Instruction/ maintenance manual of the product MSE 8321 TANDBERG
Go to page of 18
Codian ISDN Gateway MSE 8321 Getting started.
Codian ISDN GW MSE 8321 Getting started.
Copy right © Codian 2008. All rights reser ved. This Getting Star ted Guide ma y not be copied, photocopied, translated, r eproduc ed, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of Codian Limited.
T able of conten ts General inf ormation .......... .......... .......... ........... .......... .......... ............. .......... ........... .......... .. .... . 1 About the ISDN g ateway .......... ........... ............ .......... ........... .
General information 1 General informa tion About the ISD N gatewa y The ISDN gatew a y is a high perfor mance video gatew ay which enables ISDN netw ork connectivity for the Codian IP-based video infrastructure products as w ell as IP-based endpoints .
2 LED behavior T able 1 descr ibes the behavior of the LEDs . T able 1: ISDN gateway LED behavior LED Co lor Indicates Compact Flash Activity Flashing gr een One of: the ISDN gatewa y is booting .
General information 3 Ethernet P or t Status , for each Ether net por t: FDX Green The link has been negotiated as a full-du plex link Act Gr een Pa ckets are being transmitted on this por t Link Gree.
4 Installing the ISDN gatewa y F or infor mation about po w ering the MSE 8 000, refer to the Getting Star ted Guide that accompanied the chassis. Install the ISDN gat ewa y into the MSE 8000 chassis 1 Remov e the blade or blanking blade from the slot into which you are going to install the ISDN gatewa y: i Using a No .
Installing the ISDN gateway 5 5 Using a No .1 Phillips screwdriver , tighten the screws in the retaining latches with a clockwise quar ter tur n. Figur e 2: Inser ting a blade into the chassis Figur e.
6 Connecting the ISDN gatew ay Y our ISDN connection Outside North America Check with your netw ork pro vider to ensure that your incoming ISDN PRI line is ter minated in an NTU/CSU (Netw ork T er m ination Unit/ Channel Ser vice Unit). If it is not, then seek their advice regarding the pro visioning of suc h a device .
Initial configuration 7 Initial configur ation Step one: Configur e Ethernet Port A settings The default setting for the ISDN gate wa y Ether net por ts is auto-sensing mode .
8 Configuring the ISDN ga teway Step one: Log in to the ISDN gate wa y All administration of the ISDN gate wa y is perfor med via the web interf ace . 1 T o log in to the Log in to the Super visor’ s w eb interface. 2G o t o Hardware > Blades and clic k the IP address of the ISDN gatew a y.
Configuring the ISDN gateway 9 Step three: C onfigure an H.323 gatek e eper If you ha ve H.32 3 endpoints, using an H.323 ga tekeeper can ma ke it easier for ca llers to make their call. Y ou can configure the ISDN gate wa y to use an exter nal gatekeeper or its o wn built-in gatek eeper .
10 ISDN to IP dial plan setup Options 1 and 2 will automaticall y handle both voice and video calls . Option 1 - This example assumes that y ou ha v e a PRI line that has 100 numbers (00 to 99) associated with it and tha t all your endpoints are r e gistered to a gatekeeper with registrations in the range 5900 - 5999.
Troubleshooting and tec hnical support information 11 T r oubleshooting and technical suppor t information Refer to this section if you ar e exper ienci ng difficulties with the ISDN gate wa y. Ensure that y ou ha ve follo w ed the instr uctions in this guide when installing and configuring the ISDN gatew ay.
12 Getting more help If the documentation does not an sw er your questio n or you ha v e a prob lem with one of our products: 1 Refer to the T echnical FA Q and T roubleshooter sections of the w eb site. W e keep both sections up to da te with the latest infor mation fr om our tec hnical suppor t team regarding the r esolution of customer issues .
Pin outs 13 Pin outs The pin numbering for the PRI por ts on the ISDN gatewa y is shown in Figur e 4. The pin assignments for the PRI por ts are sho wn in T able 2: Figur e 4: Pin numbering for PRI po.
61-0020-02.
An important point after buying a device TANDBERG MSE 8321 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TANDBERG MSE 8321 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TANDBERG MSE 8321 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TANDBERG MSE 8321 you will learn all the available features of the product, as well as information on its operation. The information that you get TANDBERG MSE 8321 will certainly help you make a decision on the purchase.
If you already are a holder of TANDBERG MSE 8321, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TANDBERG MSE 8321.
However, one of the most important roles played by the user manual is to help in solving problems with TANDBERG MSE 8321. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TANDBERG MSE 8321 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
