Instruction/ maintenance manual of the product 100 TAG
Go to page of 131
OPERATOR’ S MANUAL MIL-BOOK 100 SERIES NOTEBOOK 22355 TAG Way, Dulles, VA 20166 Tel: (703) 406.3000 Fax: (703) 607.3853.
TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice.
Regulations Information Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
Please note: The use of a non-shielded interface cable with this equipment is prohibited. Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This dig.
About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.
CAUTION : Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT : Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
FRENCH ATTENTION : II y a danger d ’ explosion s ’ il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d ’ un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant.
Caution (for USA Users) To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord. Power Supply Cord: (optional) Detachable, minimum 1.
i Table of Contents Preface .................................................................................. v Chapter 1 Getting Started ..................................................... 1-1 Getting the Computer Running .........................
ii Front Components ............................................................... 1-16 Bottom-Side Compontents .................................................. 1-17 Top Compontents ................................................................ 1-18 Chapter 2 Operating Your Computer .
iii Configuring the Display Modes ..................................... 2-17 Using the Audio Features .................................................... 2-20 Connecting Audio Devices ............................................. 2-20 Using the Communication Features .
iv Chapter 5 SCU (Setup Configuration Utility) ....................... 5-1 When and How to Use the SCU Program .............................. 5-2 When to Use .................................................................... 5-2 Starting SCU .......
v Battery Problems ............................................................. 8-4 CD/COMBO Drive Problems (on optional docking station) 8-5 Display Problems ............................................................. 8-5 Floppy Disk Drive Problems (on optional docking station) 8-7 Hardware Device Problems .
vi Chapter 3, Managing Power , provides information on power. Chapter 4, Expanding Your Computer , provides information on installing and using peripheral devices. Chapter 5, SCU (Setup Configuration Utility ) , describes the SCU program that configures the computer ’ s BIOS settings.
vii Notational Conventions Throughout this manual, the following conventions are used to distinguish elements of text. NOTE: identifies additional information that requires special attention. CAUTION: identifies important information which, if not followed, may result in loss of data or damage to the computer.
Getting Started 1- 1 CHAPTER 1 Getting Started Congratulations on purchasing this industrial notebook computer. It ’ s rugged, compact, and portable design allows you to use it in the field or inside a vehicle and other demanding situations where conventional notebook computers just cannot measure up.
Getting Started 1- 2 Getting the Computer Running This section guides you through the procedures for getting the computer ready for operation. Unpacking After unpacking the shipping carton, you should.
Getting Started 1- 3 1. Make sure the computer is turned off. 2. Plug the DC cord of the AC adapter to the power connector on the computer. NOTE: When the computer is attached to the docking station, connect the DC cord to the power connector on the docking station instead.
Getting Started 1-4 Closing the Cover When closing the cover , make sure that the hook is latched properly to safeguard against the f ollowing: T o prevent damage to the LCD screen during transport. T o prevent the computer from accidenta lly wa king up from Suspend mode during transport without the us er’s knowledge.
Getting Started 1-5 Turning Off T o turn off the com puter power, use the “Shut Down” comm and of your operating system. NOTE: There are other ways you can stop the computer so that you will be back to where you left off when you next turn on the computer.
Getting Started 1- 6 Ref Component Description See Also Battery Charge Indicator: – glows green when the battery is fully charged. – Glows orange when the battery is being charged. – Is dark when battery has no charge left and AC adapter is connected and powered on.
Getting Started 1- 7 Left-Side Components Ref Component Description See Also ΠAudio Output Connector Connects a hi-fi set, radio set, synthesizer, walkman, etc.
Getting Started 1- 8 Rear Components Ref Component Description See Also Œ USB Port Each of the two ports connects a USB device, such as a USB floppy drive, printer, digital camera, joystick, and more. • VGA Port Connects an external monitor. Ž Serial Port Connects a serial device, such as mouse.
Getting Started 1-9 Front Components Ref Component Description See Also Not ched H o le Allows you to hook the computer to the docking s tation. Wireles s Mod em or GSM Ant e nna Serves as the antenna fo r the option al wireless m odem or GSM. T o uchscreen Pen Pr o vides a c onvenie nt way to use the touchscreen.
Getting Started 1- 10 Ref Component Description See Also Œ Speaker Sends out sound and voice from the computer. • Battery Compartment Cover Open the cover to access the battery pack. Ž Battery Cover Latch Locks the battery compartment. • Docking Connector Serves as the interface between the docking station and the computer.
Getting Started 1-11 Top-Open Components Ref Component Description See Also LCD Screen Displays the output of the c omputer. Device Indic a tors Shows the curre nt status of the computer’s devices. Caps Lock I ndicator – glows green when Caps Lock key is pres sed and its function is activated.
