Instruction/ maintenance manual of the product BQ2463X EVM Texas Instruments
Go to page of 21
User's Guide SLUU396A – January 2010 – Revised July 2010 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger Contents 1 Introduction .........................................................................................
Introduction www.ti.com 1 Introduction 1.1 EVM Features • Evaluation Module For bq2461x/bq2463x • High Efficiency Synchronous Buck Charger • User-programmable up to 26V Battery Voltage • AC Adapter Operating Range 5 V–28 V • LED Indication for Control and Status Signals.
www.ti.com Introduction Table 1. I/O Description (continued) Jack Description J5–GND Ground JP1–LOW Ground JP1–TTC Timer capacitor pin JP1–HI Pull-up voltage source JP2–HI Pull-up voltage so.
Test Summary www.ti.com R25 and R28 can be changed to regulate output. V BAT = 2.1V × [1+ R25/R28]; for bq2461x; V BAT = 1.8V × [1+ R25/R28]; for bq2463x; Adjust the input voltage as required. Output set to operate at 21V (bq2461x) or 18V (bq2463x) from the factory.
bq24610/616/617/30EVM HP A422 ACPWR J1 PGND SYS J5 PGND BA T VREF JP3 PG TS APPLICA TIONCIRCUIT PH TP12 SYS VBA T TP1 ACPWR ST A T1 J 3 J2 JP1 U1 JP5 J4 V Iin I Power supply#1 Isys V Ibat V I.
Test Summary www.ti.com 2.4 Procedure 2.4.1 AC Adapter Detection Threshold 1. Make sure EQUIPMENT SETUP steps are followed. Turn on PS#2. 2. Turn on PS#1 Measure → V(J5(SYS)) = 0 ± 500mV Measure → V(TP(VREF)) = 0V ± 1000mV Measure → V(TP(REGN)) = 0V ± 500mV 3.
www.ti.com PCB Layout Guideline 2.4.4 Charger Cut-Off by Thermistor 1. Slowly increase the output voltage of PS2 until Ibat = 0 ± 10mA. Measure → V(J4(TS)) = 2.44V ± 200mV Observe → D7 (STAT1) off; D8 (STAT2) off. 2. Slowly decrease the output voltage of PS2 to 1.
Bill of Materials, Board Layout and Schematics www.ti.com 4 Bill of Materials, Board Layout and Schematics 4.1 Bill of Materials Table 4. Bill of Materials bq24610-001 bq24617-002 Bq24630-003 bq24616-.
www.ti.com Bill of Materials, Board Layout and Schematics Table 4. Bill of Materials (continued) bq24610-001 bq24617-002 Bq24630-003 bq24616-004 Value RefDes Description Size Part Number Mfr 2 2 2 2 PEC03SAAN JP1,JP3 Header, 3 pin, 100mil spacing, 0.
Bill of Materials, Board Layout and Schematics www.ti.com Table 4. Bill of Materials (continued) bq24610-001 bq24617-002 Bq24630-003 bq24616-004 Value RefDes Description Size Part Number Mfr 1 1 1 1 5001 GND Test Point, Black, Thru Hole Color 0.100 x 0.
www.ti.com Board Layout 5 Board Layout Figure 2. Top Layer 11 SLUU396A – January 2010 – Revised July 2010 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger Copyright © 2010,.
Board Layout www.ti.com Figure 3. 2 nd Layer 12 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger SLUU396A – January 2010 – Revised July 2010 Copyright © 2010, Texas Instrum.
www.ti.com Board Layout Figure 4. 3 rd Layer 13 SLUU396A – January 2010 – Revised July 2010 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger Copyright © 2010, Texas Instrum.
Board Layout www.ti.com Figure 5. Bottom Layer 14 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger SLUU396A – January 2010 – Revised July 2010 Copyright © 2010, Texas Instr.
www.ti.com Board Layout Figure 6. Top Assembly 15 SLUU396A – January 2010 – Revised July 2010 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger Copyright © 2010, Texas Instr.
Board Layout www.ti.com Figure 7. Bottom Assembly 16 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger SLUU396A – January 2010 – Revised July 2010 Copyright © 2010, Texas In.
www.ti.com Board Layout Figure 8. Top Silkscreen 17 SLUU396A – January 2010 – Revised July 2010 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger Copyright © 2010, Texas Ins.
Board Layout www.ti.com Figure 9. Bottom Silkscreen 18 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger SLUU396A – January 2010 – Revised July 2010 Copyright © 2010, Texas .
www.ti.com Schematics 6 Schematics Figure 10. bq2461x/bq2463x EVM Schematic 19 SLUU396A – January 2010 – Revised July 2010 bq2461x/bq2463x EVM (HPA422) Multi-Cell Synchronous Switch-Mode Charger C.
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
An important point after buying a device Texas Instruments BQ2463X EVM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments BQ2463X EVM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments BQ2463X EVM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments BQ2463X EVM you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments BQ2463X EVM will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments BQ2463X EVM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments BQ2463X EVM.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments BQ2463X EVM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments BQ2463X EVM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
