Instruction/ maintenance manual of the product 760 PLUS Teledyne
Go to page of 16
INSTRUCTION MANUAL 760 PLUS VACUUM GAUGE TELEDYNE HASTINGS INSTRUMENTS ISO 9001 CER TIFIED.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 2 of 16 Manual Print History The print history shown below lists the printing da tes of all revisions and addenda created for this manual. The revision level letter in creases alphabetically as the ma nual undergoes subsequent updates.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 3 of 16 Table of Contents 1. GENERAL INFOR M AT ION......................................................................................................... ................................... 4 1.1.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 4 of 16 1. General Information This manual contains technical and general informat ion relating to the installation, operation, and calibration of the H astings 760 Plus vacuum gauge which is comprised of a pie zo vacuum transd ucer (760s) and power suppl y/display.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 5 of 16 1.2. Specifications Piezo Vacuum Transducer (760s): Accuracy ......................................................................................................± 0.25% FS* (760 Torr) Operating pressure .
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 6 of 16 2. Inst allation This section contains the necessary instructions to assist in placing the HPM-760 Plus digital vacuum gauge into operation as quickly and easily as possibl e. Please read the following thoroughl y before attempting to install or use the instrument.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 7 of 16 2.3. Power Supply/Display Installation Cut a panel opening to the following dimensions; 3. 62” (92mm) wide, 1.77” (45mm) ta ll. Insert the power supply/display through the panel cutout and secu re in place using mounting hardware supplied.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 8 of 16 3. Operating Information This section contains information on operating the PIEZO Resistive Transducer in any of its various configurations. Refer to the appropriate section fo r information on the mode in use.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 9 of 16 3.2. Piezo Transducer Input Power The 760s piezo transducer oper ates with a DC input from 15 to 30 volts. Use the 4-pin female connector supplied and makes necessary connections as outlined.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 10 of 16 3.5.2. Rear Panel Refer to page 19, 7.1.2 for r ear view and speci fic pin outs and conne ctor arrangements. AC In put Co nnector J1 Universal input power 110vac to 220 VAC. No hardware settings required.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 11 of 16 Auxili ary Relay Conta cts The THPS-760 P ower Supply has SP1 and SP2 rela ys for vari ous external switch ing/monitoring applications. Each relay has a single set of Form “C” contacts.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 12 of 16 4. Calibration 4.1. Hastings 760 Plus Piezo Transducer Zero and Span Adjustment 1. Install the transducer and power supply/displ ay then apply ope rating power. Wait a mini mum of 15 minute s before proceeding.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 13 of 16 5. Maintenance 5.1. Power Supply/Display Authorized Maintenance During normal operation and excluding the calib ration procedure, H astings 760 Plus power supply/display does not require maintenance.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 14 of 16 6. W ARRANTY 6.1. Warranty Repair Policy Hastings Instruments warrants this produc t for a period of one ye ar from the date of shipment to be free from defects in material and wo rkmanship.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 15 of 16 7. Diagrams and Drawings 7.1. Front Panel The THPS-760 has a 4 1/2-digit display that displays continuous readout.
Manual: 14 7-082010_HPM-76 0-Plus-Va cuum-Gauge Page 16 of 16 7.3. Mounting Cut out panel as shown in the diagram below. 7.4. Panel Mounting 1) Slide power supply into panel from the top. 2) Attach brackets to the side of the power supply. 3) Tighten screws against panel.
An important point after buying a device Teledyne 760 PLUS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Teledyne 760 PLUS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Teledyne 760 PLUS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Teledyne 760 PLUS you will learn all the available features of the product, as well as information on its operation. The information that you get Teledyne 760 PLUS will certainly help you make a decision on the purchase.
If you already are a holder of Teledyne 760 PLUS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Teledyne 760 PLUS.
However, one of the most important roles played by the user manual is to help in solving problems with Teledyne 760 PLUS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Teledyne 760 PLUS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center