to your preference.
Function setup 57 Section Option Details Page Menu Subtitle Audio T o select the language of “Menu”, “Subtitle” and “Audio” if more than one language are available on the disc. 58 TV Screen T o select a picture size according to the aspect ratio of your TV .
Function setup 58 Setting details Menu, Subtitle, Audio Y ou can select the language of “Menu”, “Subtitle” and “Audio” if more than one languages are recorded onto the disc. English, Francais, Espanol: The selected language will be heard or seen.
Function setup 59 Picture Mode There are two types of source content in pictures recorded in DVD video discs: fi lm content (pictures recorded from fi lms at 24 frames per second) and video content (video signals recorded at 30 frames per second). Make this selection according to the type of content being viewed.
Function setup 60 DRC : Off QSound : On Menu : English Subtitle : English Audio : English E.B.L. : Off TV Screen : 4:3 Display : On Picture Mode : Auto JPEG Interval : 5 Seconds Screen Saver : On Parental : Off Password : Change DivX(R) VOD : Display Parental control setting Some discs are speci fi ed as not suitable for children.
Function setup 61 Enter the password with Number buttons (0–9). Then press ENTER. If the DVD disc has been designed to temporarily cancel the Rating level, the screen which follows the “Reading” screen will change, depending on which disc is played.
Others SYMPTOMS POSSIBLE SOLUTIONS P AGE POWER TV/DVD does not operate. • Make sure the connection of AC cord is secured. • T ry another AC outlet. • Unplug unit, then plug it back in. 20 TV BROADCAST RECEPTION Poor sound or No sound. • Station or Cable TV may have problems, try another station.
Others SYMPTOMS POSSIBLE SOLUTIONS P AGE DVD Playback doesn ʼ t start. • No disc is loaded. • The disc may be dirty . Clean up the disc. • The unit cannot play CD-ROMs, etc. 40 7 8 No picture. • TV/DVD selector is not set correctly . 40 No sound.
Others GHOSTS Ghosts are caused by the television signal following two paths. One is the direct path and the other is re fl ected by tall buildings, hills or other large objects. Changing the direction or position of the antenna may improve the reception.
Others Language Name Code Language Name Code Language Name Code Language Name Code Abkhazian 1 1 12 Fiji 1620 Lingala 2224 Singhalese 2919 Afar 1111 Finnish 1619 Lithuanian 2230 Slovak 2921 Afrikaans .
Others 66 Specifications Model 19L V505C 22L V505C General Power supply AC 120V 60Hz Power consumption Operation: 60 W , Stand by: 1 W Operation: 65 W , Stand by: 1 W Weight 1 1.2 lbs (5.1 kg) 13.5 lbs (6.1 kg) Dimensions Width: 18-9/16 inches (472 mm) Height: 15-13/16 inches (401 mm) Depth: 8-1/8 inches (207 mm) Width: 21-1/8 inches (536.
Others 67 Limited Canadian W arranty for T oshiba Brand Flat Panel T elevisions T oshiba of Canada Limited (“ TCL ”) makes the following limited warranties to original consumers in Canada.
Disclaimer and Limitation of Remedy TO THE EXTENT NOT PRECLUDED BY LA W, ALL OTHER EXPRESS AND IMPLIED W ARRANTIES, CONDITIONS AND REPRESENT A TIONS FOR THIS TELEVISION, INCLUDING THE IMPLIED W ARRANTIES, CONDITIONS AND REPRESENT A TIONS OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE, ARE HEREBY DISCLAIMED AND EXCLUDED.
An important point after buying a device Toshiba 19LV505C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Toshiba 19LV505C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Toshiba 19LV505C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Toshiba 19LV505C you will learn all the available features of the product, as well as information on its operation. The information that you get Toshiba 19LV505C will certainly help you make a decision on the purchase.
If you already are a holder of Toshiba 19LV505C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Toshiba 19LV505C.
However, one of the most important roles played by the user manual is to help in solving problems with Toshiba 19LV505C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Toshiba 19LV505C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
