Instruction/ maintenance manual of the product MF-P01 Tascam
Go to page of 16
» D00637200A O WNER’S MANU AL CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE P ARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
2 PORTASTUDIO MF-P01 Important Safety Precautions IMPORT ANT (f or U .K. Customers) DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approv ed extension lead or consult your dealer .
PORTASTUDIO MF-P01 3 CA UTION: … Read all of these Instructions. … Save these Instructions f or later use. … Follow all Warnings and Instructions marked on the audio equipment. 1) Read Instructions — All the safety and operating instruc- tions should be read before the product is operated.
4 PORTASTUDIO MF-P01 The T ASCAM MF-P01 POR T ASTUDIO allo ws you to perform multitrack recordings which are not possible with an ordinary stereo cassette recorder . Multitrack recording - a brief introduction This section giv es you a brief introduction to some of the terms and techniques used in recording.
PORTASTUDIO MF-P01 5 Record-pr otecting cassettes The record-protect tab on a cassette stops you recording on that side when it is remov ed. The MF-P01 also recognizes this protection, and will not allow you to record on the side of a cassette where this tab has been remov ed.
6 PORTASTUDIO MF-P01 What y ou need to make recordings Apart from the MF-P01 itself, you will need: • Some kind of stereo master recorder (such as a cassette or MD recorder) to produce the stereo recordings. •Y ou will also need RCA (pin or phono) cables to connect the MF-P01 to other equipment.
PORTASTUDIO MF-P01 7 1 DC IN 12 V connector and POWER switch Use this jack to connect the PS-P2 A C adaptor which comes with your MF-P01. When connecting the power , make sure the po wer switch is off (slide it to the right, as you look from the back).
8 PORTASTUDIO MF-P01 5 POWER indicator This indicator is lit when the MF-P01 is connected to the power supply and switched on. 6 T ape counter and r eset button The tape counter allows you to note dif ferent parts of the tape and locate to them. Pressing the RESET button resets the counter to "000".
PORTASTUDIO MF-P01 9 To change the "record-ready" track, press down the REC FUNCTION switch for the desired track. The cur- rent "record-ready" track will be automatically released.
10 PORTASTUDIO MF-P01 This section describes ho w to make a 4-track recording using the MF-P01. For this, we will assume that you are making a recording of your guitar on track 1 using a microphone first, and then recording your voice on track 2 while monitoring track 1 Setting up 1) Make sur e the MF-P01 is turned off .
PORTASTUDIO MF-P01 11 Recording the fir st track 1) Press the REC FUNCTION k ey f or track 1 so that the REC indicator flashes. Y ou are now ready to record on track 1. 2) Press do wn the RECORD button to start r ecording the first guitar track. The REC indicator for track 1 lights steadily .
12 PORTASTUDIO MF-P01 4) Adjust the recording le vel for track 2, in the same way as shown abo ve (see "Setting the level"). Use the LEVEL and P AN controls for track 1 to control the track 1 sound. Use the MASTER control to adjust the ov erall monitor le vel.
PORTASTUDIO MF-P01 13 Mixdown 1) Make sur e that no REC indicator is lit. To release the "record-ready" track (to make all tracks "record-off"), press a REC FUNCTION switch whose REC indicator is not lit lightly . 2) Set the INPUT LEVEL fader to minimum.
14 PORTASTUDIO MF-P01 MF-P01, and may damage the amplifier . Only use outputs which are marked LINE OUT , PRE OUT , DIRECT OUT and so on. A void using any outputs marked SPEAKER OUT , SP OUT , 4 Ω , 8 Ω , 16 Ω or the like. Recording with eff ects Professional recordings often use effects lik e digital rev erberation on vocals, etc.
PORTASTUDIO MF-P01 15 T racing faults in a recording setup is often a mixture of logical deduction and patience. V ery often, the problem is caused by something simple; a cable which hasn’t been plugged in properly , or a faulty cable.
Headphone output (1/4" stereo phone jack) Output level: 4 mW + 4 mW Output impedance: 30 Ω Frequency response: 50 Hz to 12.5 kHz +/-3 dB Signal-to-noise ratio: 43 dB T otal Harmonic Distor tion: Better than 3.0% Channel separation: Better than 40 dB Erasure: 65 dB (at 1 kHz) • 0 dBV is referenced to 1 volt.
An important point after buying a device Tascam MF-P01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Tascam MF-P01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Tascam MF-P01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Tascam MF-P01 you will learn all the available features of the product, as well as information on its operation. The information that you get Tascam MF-P01 will certainly help you make a decision on the purchase.
If you already are a holder of Tascam MF-P01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Tascam MF-P01.
However, one of the most important roles played by the user manual is to help in solving problems with Tascam MF-P01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Tascam MF-P01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
