Instruction/ maintenance manual of the product TPS53125EVM-599 Texas Instruments
Go to page of 17
User's Guide SLVU392 – July 2010 TPS53125EVM-599 The TPS53125EVM-599 Evaluation Module presents an easy-to-use reference design for a common dual output power supply using the TPS53125 controller in cost-sensitive applications. Also included are the schematic, board layout, and bill of materials.
Description www.ti.com List of Tables 1 TPS53125EVM-599 Electrical and Performance Specifications ...................................................... 2 2 Test Point Description .......................................................................
+ + + + + www.ti.com TPS53125EVM-599 Schematic 3 TPS53125EVM-599 Schematic For Reference Only, See Table x: for Specific Values Figure 1. TPS53125EVM-599 Schematic 3 SLVU392 – July 2010 TPS53125EVM-.
Connector and Test Point Descriptions www.ti.com 4 Connector and Test Point Descriptions 4.1 Enable Jumpers/Switches –SW1 and SW2 The TPS53125EVM-599 board includes independent enable switches for each of the two outputs.
www.ti.com Test Setup 4.2.4 Soft-Start Voltage Monitoring – TP1, TP2, and TP3 TPS53125EVM-599 provides two test points for measuring the soft-start ramp voltages. TP1 monitors the soft-start ramp of Channel 1. TP2 monitors the soft-start ramp of Channel 2.
Test Setup www.ti.com J1 to LOAD1 and J2 to LOAD2 - The connection between J1 and LOAD1 and J2 and LOAD2 of TPS53125EVM-599 can carry as much as 4 Adc each. The minimum recommended wire size is AWG #14, with the total length of wire less than 2 feet (1-foot input, 1-foot return).
LOAD1 1.05V @ 4A F AN V2 + - Oscilloscope 1M W , AC 20mV / div 20MHz LOAD2 1.8V @ 4A V3 - + - + - + A1 - + V VIN V1 + - www.ti.com Test Setup 5.2.2 Test Setup Diagram Figure 2. TPS53125EVM-599 Recommended Test Setup 5.3 Start-Up/Shutdown Procedures Perform the start-up and shutdown procedures in the following manner.
0 1 2 3 4 5 I -LoadCurrent- A LOAD 50 55 60 65 70 75 80 85 90 95 h -Efficiency-% V =8V I V =12V I V =22V I TPS53125EVM-599 Test Data www.ti.com 7. Decrease LOAD2 to 0 A. 5.4 Output Ripple Voltage Measurement Procedure Perform the Output Ripple Voltage Measurement procedure in the following manner.
0 10 20 30 40 50 60 70 80 90 100 h -Efficiency-% 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 I -LoadCurrent- A LOAD V =8V I V =12V I V =22V I V =8V I V =12V I V =22V I 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 I -LoadCurrent- A LOAD 1.
1.82 1.825 1.83 1.835 1.84 1.845 1.85 1.855 1.86 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 I -LoadCurrent- A LOAD V -OutputV oltage-V O V =8V I V =12V I V =22V I TPS53125EVM-599 Test Data www.ti.com V IN = 8 V – 22 V, V OUT1 = 1.
www.ti.com TPS53125EVM-599 Test Data V IN = 12, V OUT2 = 1.80, I OUT2 = 4 A Figure 8. TPS53125EVM-599 Output Voltage Ripple 6.4 Switch Node tV IN = 12, V OUT1 = 1.
TPS53125EVM-599 Assembly Drawings and Layout www.ti.com V IN = 12, V OUT2 = 1.80, I OUT2 = 4A Ch1: TP11 (SW2) Figure 10. TPS53125EVM-599 Switching Waveforms 7 TPS53125EVM-599 Assembly Drawings and Layout The following figures ( Figure 11 through Figure 15 ) show the design of the TPS53125EVM-599 printed-circuit board.
www.ti.com TPS53125EVM-599 Assembly Drawings and Layout Figure 12. TPS53125EVM-599 Top Copper, Viewed From Top Figure 13. TPS53125EVM-599 Bottom Copper, Viewed From Bottom 13 SLVU392 – July 2010 TPS.
TPS53125EVM-599 Assembly Drawings and Layout www.ti.com Figure 14. TPS53125EVM-599 Internal 1, X-Ray View From Top Figure 15. TPS53125EVM-599 Internal 2, X-Ray View From Top 14 TPS53125EVM-599 SLVU392.
www.ti.com TPS53125EVM-599 Bill of Materials 8 TPS53125EVM-599 Bill of Materials The Table 3 contains the bill of materials for TPS53125EVM-599. The reference designators reference the schematic in Figure 1 and assembly locations in Figure 11 . The components listed with a quantity of 0 are not populated on the PCB but are provided for reference.
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
An important point after buying a device Texas Instruments TPS53125EVM-599 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments TPS53125EVM-599 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments TPS53125EVM-599 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments TPS53125EVM-599 you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments TPS53125EVM-599 will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments TPS53125EVM-599, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments TPS53125EVM-599.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments TPS53125EVM-599. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments TPS53125EVM-599 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
