Instruction/ maintenance manual of the product TPS2330 Texas Instruments
Go to page of 22
April 2001 PMP P.
IMPORT ANT NOTICE T exas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify , before placing orders, that information being relied on is current and complete.
How to Use This Manual iii Read This First Preface How to Use This Manual This document contains the following chapters: - Chapter 1 — Introduction - Ch.
iv.
Running Title — Attribute Reference v Contents 1 Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 48-V T elecom Hot-Swap EVM 2-1 .
Running Title — Attribute Reference vi.
1-1 Introduction Fast development of telecommunications and networks has accelerated growth of products with hot-plug capability to ensure that systems are always on. Many hot-swap or hot-plug devices are already available in the worldwide market.
1-2 Introduction.
2-1 48-V T elecom Hot-Swap EVM Wi th the rapid growth of internet and telecommunications in general, more and more electronic systems are required to run continuously . Therefore, redundant systems or modules may be required to prevent the crashing of systems.
2-2 48-V T elecom Hot-Swap EVM.
3-1 Schematics of the EVM and the Interface Card The evaluation kit includes two .
3-2 Schematics of the EVM and the Interface Card Because the interface card was originally designed for universal application purposes, some of the components shown in the schematic above may not be on the board when shipped with this EVM kit. Refer to the bill of materials table for a complete component list.
3-3 Schematics of the EVM and the Interface Card Th e bills of materials (BOM) for both boards are shown in T ables 3 – 1 and 3 – 2, respectively .
3-4 Schematics of the EVM and the Interface Card C 4 and C8 on SL VP184 adjust the output turnon ramp-up rate and propagation delay time. Reducing the capacitance of C8 will increase the output ramp-up speed, and decreasing the value of C4 will reduce the output turnon delay time and increase the output ramp-up rate.
4-1 Layouts of the EVM and the Interface Card The following figures illustrate the placements of the components and the top-layer layouts for both the 48-V hot-swap EVM and the interface card respectively .
4-2 Layouts of the EVM and the Interface Card Figure 4 – 1. T op Layer of the Interface Card and Placement of the Components T op Layer T op Assembly.
4-3 Layouts of the EVM and the Interface Card Figure 4 – 2. T op Layer of the 48-V Hot-Swap EVM and Placement of Components T op Layer T op Assembly.
4-4 Layouts of the EVM and the Interface Card.
5-1 Setup of the EVM Fo r proper operation of the EVM, one 48-V power supply , and a voltage meter or an oscilloscope are required. Refer to the setup diagram in Figure 5 – 1 and follow these steps for hot plug testing: 1) V erify that the power-supply voltage is set at 48 V .
5-2 Setup of the EVM Figure 5 – 1. Evaluation Setup of the Hot-Swap Board EVM + – Power Supply 48–V , 1–A Supply Plug SL VP184 board into edge connector .
6-1 T est Points T wo test points are available on the interface card (SL VP155): TP1 – VIN1 (input voltage) TP5 – GND (ground) On the 481-V hot-swap EVM, there ar.
6-2 T est Points.
An important point after buying a device Texas Instruments TPS2330 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments TPS2330 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments TPS2330 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments TPS2330 you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments TPS2330 will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments TPS2330, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments TPS2330.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments TPS2330. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments TPS2330 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
