Instruction/ maintenance manual of the product 110SR TOA Electronics
Go to page of 16
110 SERIES SUBWOOFERS 1 10TB (T ile Bridge) 1 10SR (Sheet Rock) OWNER’S MANUAL 1 10 Series Subwoofer.
CONTENTS T ABLE OF CONTENTS W ARRANTY / DAMAGE CLAIM 1 10 SEROES SUBWOOFERS & INPUT MODULES Cabinet Options INPUT MODULE OPTIONS Passive LO Pass Filter Passive 70 V olt INPUT MODULE OPTIONS Passiv.
WARRANTY / DAMAGE CLAIMS Congratulations on the purchase of your T annoy 1 10 Series Subwoofer . No regular maintenance of the subwoofer is necessary .
110 SERIES SUBWOOFERS AND INPUT MODULES This manual is intended for the owner , operator or installer of T annoy 1 10 Series Subwoofers. It is a guide for installing, setting up and operating the 1 10 Series in accordance with established codes and practices available at the time of publication .
INPUT MODULE OPTIONS P ASSIVE (ST ANDARD) The basic connection panel supplied with any of the 1 10 Series Subwoofers is a 6 Ohm speaker level input via barrier strip. It is highly recommended that the audio signal be lo pass filtered via an outboard active crossover .
INPUT MODULE OPTIONS P ASSIVE 70 VOL T WITH LO P ASS FIL TER P ASSIVE 1 10 INPUT MODULE SPKR LEVEL INPUT 70V 150W MADE IN CANADA OUTPUT CROSSOVER LO P ASS FIL TER L O-P ASS 100Hz ACTIVE (ACTIVE SUBWOOFER WITH 2-CHANNEL FEED-THROUGH) A dedicated power amplifier that really brings your 1 10 Series Subwoofer to life.
ACTIVE 110 INPUT MODULE CONTROLS ACTIVE MODULE WITH OUTPUT FOR 2 SPEAKERS 12 3 4 5 6 7 8 9 ACTIVE INPUT MODULE CONTROLS 1) INPUT - T wo channel (stereo) balanced line level input. Connect via XLR male plugs from your signal source.Use high quality 2 conductor shielded audio cable ( Belden 8451) for runs of up to 200’.
MECHANICAL INST ALLA TION 1 10TB NEW / EXISTING CONSTRUCTION INST ALLA TION PROCEDURES: Before you begin: Please read and understand all of these instructions thoroughly before beginning any work. Note that construction work for the installation of all T annoy products must be done to local building codes by qualified, licensed installers.
MECHANICAL INST ALLA TION 1 10TB 2’ x 2’ T ile grid installation procedures: 1) The 1 10TB was designed for quick and simple installation directly into a 2’ x 2’ T -bar ceiling grid (Figs. 9 & 10). 2) Remove several tiles around the installation location to gain easier access for placing the subwoofer in the ceiling grid.
MECHANICAL INST ALLA TION 1 10TB Fig. 8: Wire rope detailing suspension or seismic tether . Fig. 9: Installed subwoofer top view , only two chains attached. Fig. 10: Completed subwoofer installation. Fig. 1 1: Installing the hanger bolt. Fig. 12: Installed hanger bolt.
MECHANICAL INST ALLA TION 1 10SR NEW / EXISTING CONSTRUCTION INST ALLA TION PROCEDURES: Before you begin: Please read and understand all of these instructions thoroughly before beginning any work. Note that construction work for the installation of all T annoy products must be done to local building codes by qualified, licensed installers.
MECHANICAL INST ALLA TION 1 10SR NEW / EXISTING CONSTRUCTION INST ALLA TION PROCEDURES: 6) Leave some excess wire hanging through the opening in the pre-installation ring so the drywall contractors can cut a hole and drop the wires through.
MECHANICAL INST ALLA TION 1 10SR Fig. 4: Pre-installation ring on steel furring channel prior to drywall being placed. Fig. 5: Cutting drywall using the Rotozip™. Fig. 6: Completed install showing the reveal of the pre-installation ring relative to the ceiling board.
DIMENSIONS 1 10TB SHIPPING WEIGHT WITH ACTIVE MODULE: 40 LBS. .................................. .................................. .................................. .................................. .................................. ..............
TECHNICAL SPECIFICA TIONS ACTIVE MODULE Frequency Response: Power Rating: Maximum SPL (2) 2 1 meter: Driver Complement: LF Cutoff (-3 dB): Inputs: Outputs: Protection Limiter: Input Level: Lo Pass Fil.
Tannoy United Kingdom T: +44 (0) 1236 420199 E: enquiries@tannoy.com Tannoy North America T: 00 1 (519) 745 1158 E: inquiries@tannoyna.com Tannoy Deutschland T: 00 49 (0180) 1111 881 E: info@tannoy.com Tannoy France T: 00 33 (0) 1 7036 7473 E: ventes@tannoy.
An important point after buying a device TOA Electronics 110SR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TOA Electronics 110SR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TOA Electronics 110SR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TOA Electronics 110SR you will learn all the available features of the product, as well as information on its operation. The information that you get TOA Electronics 110SR will certainly help you make a decision on the purchase.
If you already are a holder of TOA Electronics 110SR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TOA Electronics 110SR.
However, one of the most important roles played by the user manual is to help in solving problems with TOA Electronics 110SR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TOA Electronics 110SR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
