Instruction/ maintenance manual of the product TLM TLM-1705 Tatung
Go to page of 28
OPERATING INSTRUCTIONS TLM-1705 / TLM1905.
.
i P REFACE FCC Compliance Statement This device complies with part 15 of the FCC Rules. Opeartio n is subjected to the following two conditio ns: 1. This device m ay not cause harm ful interference, and 2. This device must accept any interfe rence received, including interference that ma y cause undesired operation.
ii The Federal Comm unicati ons Comm ission warns that changes or m odificat ions of the unit not expressl y approved by the party responsi ble for com pliance could void the user’s authority to operate the equipm ent.
iii Important Operating Instructions Please read the following i nstructions carefully. Thi s manual should be retained for future use. 1. To clean the LCD monitor screen, first, make sure the monitor is in th e power off mode. Unplug t he monit or from it s power source before cleaning it.
iv Introduction CONTENTS PREFACE ..................................................................................................................... I CHAPTER 1 ........................................................................................
1 C HAPTER 1 The LCD Multimedia Monitor Unpacking After you unpack your LCD multimedia monitor, ma ke sure the follo wing items are included in the box and in good condition: Standard Item • LCD mul.
2 Identifying Components The LCD Multimedia Monitor — Front View Figure 1-1: The LCD multimedia Monitor Front View 1. Power-On Indicator This LED indicator stays lit when the power is o n and blink s when the LCD multimedia monitor is in power saving mode .
3 1. Audio Line-in 2. AC Power Jack 3. VGA (Analog) Cable With 15-Pin D-Sub VGA Connector (Male) 4. S-Video connector 5. AV connector 6. Digital VGA (DVI) Cable Connector (Optional) Adjusting the Tilting Angle The LCD multimedia m onitor’s angle settings ran ge from -3 ° to 20 ° .
4 Raising Your Monitor to an Upright Position and Adjusting Monitor Angle.
5 Power Management System The LCD multimedia m onitor complies with the VESA DPMS pow er management proposal. When th e LCD multimedia m onitor is in pow er saving mode or detects an in correct timing, the monitor screen will be blank an d the pow er LED indicator starts blin king.
6 C HAPTER 2 The Display Controls LCD Multimedia Monitor Control Panel Figure 2-1: The LCD Monitor Panel 1. OSD Menu Button Press this button t o pop up the OSD (On-Screen Display) m enu. This button is al so a Function Select but ton . 2. Adjustment Control Buttons These two buttons all ow you to adjust the selected control functions in the OSD.
7 Adjusting the Monitor’s Display OSD Main Menu To access the OSD main m enu, press the OSD Menu button. Use the Funct ion Select buttons to scro ll between the OSD main menu options.
8 H-POSITION: To move the LC D monit or’s display le ft or right on a horizontal pl ane. V-POSITION: To move the LC D monit or’s display up or down on a vertical plane. PHASE: To adjust the focus and clarity of the disp lay. CLOCK: To adjust th e display pixel alig nment.
9 EXIT: To exit the OSD-Control subm enu. GRAPHIC-CONTROL Option The Graphic-Control opt ion lets you m ake adjustm ents that effect the contrast, brightness and color of the LCD m onitor’s di splay. Press the Adjustm ent control butt on to display the submenu.
10 Press the Adjustm ent control butt on to display t he submenu. LANGUAGE: The supported languages include Germ an, English, French, Spanish, Ital ian and Japanese. AUDIO VOLUME: To increase or decrease the volume of the LCD moni tor’s sound system .
11 OSD-CONTROL Option The OSD-Control m enu option l ets you adjust t he position of the OSD on the screen. Press the Adjustm ent control butt on to display t he submenu. Use the Function Select buttons to sel ect one of the following submenu opti ons: OSD-H-POSITION: To change the position of t he OSD on a horizontal pl ane.
12 MISC-CONTROL Option The Misc-Control menu opti on lets you sel ect the OSD display language, adjust the audio volum e setting and view sy stem i nformation. Press the Adjustm ent control butt on to display t he submenu. LANGUAGE: The supported languages include Germ an, English, French, Spanish, Ital ian and Japanese.
13 EXIT: To exits the Monitor-Control submenu. OSD-CONTROL Option The OSD-Control m enu option l ets you adjust t he position of the OSD on the screen.
14 SATURATION: To adjust the color level you prefer. SHARPNESS: Press the adjustment butto n to optimize the sharpness for your specific appli cation. RESET: To reset all of the Video-C ontrol submanu set tings to the factory default. EXIT: To exit the Video-Control subm enu.
15 Note: 1. No Video When th e monitor is ON and there is no Video signal received, the following message will be displayed . 2. Signal out of monitor’s support ed range (Please refer to Addendum) W.
16 Hot-Key Buttons for Quick Adjustment of Monitor Settings. ( 〝 AUTO-ADJUST 〞 hot-key is effective only when analog input signal is selected for application) 1. " Auto-adjust " hot-key button: Press button 2 to apply the moni tor setting automatically.
17 A PPENDIX A Troubleshooting Troubleshooting Procedures This LCD monitor com es pre-adjusted w ith standard VGA tim ing. Due to output timing differences am ong various VGA car ds, you may initially experience an unstable or unclear display when a new display m ode or new VGA card is selected.
18 2. Turn off the LCD monitor and then turn it back on again. Press the OSD Menu button (refer t o Chapter 2) once and then press either Adjustment Control bu tton several times. If there is still no display, press t he other Adjustm ent Control but ton several times.
19 A PPENDIX B Technical Information LCD Monitor Specifications LCD Panel 17-inchTFT Control Functions Power Software switch w ith LED indicator (toggle ON/OFF) Main Menu Submenu ANALOG MOD E: MONITOR.
20 Display Area 337.920 mm x 270.336 mm (17.0-inch diagonal) Display Colors 16M Video Input VGA, DVI (O ptional), S-Video, AV Scanning Frequency (Analog mode) 24-80K 56-75 Scanning Frequency H/V, Hz (Digital mode)- (Optional) 31-80K 56-75 Power Management Meets VESA DPMS Power Consumption ON : 40W max.
21 A PPENDIX C Supported Timing Ite m Standards Resolution Dot Clock (MHz) Vertical Scanning Frequency (Hz) Horizontal Scanning Frequency (kHz) Sy nc Polarity or composite sy nc (H/V) Operatin g Mode 1 NEC PC98 640x400 25.20 70.15 31.50 -/- A/D 2 NEC PC98 640x400 21.
6200564280 TATUNG COMPANY OF AMERICA 2850 El Pres i d i o ST. Long Beach, CA 90810 (800) 827-2850 www.tatungusa.com.
An important point after buying a device Tatung TLM TLM-1705 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tatung TLM TLM-1705 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tatung TLM TLM-1705 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tatung TLM TLM-1705 you will learn all the available features of the product, as well as information on its operation. The information that you get Tatung TLM TLM-1705 will certainly help you make a decision on the purchase.
If you already are a holder of Tatung TLM TLM-1705, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tatung TLM TLM-1705.
However, one of the most important roles played by the user manual is to help in solving problems with Tatung TLM TLM-1705. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tatung TLM TLM-1705 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
