Instruction/ maintenance manual of the product NI-223 Plus Telex
Go to page of 13
Model NI223 plus IP-223 iDen® Interface Technical Manual March 2008 Telex P/N LIT000150000 R e v i s i o n C.
NI223Plus - 3 - Table of Contents 1 General ................................................................................... 4 2 Front and Rear Panel Connections and Indicators ............ 4 2.1 Front Panel LED ....................................
- 4 - NI223Plus 1 General The NI223 plus is an iDen® interface product designed to connect the IP-223 Ethernet Adapter Panel to the iDen® network. The iDen® Radio Interface can be used to make Direct Connect, Group Call, Alert Calls or Emergency Group calls over the iDen® network.
NI223Plus - 5 - 3 IP-223/NI223 plus Setup 3.1 IP-223 Setup 3.1.1 Jumper Settings Jumper Position Connection Type “A” Single Ended Tx/Rx Audio Line 1: J3, J9, J11, J16, J21 Line 2: J19, J20, J25, J.
- 6 - NI223Plus listening consoles. Configuration of the ring multicast and port numbers must be unique and consistent with the IP-223 and any listening cons ole. For console configurations, please refer to the specific User Manual for tha t product. Afte r the iDen® Radio Mode has been set, the IP-22 3 must be reset.
NI223Plus - 7 - 3.2 Connecting the IP-223 and the NI223 plus Figure 3 Connections between IP-223 and NI223 plus Connect the IP-223 and the NI223 plus to the iDen® radio as show n in Figure 3. The power for the NI223 plus will be obtained from the same power conn ector the IP-223 is using.
- 8 - NI223Plus 3.4 C-Soft Setup Note This example shows a basic setup for C-Soft. Please refer to the User manual for other Vega IP based consoles if necessary . 3.4.1 Setup IP Multicast List Figure 4 Setup IP Multicast List – iD en® Radio in Phone Mode operation Figure 4 shows an example of setting two lines in Phone mode.
NI223Plus - 9 - 3.4.3 C-Soft Phone Control Buttons Figure 6 C-Soft Phone Control Buttons Setup Figure 6 shows a few of the basic C-Soft Phone Control buttons. Any button can be configured for a task by Right-Clicking on the button, then using the UI Elem ent Function pull down menu.
- 10 - NI223Plus 4.2.1 A-Key, Alert The ‘A’ key is used to send an Alert function ov er the iDen® system. Using the standard dialing keys, enter the ID of the radio. Press the “A” key to send the alert. 4.2.2 B-Key, Send The “B” key is used as a send button when placing a manually dialed phone call.
NI223Plus - 11 - 5.1.2 Receive Audio Alignment The standard Receive audio alignment procedures should be followed for the NI223 Plus installation. With AGC turned OFF, inject a 0dBm test tone into the IP-223 front end and measure the level at the Receive audio test poin t s for line 1 or 2.
- 12 - NI223Plus 6 Cable Assembly 9 17 15 11 8 20 2 18 5 4 6 10 2 1 1 3 7 12 P1 P2 P3 P4 P5 19 P6 UNDERSIDE WIRING T ABLE CABLE No. 1 CABLE No. 2 CABLE No. 3 CABLE No. 4 21 CABLE No. 5 22 16 2 9 6 9 A 13 DET AIL A SCALE 1 : 1 6 14 PIN TO PIN COLOR CABLE No.
NI223Plus - 13 - 7 W arranty , Service, Repair , and Comments Important! Be sure the exact return a ddr ess and a description of the problem or work to be done are enclosed with your equipment.
- 14 - NI223Plus 8 NI223 Plus S pecifications Operating Temperature Range: • 0 to 55 ° C for full specifications Power Requirements: • +12 to +16 VDC, semi-regulated, 1A Max. Dimensions: • 2 ¾ ” W x 4 ¾ ” D x 1 ¾ ” H Front Panel Indicators: • Green LED Power Indicato r Rear Panel Connections: • DB25 • Earth Ground.
An important point after buying a device Telex NI-223 Plus (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Telex NI-223 Plus yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Telex NI-223 Plus - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Telex NI-223 Plus you will learn all the available features of the product, as well as information on its operation. The information that you get Telex NI-223 Plus will certainly help you make a decision on the purchase.
If you already are a holder of Telex NI-223 Plus, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Telex NI-223 Plus.
However, one of the most important roles played by the user manual is to help in solving problems with Telex NI-223 Plus. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Telex NI-223 Plus along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
