Instruction/ maintenance manual of the product SP-400 Top Innovations
Go to page of 9
Top Innovations, Inc. Innovative Products to Make Your Life Easier Model SP - 400 Owner ’ s Manual ¾ Sews Durable Chain Stitch ¾ Compact Size for Emergency Repairs ¾ Pre - Threaded and Ready to Use Top Innovations, Inc. 400 NW Platte Valley Drive Riverside, MO 64150 (800) 711 - 6617 (816) 584 - 9700 Fax:(816) 584 - 9066 www.
3 PARTS AND ACCESSORIES Includes the Following Accessories: ¾ 5 Mini Spools of Thread in Assorted Colors ¾ Seam Ripper/Thread Trimmer ¾ Needle Threader ¾ Extra #14 Needle * Batteries Not Included 4 NOTE: Even if you have sewn bef ore, these instructions will make your first use much easier! TABLE OF CONTENTS P AGE Welcome Letter .
5 IMPORTANT SAFEGUARDS ¾ When Threading or changing a needle, always unplug the power supply ¾ Work carefully and watch the sewing area to avoid the needle during operation ¾ Do not pull the fabric.
7 3. Pull at least 2 inches of thread tail through the needle prior to starting to sew. 4. Hold HandyMender in right hand; press power switch with your thumb; use your left hand to guide the fabric . 5. When pivoting or turning a corner, the needle must be lowered into the fabric.
9 6. Tie off the seam as follows: a. Pass Threader through the last stitch. b. Place the thread into Threader. c. Pull out about 1 inch. d. Slip the thread through the loop and pull it tight to finish the seam. 10 How to Thread the HandyMender Thread the HandyMender following the numbers as shown below.
11 To Install the Normal Thread Spool 1. Loosen the Bobbin Nut and take off Bobbin. 2. Connect the Spool Pin on Bobbin Shaft. 3. Slip thread spool on spool pin. 4. Put the white Spool Cap on the Spool Pin to secure the thread spool. Replacing the Needle 1.
13 Thread Comes Out Of Tension Control While Sewing Check that flow of thread from bobbin or spool is correct. ( See page 1 0 ) Handy Mender Does Not Run Or Runs Slowly After Pressing Power Sw itch (1) Check power connection. (2) Check if batteries are installed correctly.
15 LIMITED WARRANTY Top Innovations, Inc. will repair or replace, at its option, without charge to the consumer any SEW PRO product that fails due to a defect in material or workmanship within 90 days following the initial consumer purchase. This warranty does not cover damage caused by commercial use, misuse, alteration, or modification.
17 Printed in China Top Innovations, Inc. 400 NW Platte Valley Drive • Riverside, MO 64150 (800) 711 - 6617 (816) 584 - 9700 Fax:(816) 584 - 9066 www.
An important point after buying a device Top Innovations SP-400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Top Innovations SP-400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Top Innovations SP-400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Top Innovations SP-400 you will learn all the available features of the product, as well as information on its operation. The information that you get Top Innovations SP-400 will certainly help you make a decision on the purchase.
If you already are a holder of Top Innovations SP-400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Top Innovations SP-400.
However, one of the most important roles played by the user manual is to help in solving problems with Top Innovations SP-400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Top Innovations SP-400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
