Instruction/ maintenance manual of the product BQ24351EVM Texas Instruments
Go to page of 13
User's Guide SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC This user's guide describes the features, setup, and operation of the bq24351EVM evaluation module. Included are the bill of materials, board layout, and schematic.
Introduction www.ti.com 1 Introduction 1.1 General Description The bq24351 evaluation module (EVM) is a complete charger module for evaluating a charger front-end protection and charger solution using the bq24351 and bq2057C devices. It is designed to deliver up to 560 mA of charge current to Li-ion or Li-polymer applications.
www.ti.com Test Summary 1.4 Controls and Key Parameters Setting Jack (1) Description Factory Setting JP1 If on, high-side sensing resistor is disabled Jumper on JP2 Reserved for other ICs Jumper (BATE.
F AUL T VBA T GA TDR V CHGIN BA T EN OUT BA T + GND HP A666 bq24351EVM JP7 V Supply 1 J1 DC+ JP1 U1 J4 BA T + V I 2 Ibat CFET AP PLICA TIO N CIRCUIT JP6 JP5 JP 4 JP3 JP 2 U2 J2 J3 I I Load 1 Test Summary www.ti.com 2.2.2 Load 1 A 10-V (or above), 2-A (or above) electronic load that can operate in constant-current mode.
www.ti.com PCB Layout Guideline 2.4 Procedure 2.4.1 Charger Current and Voltage Regulation 1. Ensure that steps in Section 2.3 are followed. 2. Enable output of PS 1. 3. Increase the output voltage of PS 1 to 5 V ± 0.1 V. 4. Enable the output of load 2.
Bill of Materials, Board Layout, and Schematic www.ti.com 4 Bill of Materials, Board Layout, and Schematic 4.1 Bill of Materials Table 1. Bill of Materials bq24351 RefDes Value Description Size Part Number MFR 1 C1 1 µ F Capacitor, ceramic, 35-V, X5R, 10% 603 Std Std 3 C2, C3, C5 1 µF Capacitor, ceramic, 10-V, X7R, 10% 603 Std Std 1 C4 0.
C001 www.ti.com Bill of Materials, Board Layout, and Schematic 4.2 Board Layout Figure 2. Top Layer 7 SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC Submit Documentatio.
C002 Bill of Materials, Board Layout, and Schematic www.ti.com Figure 3. Bottom Layer 8 bq24351EVM for Li-Ion Charger Front-End Protection IC SLUU455 – October 2010 Submit Documentation Feedback Cop.
C003 www.ti.com Bill of Materials, Board Layout, and Schematic Figure 4. Top Silk Screen 9 SLUU455 – October 2010 bq24351EVM for Li-Ion Charger Front-End Protection IC Submit Documentation Feedback .
C004 Bill of Materials, Board Layout, and Schematic www.ti.com Figure 5. Top Assembly 10 bq24351EVM for Li-Ion Charger Front-End Protection IC SLUU455 – October 2010 Submit Documentation Feedback Co.
CAUTION: Device may have surface temperature in excess of 60°C when unit is operational. www.ti.com Bill of Materials, Board Layout, and Schematic 4.3 Schematic Figure 6.
Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
An important point after buying a device Texas Instruments BQ24351EVM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Texas Instruments BQ24351EVM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Texas Instruments BQ24351EVM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Texas Instruments BQ24351EVM you will learn all the available features of the product, as well as information on its operation. The information that you get Texas Instruments BQ24351EVM will certainly help you make a decision on the purchase.
If you already are a holder of Texas Instruments BQ24351EVM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Texas Instruments BQ24351EVM.
However, one of the most important roles played by the user manual is to help in solving problems with Texas Instruments BQ24351EVM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Texas Instruments BQ24351EVM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
