Instruction/ maintenance manual of the product 4500 Series TANDBERG
Go to page of 19
Codian HD MCU MCU 4500 Series Getting started.
Codian MCU MCU 4500 Series Getting started.
Copy right © Codian 2008. All rights reser ved. This Getting Star ted Guide ma y not be copied, photocopied, translated, r eproduc ed, or con verted into any electronic or machine-readable form in whole or in par t without prior wr itten appro v al of Codian Limited.
T able of conten ts General inf ormation .......... .......... .......... ........... .......... .......... ............. .......... ........... .......... .. .... . 1 About the M ultipoint Cont rol Unit (M CU) ................... .......... .........
General information 1 General informa tion About the Multipoint Control Unit (MCU) The MCU 4500 Series is a range of tec hnolog ically ad vanced and po w erful Multipoint Contr ol Units. The y are designed to combine con tinuous presence a t high definition and the highest possible v oice quality .
2 LED beha vior T able 1 descr ibes the behavior of the LEDs . T able 1: MCU LED behavior LED Co lor Indicates Compact Flash Activity Flashing gr een One of: the MCU is booting a configuration.
LED behavior 3 Ethernet P or t Status, for each Ether net por t : FDX Green The link has been negotiated as a full- duplex link Act Green Pa c kets ar e being transmitted on this por t Link Green The .
4 Co nnecting the MCU Before you star t Step one: Connect power Connect the po w er connector on the rear of the unit to the pow er supply using the supplied po wer ca ble .
Initial configuration 5 Initial configur ation Step one: Connect to the console port 1 Ensure po wer is connected to the MCU and the Status LED is green. 2 Connect the console por t of the MCU to the serial por t of your PC using the blue RJ45 to DB9 cab le supplied.
6 T o configure Ether net P or t A, enter the follo wing for auto-sensing mode: ethertype auto or to configure a speed and duplex, use the follo wing command: ethertype <10|100> <half|ful.
Configuring the MCU 7 Co nfiguring the MCU Step one: Log in to the MCU All administration of the MCU is perfor med v ia the w eb interface. T o log in to the w eb interface of the MCU: 1 Use your bro wser to na vigate to the IP addr ess of the MCU (to disco ver the IP address, r efer to the pre vious section).
8 Step three: A dd endpoints (optional) One wa y to add par t icipants to a conference tha t you cr eate is to ha ve the MCU automaticall y call them when the conference star ts. T o do this, you configure their endpoints on the MCU. When you set up a conference , you can choose the endpoints from the P re- conf igured pa rticipants list.
Using the MCU 9 Usi n g t he M CU Creating conferences T o crea te a conference: 1 In the w eb interface of the MCU, go to Con fe re nc es and clic k Add new confer ence . 2T y p e a Name for the conference, for example SalesMeeting . 3 T ype an optional numeric identifier , for example 123 .
10 Calling partic ipants in to a conferenc e T o call par ticipants in to a conference: 1 In the w eb interface of the MCU, go to Conf er en ce s and clic k on the name of an active confer ence. 2O n t h e Pa r t ic i pa nt s tab , clic k Add partici pant to call out to an H.
Using the MCU 11 Streaming conferences Streaming is a wa y of viewing a conference in a standard w eb bro wser . The MCU allo ws streaming of video and, if enab led for a conference , the streaming of data. Y ou can also conduct a text ‘chat’ and add notes and dra wings to the data str eam.
12 Instruc ting confer ence par ticipants Y ou need to tell conference par ticipants ho w to join conferences . Y ou can also tell them ho w to use the Far-End Camera Contr o ls (FECC) to na vigate menus in the auto attendant and choose conference la youts.
Troubleshooting and tec hnical support information 13 T r oubleshooting and technical suppor t information Using the ev ent log to help solve a problem Unless you are ex periencing a prob lem, all e v ent logging sources should be set to the default, which is Errors, warnings and information .
14 T echnical specifications P ow er requiremen ts Over- current protection Ensure the suppl y to this unit is protected b y a branch circuit protector rated b y a maximum of 20A.
61-0011-05.
An important point after buying a device TANDBERG 4500 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TANDBERG 4500 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TANDBERG 4500 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TANDBERG 4500 Series you will learn all the available features of the product, as well as information on its operation. The information that you get TANDBERG 4500 Series will certainly help you make a decision on the purchase.
If you already are a holder of TANDBERG 4500 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TANDBERG 4500 Series.
However, one of the most important roles played by the user manual is to help in solving problems with TANDBERG 4500 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TANDBERG 4500 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
