Instruction/ maintenance manual of the product N-CC2360 TOA Electronics
Go to page of 20
NETWORK COLOR CAMERA N-CC2360 INSTRUCTION MANUAL 1. SAFETY PRECAUTIONS .......................... 2 2. LIST OF INCLUDED COMPONENTS AND PARTS ............ 3 3. GENERAL DESCRIPTION ........................ 4 4. HANDLING PRECAUTIONS .....................
2 1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety.
3 Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. CAUTION When Installing the Unit • Avoid installing the.
4 3. GENERAL DESCRIPTION 4. HANDLING PRECAUTIONS • Do not direct the camera lens to the sun or strong lighting or light reflection. Exposure to direct sunlight could cause the CCD's color filter to deteriorate, leading to image discoloration. • Do not give the camera a great shock or vibration, as this will damage the camera.
5 (1) Power Input Terminal [24 V AC, 24 V DC] Connect this terminal to the 24 V AC or 24 V DC power supply. Note Do not connect 24 V AC or 24 V DC power when using a PoE-compatible hub. (2) Indicators [RDY BUSY ERR] RDY (green): Remains lit during normal operation.
6 Ceiling surface Lock lever Camera mounting bracket (optional) Pedestal Camera mount Camera mount Pedestal Camera mounting bracket (optional) Lock lever Camera mounting bracket (optional) W all surface W all surface LENS 1 3 2 4 Lens connector 1 2 3 4 Lens connector pin No.
7 6mm or less Lens • To avoid damaging the internal sections of the camera's lens mount, be sure that the lens flange is 6 mm or less thick as illustrated on the right. • C-mount lenses must be used in conjunction with the Lens Mounting Adapter CF-5 (optional).
8 7.1. Connection Example PoE compatible HUB Software Decorder 10BASE-T/ 100BASE-TX 10BASE-T/ 100BASE-TX 24V 2 1 24V 12C12C 10/100M PoE AUDIO OUT MONITOR OUT OUT IN CONT ACT RDY BUSY ERR FD/COL LINK /.
9 8. ADJUSTMENT 1. The RDY indicator lights when the power is supplied to the network camera. 2. Connect the monitor output terminal to the monitor so that the picture may be displayed on the monitor. 3. Set the Flicker-reduction switch of the mode switch to "ON" position if flicker is annoying.
10 6. Adjust the iris level • When using the DC input type lens Adjust the iris level on the Camera menu screen's "IRIS" item. 6-1 Check to confirm that Camera menu setting items are selected as follows.
11 F. A D J ANTI - FLICKER NC OFF ON Mode switch Focus adjustment switch Flicker-reduction switch Not used. Mode switch ( factory default ) [ N-CC2360 ] F. A D J ANTI-FLICKER NC ON OFF INITIALIZE RESET OFF ON OFF ON OFF ON OFF ON 9. ABOUT THE MODE SWITCH Set each switch to the position that provides the best picture reproduction.
12 No. 1 2 3 4 5 6 IN 1 IN 2 C OUT 1 OUT 2 C Contact input 1 Contact input 2 COM Contact output 1 Contact output 2 COM T erminal Name Contact name Day/ Night Select Contact input 1 or Contact input 2.
13 1 1. SETTING INITIALIZA TION Network settings can be reset to their factory defaults. 1. Either press the Reset key or switch on the power again while holding down the INITIALIZE key. 2. Continue to press the INITIALIZE key until the Ready indicator has switched from flashing to steady-on mode.
14 12. TROUBLESHOOTING Remedy Supply power independently to the Camera. Confirm that the cable type (category, null modem or straight) is appropriate for the connected port, then connect correctly. If the rough noise is annoying and distracting, lower the AGC level.
15 24 V AC, 50/60 Hz or 24 V DC or PoE (IEEE802.3af) 13 W (at 24 V AC), (8 W: PoE, 350mA: 24 V DC) Screwless connector (Solid cable: ø 0.4– ø 1.2 mm (AWG 26 – 16), Stranded cable: 0.
16 Note: The design and specification are subject to change without notice for improvement. MPEG-4: max. 4 Mbps 5 (MPEG-4: 4, JPEG: 1) In streaming mode: No limit (MPEG-4 only) Password authentication.
17 24 V AC, 50/60 Hz or 24 V DC or PoE (IEEE802.3af) 13 W (at 24 V AC), (8 W: PoE, 350mA: 24 V DC) Screwless connector (Solid cable: ø 0.4– ø 1.2 mm (AWG 26 – 16), Stranded cable: 0.
18 Note: The design and specification are subject to change without notice for improvement. MPEG-4: max. 4 Mbps 5 (MPEG-4: 4, JPEG: 1) In streaming mode: No limit (MPEG-4 only) Password authentication.
19.
133-12-993-90 URL: http://www.toa.jp/.
An important point after buying a device TOA Electronics N-CC2360 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics N-CC2360 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics N-CC2360 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics N-CC2360 you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics N-CC2360 will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics N-CC2360, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics N-CC2360.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics N-CC2360. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics N-CC2360 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
