Instruction/ maintenance manual of the product SS-2002RM Telex
Go to page of 18
1 9350-7741-000 Rev A, 10/2002 User Instructions Model SS-1002 Single Channel Intercom S peaker S t ation Model SS-2002 T wo Channel Intercom S peaker S t ation Model SS-2002RM T wo Channel Rack Mount.
2 FCC S t atement This equipment uses, and can radiate radio frequency energy that may cause interference to radio com- munications if not installed in accordance with this manual.
3 T able of Content s Intr oduction ............................................................................... 4 Description ................................................................................ 4 Featur es ............................
4 Introduction Thank you for purchasing the Audiocom SS-1002/SS-2002/SS-2002RM Intercom Speaker Station. W e hope the many design features of this product will satisfy your intercommunication requirements for many years to come.
5 Figure 1 - SS-1002 / SS-2002 features. Figure 2 - SS-2002RM features..
6 Inst allation Unp acking Each SS-1002 / SS-2002 / SS-2002RM is supplied with the following items. Contact the shipper or your Audiocom dealer immediately if anything is damaged or missing. Be sure to fill out and return the product registration card to T elex to properl y register your intercom station.
7 Mic Kill Receive Audiocom master stations, such as the US-2002A, can transmit an inaudible signal to turn off the microphones in all remote intercom stations on an intercom channel. This is useful when a remote intercom station has been left unattended with the microphone on.
8 Headset Connector Notes If you are using a monaural, dynamic-mic headset, or a monaural, telephone-style, dynamic-mic handset, or a handheld dynamic microphone, plug it into the Headset connector .
9 intercom stations may be reduced. Generally , if intercom stations are within a few hundred feet from the system power supply , phantom power will be suf ficient. Also note that increasing the number of stations will reduce the overall operating distance.
10 All Locally P owered Inter com Stations (Dry Lines) If intercom stations are widely distributed, you can dispense with a system power supply (PS2001L, SPS-2001, etc.) and use local power for each station. When no power is delivered on the intercom channels, this is known as dry-line operation.
11 Figure 9 - Audiocom mode connections for an SS1002 Intercom S tation in a “U” box. Note: for Clear-Com connection, use the Unbal anced Mode Intercom Channel pin-out information listed in the Specifications section.
12 Figure 10 - Audiocom mode connections for an SS2002 Intercom S tation in a “U” box. Note: for Clear-Com connection, use the Unba lanced Mode Intercom Channel pin-out information listed in the Specifications section.
13 Figure 1 1 - Audiocom cable wiring diagrams..
14 Power-Up Make sure any local power supplies are plugged in, then turn on the power switches of any phantom power supplies (PS- 2001L, SPS-2001, etc.) Sidetone Adjustment The SS-1002, SS-2002, and SS-2002RM use full-duplex audio (the same as conventional telephone lines) in which the talk and listen audio are sent and received on the same wires.
15 Operation Channel Select (SS-2002 & SS-2002RM Only) T ap the Ch Select key to select channel 1 or 2. The key is green when channel 1 is selected and red when channel two is selected. Headset/Headphone/S peaker/Microphone Selection • T o use a headset or telephone style handset, set the Speaker and Panel Mic keys to off.
16 S pecifications General Power Requir ements: Phantom Power: +24 VDC nominal, 175 mA Local Power: +12 to +15 VDC, 250 mA Dimensions: See dimension drawings.
17 Call Signaling: Pin 1 - Common Pin 2 - Local power (+12 to +15 VDC) If needed Pin 3 - Power +30 V DC Pin 4 - Intercom channel 1 audio and DC call signaling Pin 5 - Power +30 V DC Pin 6 - Intercom c.
18 TRADEMARKS Audiocom ® is a registered trademark of T elex Comm unications. Names of other products mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respectiv e companies. W ARRANTY INFORMA TION Products are warranted b y T elex Comm unications, Inc.
An important point after buying a device Telex SS-2002RM (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Telex SS-2002RM yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Telex SS-2002RM - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Telex SS-2002RM you will learn all the available features of the product, as well as information on its operation. The information that you get Telex SS-2002RM will certainly help you make a decision on the purchase.
If you already are a holder of Telex SS-2002RM, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Telex SS-2002RM.
However, one of the most important roles played by the user manual is to help in solving problems with Telex SS-2002RM. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Telex SS-2002RM along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
