Instruction/ maintenance manual of the product 6D TOA Electronics
Go to page of 10
6481 0412 6481 0414 Tannoy adopts a policy of continuous improvement and product specification is subject to change. Tannoy United Kingdom T: +44 (0) 1236 420199 F: +44 (0) 1236 428230 E: enquiries@tannoy.com Tannoy North America T: (519) 745 1158 F: (519) 745 2364 E: inquiries@tannoyna.
2 3 1.0: IMPORTANT SAFETY INSTRUCTIONS 1.1 Introduction 2.0: THE BASICS 2.1 Unpacking and visual checks 2.2 Preliminary recommendation 3.0: PRECISION D SERIES FEATURES 3.1 Analog Input 3.2 Digital SPDIF Input 3.3 Connecting your speakers 3.4 User Controls 4.
4 5 Tannoy’s core technology, the Dual Concentric ™ is unlike ordinary drive units in that it is effectively two drivers, properly merged into one. The high-frequency unit is positioned on the back of the low frequency driver so that they are on the same axis.
6 7 An A/V 80Hz high pass filter switch provides instant conversion to 5.1 and higher order systems where a separate subwoofer below 80Hz is required. Filter characteristics are according to the international standards for this setup. This response is also shown diagramatically in Figure 1.
8 9 Low Mid Contour Frequency: A shelving filter can be set to the flat anechoic response or set to shelve at frequencies of 800Hz, 400Hz, or 200Hz in combination with the low mid contour amplitude (below) to correct half space (pi/2), quarter space (pi/4) and very difficult close field boundary conditions (pi/8 space).
10 11 Hi-Mid Shelf Boost/Cut: a shelving filter between 1kHz and 3KHz can be set to +2, +1dB, flat, -1dB, -2dB, to take account of room characteristics and personal preference. Editing news broadcast material is often easier with an increased output in this band.
12 13 1 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 -10dB +10dB 0dB re 2.8v @ 1 metre Quarter Space (Pi): An example of quarter space would be with speakers mounted on stands in a corner, or on the meter bridge against a wall or mounted on small stands or shelves against a wall.
14 15 MID AND HIGH EQ SETTINGS RT60 Decay Time: An estimation of the RT60 decay time above 1kHz within the monitoring environment will help to set the mid and high frequency equalisation.
16 17 8.0: TECHNICAL SPECIFICATIONS Frequency response (1) Maximum SPL (2) Distortion Dispersion (@-6dB) Drive unit LF/MID Dual Concentric ™ HF SuperTweeter ™ Shielded SYSTEM 59Hz – 51 kHz 116dB <0.
18 19 11.0: WARRANTY NO MAINTENANCE OF THE PRECISION 6D & 8D MONITORS IS NECESSARY. All components are guaranteed for a period of one year from the date of manufacture, subject to the absence of, or evidence of, misuse, overload or accidental damage.
An important point after buying a device TOA Electronics 6D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics 6D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics 6D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics 6D you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics 6D will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics 6D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics 6D.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics 6D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics 6D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
