Instruction/ maintenance manual of the product TUSB3410 Texas Instruments
Go to page of 23
TUSB3410 GeneralĆPurpose Input/Output Evaluation Boar d September 2002 Universal Serial Bus Products User ’ s Guide SLLU041.
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
EVM IMPORT ANT NOTICE T exas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fit for commercial use.
EVM W ARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 4.75 V and the output voltage range of 4.75 V and 5.25 V . Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM.
Related Documentation From T exas Instruments v Preface Read This First About This Manual This user ’ s guide describes the setup and operation of the TUSB3410 general- purpose input/output evaluation board.
vi.
Contents vii Contents 1 Required Hardware and Software 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1 Hardware Items 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii.
1-1 Required Hardware and Software Required Hardware and Software The TUSB3410 general-purpose input-output EVM was designed for use with a personal computer running a USB-enabled operating system. The PC should be USB 1.1 or USB 2.0 spec compliant. This implies the BIOS, chip- sets, and operating system are all spec compliant.
Hardware Items 1-2 1.1 Hardware Items The TUSB3410 EVM is shown in Figure 1, together with typical representations of the hardware items required for its use.
Hardware Overview 1-3 Required Hardware and Software 1.2 Hardware Overview The TUSB3410 GPIO EVM hardware platform is 4,3 cm × 6,8 cm in width × length. Throughout this document, text inside of parentheses (ex.) is reference designators found on the TUSB3210 EVM.
1-4.
2-1 EVM Operation EVM Operation This chapter provides information required for proper operation of the TUSB3410 GPIO EVM. This includes power and PC connection require- ments, as well as descriptions of important operating features of the board, such as switches, jumpers, and indicators.
TUSB3410 EVM Setup 2-2 2.1 TUSB3410 EVM Setup The TUSB3410 general-purpose EVM is designed to support many USB applications. The EVM comes in a default configuration that requires no additional components on the EVM. A full description of the TUSB3410 device is specified in the data manual.
Jumpers 2-3 EVM Operation 2.6 Jumpers T able 2 – 3 is provided to help set up and configure the EVM platform jumpers for the desired mode of operation. The EVM can download firmware code from the PC through a loading program (may or may not be supplied with your EVM) or from an I 2 C EEPROM.
2-4.
3-1 Bill of Materials and EVM Layouts Bill of Materials and EVM Layouts This chapter describes the bill of materials and EVM layouts for the TUSB3410 EVM. T opic Page 3.1 Bill of Materials 3-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bill of Materials 3-2 3.1 Bill of Materials Item Qty . Reference Part Part Number PCB Footprint 1 1 CN2 Connector-DB9 747250-4 DB9-HF 2 2 C21, C1 1 µ F C2012X7R1C105M SMT_0805 3 1 C2 4.7 µ F C3216X7R1C475M SMT_1206 4 8 C3, C6, C8, C10, C49, C50, 0.1 µ F C1608X7R1H104K SMT_0603 C51, C52 5 2 C4,C5 0.
EVM Layouts 3-3 Bill of Materials and EVM Layouts 3.2 EVM Layouts Figure 3 – 1. T op Layer Figure 3 – 2. Bottom Layer.
3-4.
A-1 TUSB3410 GPIO EVM Schematic Diagram TUSB3410 GPIO EVM Schematic Diagram Appendix A.
A-2.
5 5 4 4 3 3 2 2 1 1 D D C C B B A A 06/18 /02 Voltage Divider Network ESR=0.2ohm TUSB 3410 GPIO TUSB 3410 BLOCK DIAGRAM Serial Debug SCL +3V 3 TUSB341 0 +5V Bus Pow er I2C EPRO M VDD18 SDA D- 12Mhz I2.
An important point after buying a device Texas Instruments TUSB3410 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments TUSB3410 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments TUSB3410 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments TUSB3410 you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments TUSB3410 will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments TUSB3410, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments TUSB3410.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments TUSB3410. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments TUSB3410 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
