Instruction/ maintenance manual of the product CST-38 TOA Electronics
Go to page of 24
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1 36" Wood Burning Fireplaces P/N 700,023M REV. C 06/2005 CST -38 CPF-38 MODELS CUSTOM SERIES This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace system.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 2 IMPORTANT: PLEASE READ AND UNDERSTAND THESE RULES TO FOLLOW FOR SAFETY. 1. Before starting your fireplace installation, read these installation instructions carefully to be sure you understand them completely and in entirety.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3 Figure 1 TYPICAL INSTALLATION *Construction Materials: • framing materials • paneling • particle board • flooring • millboard • dry wall • plywood • etc. PRECAUTIONS Note: These fireplace systems are not difficult to install.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 4 For questions, please call your distributor or the manufacturer. Special restrictions apply to the front and facing of the fireplace and nearby walls (See pages 18, 19 and 20 ). CHIMNEY SYSTEM These fireplaces are designed and code listed for use with Security Chimneys FTF8 chimney System only.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 5 Figure 7 Figure 6 Carefully consider the position of the fireplace opening with respect to the location of adja- cent or nearby stairwells, bath or k.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 6 The safety strips should extend in front and sides of the fireplace opening 2" (51 mm) . In the event a wooden support is used to elevate the fi.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 7 FIREPLACE SPECIFICATIONS Figure 15 39 ¹⁄₄ " (997 mm) 23 ¹⁵⁄₁₆ " (608 mm) 25 ³⁄₁₆ " (640 mm) 8" (203 mm) Left.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 8 Figure 16 Figure 19 CPF CST Figure 17 Figure 18 Figure 21 CST - Front View CST - End View CPF - Right Front View CPF - End View FRAMING SPECIFICATIONS Figure 20 7" Min.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 9 Figure 22 FRAMING WALL VARIATIONS As many as six (6) different framed wall con- figurations can be constructed to enclose the CST and CPF fireplaces. The following illustra- tions depict these variations of wall enclosures.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 10 A minimum 2" (51 mm) air space must be reserved for all combustible materials extend- ing for any continuous length surrounding the chimney. Reference Figures 24 and 25 and charts “Fram- ing Dimensions for Ceiling and Roof” on page 8, which specify minimum ceiling and roof dimensions.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 11 Check vertical alignment of chimney pipe so that it projects from the roof in a true vertical position. Security's chimney sections do not need to be screwed together. Additional rein- forcement is not necessary, except in certain offset conditions (see to page 16, Figure 47 ).
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 12 Figure 40 Step 10. Using an FTF8-CTD Round Termi- nation: 1. Hold FTF8-CTD over top of last chimney section ( Figure 40 ). 2. Center inner slip section in inner flue pipe- slip down. 3. Center outer locking section over outer flue pipe.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 13 Figure 41 TEN FOOT RULE SUMMARY The minimum chimney height above the roof and/or to adjacent walls and buildings is speci- fied by all major building codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 14 11 0 11 1 0 0 0 279 0.28 17 1 5 0 1 0 0 432 0.43 21 ¹⁄₄ 19 ¹⁄₄ 2 0 0 0 540 0.54 27 ¹⁄₄ 23 ¹⁄₄ 1 1 0 0 692 0.69 35 2 11 0 0 1 0 889 0.89 47 3 11 0 0 0 1 1194 1.19 51 ¹⁄₄ 43 ¹⁄₄ 0 1 1 0 1302 1.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 15 A B FTF8-ES30 Number of FTF8 A B Offset Height Offset/Return FTF8-S4 Chimney Sections Offset Height (Inches) (Inches) Elbow Set Stabilizer 12" .
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 16 OFFSET ELBOW ASSEMBLY Offset elbows install the same as chimney sections. First, snap the inner section INTO the preceding inner section of flue. Check connec- tion by pulling up slightly to ensure a tight fit.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 17 There is a one-hand operated shut-off valve located in the enclosed corner of the fireplace opening behind the screen.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 18 GAS LINE INSTALLATION The CST and CPF fireplaces have been ap- proved to accept a ¹⁄₂ " (13 mm) gas line for an approved gas appliance. Always have the appli- ance installed by a qualified, licensed plumber in accordance with all local building codes.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 19 If there is a continuous perpendicular side wall closer than 18" (mm) from the CST-38 fireplace opening, it must be protected with a 40 x 40&qu.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 20 Example: Given that the required “R value” for a suitable hearth extension used must be equal to or greater than: “R” = r x T L = 1.19 x 1 " = 1.19. If it is desired to elevate a marble hearth exten- sion to a level of 5" or more above the floor surface.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 21 ACCESSORIES AND COMPONENTS 63L10 FTF8-12 63L13 FTF8-18 63L14 FTF8-36 Chimney Section 63L15 FTF8-48 Canadian (Outside) 62L92 FTF8-18C Chimney Section.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 22 Combustion Air Kit 011761 AK-4 (Less Duct) 011763 AK-4LD “All-Glass TM ” 38AEP Aluminum End Panel 38AEP-BB “All-Glass TM ” Cabinet Doors 38T.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 23.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 24 Printed in U.S.A. © 2001 by LENNOX HEARTH PRODUCTS P/N 700,023M REV. C 06/2005 The manufacturer reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
An important point after buying a device TOA Electronics CST-38 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics CST-38 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics CST-38 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics CST-38 you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics CST-38 will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics CST-38, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics CST-38.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics CST-38. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics CST-38 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
