Instruction/ maintenance manual of the product TPS60230EVM-047 Texas Instruments
Go to page of 11
July 2004 User ’ s G uide SBVU008 PMP Portable Power Products.
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
EVM IMPORT ANT NOTICE T exas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fit for commercial use.
EVM W ARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 0 V and 7 V . Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power .
Preface Read This First About This Manual This user ’s guide provides the information needed to set up and operate the TPS60230EVM-047 evaluation module. For a more detailed description of the TPS60230, please refer to the product data sheet available from the T exas I n - struments web site at http://www .
Contents iv If Y ou Need Assistance If you have questions regarding either the use of this evaluation module or the information contained in the accompanying documentation, please contact your local T.
1 TPS60230EVM-047 TPS60230EVMĆ047 This user ’s guide describes the characteristics, operation, and use of the TPS60230EVM-047 LED charge-pump current-source evaluation module (EVM).
Introduction 2 1 Introduction The T exas Instruments TPS60230EVM-047 evaluation module (EVM) helps designers evaluate the operation and performance of the TPS60230. This de- vice is an efficient charge-pump-based current sink that can drive up to five white LEDs with 25mA each.
Input/Output Connector Descriptions 3 TPS60230EVM-047 2.2 Setup Connect an input supply or battery between J1 and J2. The voltage range on this supply should stay between 2.
Printed Circuit Board (PCB) Layout 4 3 Printed Circuit Board (PCB) Layout PCB layout is critical for all switch-mode power supplies. Figure 2, Figure 3, and Figure 4 show the board layout for the TPS60230EVM-047 PWB. The nodes with high switching frequencies and currents are short and are isolated from the noise-sensitive feedback circuitry .
Schematic 5 TPS60230EVM-047 4 Schematic Figure 5. TPS60230EVM−047 Schematic 5 Bill of Materials T able 2. Bill of Materials Qty Ref Des Description Size Mfr Part Number 2 C1, C4 Capacitor , ceramic, 1.0 µ F , 6.3V , X5R, 10% 603 TDK C1608X5R0J105KT 2 C2, C3 Capacitor , ceramic, 0.
An important point after buying a device Texas Instruments TPS60230EVM-047 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments TPS60230EVM-047 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments TPS60230EVM-047 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments TPS60230EVM-047 you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments TPS60230EVM-047 will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments TPS60230EVM-047, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments TPS60230EVM-047.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments TPS60230EVM-047. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments TPS60230EVM-047 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
