Instruction/ maintenance manual of the product CM302 Thermador
Go to page of 8
INST ALLA TION INSTR UCTIONS FOR THERMADOR ® B UIL T -IN ELECTRIC O VENS Models: C272 / C302 / CM302 / CJ302 / C271 / C301 / CM301 S272 / SC272 / SCD272 / S302 / SC302 / SCD302 / S301 / SC301 / SMW27.
Page 2 The cabinet cutout dimensions for wall mounted and under the counter installations are shown in Figs. 2 and 3, respectively. It is good practice, when oven is installed at the end of a cabinet run, adjacent to a perpendicular wall or cabinet door, to allow at least 1/4" space between the side of the oven door and the wall/door.
Page 3 Fig. 2- Cabinet Cutout - Wall Mounted Installation Refer to dimensions for specific ovens on Page 4 FRONT VIEW SIDE VIEW FLOOR LINE F G Double Oven Location of Conduit Box Exposed Edge Must be a Finish-Cut D Recommended 2" Diameter Hole (4.
Page 4 Fig. 2- Cabinet Cutout - Wall Mounted Installation * Add 1/16" for stainless steel ovens (S- Series Ovens Only) ** Add 1/8" for stainless steel ovens (S- Series Ovens Only) *** Measured from cabinet face, largest door.
Page 5 Under the Counter Units — A single oven (S301, SC301, C301 or CM301) installed under the counter allows for the installation of most Thermador Gas or Electric non-Cook'n'Vent® Model Cooktops. (See Table 1 for recommended cooktop models.
Page 6 STEP 3: ELECTRICAL INST ALLA TION All model ovens on the front cover are dual rated, designed to be connected to either 120/240V AC or 120/ 208V AC, 60 Hz, 4 wire, single-phase power supply. The S301 and SC301 require a 20-amp circuit. The C271, C301, CM301 SMW272 and SM272 require a 30-amp circuit.
Page 7 208V ELECTRICAL HOOKUP Applies to C271, C272, C301, C302, CM302 and CJ302 models only. Your oven has been preset to be hooked up to 240V. 1. Turn off the oven(s). 2. Open the upper oven door. 3. Press and hold the UPPER OFF pad in a double oven or the OFF pad in a single oven.
STEP 5: INST ALLING THE BO TT OM TRIM Install the bottom vent trim and se- cure with (2) screws provided, one at each top end corner of the trim. The sheet metal bottom of the oven should be under the trim, except for the section at the center. To install the screws, open the door.
An important point after buying a device Thermador CM302 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Thermador CM302 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Thermador CM302 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Thermador CM302 you will learn all the available features of the product, as well as information on its operation. The information that you get Thermador CM302 will certainly help you make a decision on the purchase.
If you already are a holder of Thermador CM302, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Thermador CM302.
However, one of the most important roles played by the user manual is to help in solving problems with Thermador CM302. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Thermador CM302 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
