Instruction/ maintenance manual of the product TPS40003 Texas Instruments
Go to page of 17
User ’s Guide TPS40003 Based 5–A Converter in Less Than One Square Inch User ’ s G uide.
2 EVM IMPORT ANT NOTICE T exas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EV ALUA TION PURPOSES ONL Y and is not considered by TI to be fit for commercial use.
3 DYNAMIC W ARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 0 V to 5.5 V . Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM.
SLUU130A – September 2002 – Revised February 2003 4 TPS40003-Based 5-A Converter in Less Than One Square Inch TPS40003-Based 5-A Converter in Less Than One Square Inch Mark D ennis Systems Powe r Contents 1 Introduction 4 . . . . . . . . . . . . .
SLUU130A – September 2002 – Revised February 2003 5 TPS40003-Based 5-A Converter in Less Than One Square Inch 3 Schematic + Figure 1. Application Diagram for the TPS40002/3.
SLUU130A – September 2002 – Revised February 2003 6 TPS40003-Based 5-A Converter in Less Than One Square Inch 4 Design Procedure 4.1 TPS4000X Family Device Selection The TPS4000X family of devices offers four selections to encompass the frequency and output current mode choices.
SLUU130A – September 2002 – Revised February 2003 7 TPS40003-Based 5-A Converter in Less Than One Square Inch 4.4 Output Capacitor Selection Selection of the output capacitor is based on many application variables, including function, cost, size, and availability .
SLUU130A – September 2002 – Revised February 2003 8 TPS40003-Based 5-A Converter in Less Than One Square Inch 4.7 Compensation Design The TPS40003 uses voltage mode control in conjunction with a high frequency error amplifier . For the fastest transient response, the loop crossover frequency is set at 1/10 f S , or 60 kHz.
SLUU130A – September 2002 – Revised February 2003 9 TPS40003-Based 5-A Converter in Less Than One Square Inch Figure 2 shows the plots for the closed loop gain and phase with V IN = 3.3 V and I OUT = 4.4 A. At the crossover frequency of 60 kHz the phase margin is approximately 51 degrees.
SLUU130A – September 2002 – Revised February 2003 10 TPS40003-Based 5-A Converter in Less Than One Square Inch 5 PowerP AD Packaging The TPS4000X family is available in the DGQ version of TI ’ s PowerP AD thermally enhanced package.
SLUU130A – September 2002 – Revised February 2003 11 TPS40003-Based 5-A Converter in Less Than One Square Inch 6 T est Results/Performance Data The test setup is shown in figure 4 SLUP182 TP2 TP1 TP4 TP6 TP3 TP5 J1 J2 LOAD VIN VOUT GND GND (+) ( – ) DVM2 ( – ) (+) DVM1 ( – ) (+) SCOPE C + DC Power Supply CIN = 470 µ F or larger , 6.
SLUU130A – September 2002 – Revised February 2003 12 TPS40003-Based 5-A Converter in Less Than One Square Inch T ypical efficiency curves are shown in Figure 5 for an input of 3.3 V . Efficiency – % EFFICIENCY vs OUTPUT CURRENT I OUT – Output Current – A 01 2 3 45 6 50 55 60 65 70 75 80 85 90 95 100 Figure 5.
SLUU130A – September 2002 – Revised February 2003 13 TPS40003-Based 5-A Converter in Less Than One Square Inch Circuit operation with an output short circuit is shown in Figure 7. After each restart into a short circuit the pulses terminate for a period of approximately 6 ms.
SLUU130A – September 2002 – Revised February 2003 14 TPS40003-Based 5-A Converter in Less Than One Square Inch Figure 9 shows the startup waveforms with an input voltage of 3.3 V and a load of 0.3 Ω . Note that the output is held low until V SS (pin 4) goes above 0.
SLUU130A – September 2002 – Revised February 2003 15 TPS40003-Based 5-A Converter in Less Than One Square Inch 7 PCB Layout Figures 1 1 through13 show the top copper layer , the bottom copper layer , and top assembly layer , of SLUP182.
SLUU130A – September 2002 – Revised February 2003 16 TPS40003-Based 5-A Converter in Less Than One Square Inch 8 List of Material T able 1 lists the components used in this design. With minor component tweaks this design could be modified to meet a wide range of applications.
IMPORT ANT NOTICE T exas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
An important point after buying a device Texas Instruments TPS40003 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments TPS40003 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments TPS40003 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments TPS40003 you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments TPS40003 will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments TPS40003, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments TPS40003.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments TPS40003. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments TPS40003 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
