Instruction/ maintenance manual of the product MO-425 Thermo Products
Go to page of 20
MO-425 ECN 4392- MA OIL FURNACE GENERAL SERVICE AND MAINTENANCE MANUAL FOR USE WITH THERMO PRIDE OIL FURNACES THERMO PRODUCT S, LLC . PO BOX 217 NORTH JUDSO N, IN 46366 PHONE: (574) 896-2133.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. i TABLE OF C ONTENTS SECTION BEGINNING P AGE I . GENERAL I NSTRUCTI ONS 1 I I . I N S T A L L A T I O N 2 A. CHI MNEY 2 1. PROPER CHI MNEY SI ZE 2 2. PREVENTION OF CHI MNEY CONDENSING 3 3.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 1 I. GENERAL INSTRUCTIONS - READ BEFORE START OF INSTALL ATION 1.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 2 If the " entir e" build ing is unusually tight ly construc ted a nd/or has an exha ust fan insta lled, a low pr essure z one co uld b e cre ated w ithin th e structu re.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 3 2. PREVENTION OF CHIM NEY CONDENSING: Stack gas m ay do one of tw o things as it escapes u p the chim ney : A. Rem ain en tirely in a gaseous state if the in ternal chim ney w all tem perature is above th e dew poin t, or B.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 4 3. PROPER CHIM NEY HEIGHT: The chimney shall ter minate a t lea st 3 fee t abo ve the highe st po int where it p asses thro ugh the ro of of a build ing and a t least 2 feet hig her than any portion of a bu ilding w ith in a horizontal dis tance of 10 feet.
All installations and ser vices m ust be perform ed by qualified se rvice pe rsonnel. 5 5. PRO PER CHIM NEY BOTTO M LEVEL: In cases w here the chim ney extends to the basem ent floor, the draft can us.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 6 Fig. 7: Alternate constructions that allow reduced clearances to com bustible materials.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 7 The vent conn ector pipe between the f urnace an d chim ney shall be of equal diam eter as the flue outlet of th e furnace. The vent connector pipe m ust be m ade of 24 gauge (or thicker) corrosion-resistant steel.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 8 Fig. 8: Supply air duct sizing Example The RETURN AIR DUCT SYSTEM should eq ual the w arm air duct sy stem in airflow capabilities.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 9 D. OIL TANK & PIPING: ? ? ? ? WARNING: All local codes and ordinances take precedence wi th regard to tank and oil lines.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 10 Below th e w iring diag rams for the variou s T herm o Pride oil furnace m odels.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 11 G. INITIAL BURNER OPERATION: IMPORTANT: READ B URNER INSTRUCTION MANUAL (INCLUDED WITH BURNER) BEFORE CONTINUING. To successfully service an d initially set up the oil furnace, y ou must use th e follo w ing instru men ts: A.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 12 For exam ple, if a 13% CO 2 (3.5% O 2 ) is measu red at a trace of smoke, open the air sh utter until a zero sm oke reading is obtained w ith a 12% C O 2 or 4.5% O 2 .
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 13 TURN T'STAT SE TTING ABOVE ROO M TEMPERATURE TURN THERMOSTAT TO CALL FOR HEA T DOES TH ERMOSTAT MAKE CON TA.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 14 POSITI ON THEM PER BURNER MANUFACTURERS INSTRUCTIONS REPLACE IG NITI ON TRANSFORM ER ARE THE ELECTRODES ARCING? .
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 15 PROPER COMBUST ION ACHIEVED? IS THE PROBLEM DELAYED IGNITION? IS PUMP PRESSURE SET ACCORDING TO BURNER APPLICATI.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 16 GO TO PROPER COMBUST ION ACHIEVED SECTI ON ABOVE AND SET COMBUSTION ADJUST BLOWER SPEED TO RAISE TEM PERATURE RISE. -- INCREASE L ENGTH OF BURNER ON CYCLE -- INSULATE CHIM ENY W ITH CHIMNEY LINER.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 17 B. CAD CELL CHECK OUT PROCEDURE: 1. Remove cad cell lead w ires, then start th e burner. Shortly after burner st arts, place a tem porary jum per between term inal f - f.
All installations and ser vices must be pe rformed by qualified se rvice pe rsonnel. 18 ? ? ? ? CAUTION: Do not attempt to start burn er when: 1.Ex cess oil has accumulated 2.W hen the furnace or burner is full of vapor 3.W hen the combustion chamber is very hot.
An important point after buying a device Thermo Products MO-425 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Thermo Products MO-425 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Thermo Products MO-425 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Thermo Products MO-425 you will learn all the available features of the product, as well as information on its operation. The information that you get Thermo Products MO-425 will certainly help you make a decision on the purchase.
If you already are a holder of Thermo Products MO-425, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Thermo Products MO-425.
However, one of the most important roles played by the user manual is to help in solving problems with Thermo Products MO-425. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Thermo Products MO-425 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