Getting Started 1- 12 LAN 10/100 Indicator – glows orange when LAN speed is 10 MBPS – glows green when LAN speed is 100 MBPS Hard Disk Drive Indicator (includes Floppy Disk Drive or CD-ROM Drive In-use Indicator when computer is connected to docking station) Ž Keyboard Serves as the data input device of the computer.
Getting Started 1- 13 Attaching and Detaching the Computer To/From the Docking Station WARNING: Make sure that the computer is off before connecting it to or disconnecting it from the docking station to prevent damage to either computer or docking station.
Getting Started 1- 14 Taking a Look at the Docking Station (option) This section identifies the external components of the docking station and briefly describes the function of each component. Right-Side Components Ref Component Description See Also Œ Device Indicators Shows the current status of the docking station and computer ’ s devices.
Getting Started 1-15 Left-Side Components Ref Component Description See Also n USB Ports Each of the two ports connects an USB device such as printer, digital camera, joystick and mor e. o Release Tab Press the Release Tab on both sides and lift up to release com puter from docking stat ion.
Getting Started 1- 16 Ref Component Description See Also Œ Serial Ports Connect serial devices such as mouse, etc. • Parallel Port Connects a parallel device such as printer. Ž VGA Port Connects an external monitor. • USB Port Connects a USB device, such as printer, digital camera, joystick and more.
Getting Started 1- 17 Bottom-Side Components Ref Component Description See Also ΠSpeaker Sends out sound and voice from the docking station..
Getting Started 1- 18 Top Components Ref Component Description See Also Œ Hooks Secures the computer to the docking station. • Docking Connector Serves as the interface between the docking station and the computer.
Getting Started 1- 19 Where to Go from Here As your computer is ready for operation, you may want to do any of the following now: For this purpose … Do this … To know more about the computer … Go on to the next chapter. To install the operating system if your dealer has not already done so … See the operating system manual.
Getting Started 1- 20.
CHAPTER 2 Operating Your Computer This chapter provides information about the use of the computer. If you are new to computers, reading this chapter will help you learn the operating basics. If you are already a computer user but are new to notebook computers, you may choose to read only the parts containing information unique to your computer.
Operating Your Computer 2- 2 Starting and Stopping the Computer There are a number of ways to start and stop the computer. Starting the Computer You always start the computer using the power button .
Operating Your Computer 2- 3 To stop in this mode … Do this … To start up or resume again Suspend Depending on your settings in Windows, you can place the computer in Suspend mode by pressing the power button or by closing the display cover. Press the power button.
Operating Your Computer 2- 4 Using the Keyboard Your keyboard has all the standard functions of a full-sized computer keyboard plus a Fn. key added for specific functions.
Operating Your Computer 2-5 Numeric Keypad A 15-key numeric keypad is embedded in the typewriter keys as shown next: Numeric keys facilitate enteri ng of numbers and calculations. When Num Lk is on, the numeric keys are activated; meaning you can use these keys to enter numerals with “Fn” key.
Operating Your Computer 2-6 Function Keys On the top row of the keys are the function keys: F1 to F12 . Function keys are multi-purpose key s that perform functions defined by individual programs. Hot key functions are assigned to F1, F3 , F4 , F5 , F6 , F8 , F9 , an d F10 by your computer .
Operating Your Computer 2- 7 Key Description Fn + F9 Switches the display output to one of the following three when an external CRT monitor is connected through the docking station.
Operating Your Computer 2- 8 Using the Touchpad CAUTION: Do not use a sharp object such as a pen on the touchpad. Doing so may damage the touchpad surface. NOTE: For optimal performance of the touchpad, keep your fingers and the pads clean and dry. When tapping on the pad, tap lightly.
Operating Your Computer 2- 9 Term Action Drag and drop Press and hold the left button, then move your fingers until you reach your destination (drag). Finally, release the button (drop) when you finish dragging your selection to the destination. The object will drop into the new location.
Operating Your Computer 2- 10 Using the Touchscreen (Optional) CAUTION: Do not use a sharp object such as a ballpoint pen or pencil on the touchscreen. Doing so may damage the touchscreen surface. Use the included touchscreen pen instead, which can be stretched for better grip and handling.
Operating Your Computer 2- 11 Term Action Scroll To scroll is to move up and down or left and right in the working area on the screen. To move vertically, place your finger or pen on the right edge of the touchscreen and slide your finger or pen up and down along the edge.
Operating Your Computer 2- 12 Using the Floppy Disk Drive (optional) Your computer may come with the optional floppy disk drive as drive A through the optional docking station .
Operating Your Computer 2- 13 Inserting and Ejecting Floppy Disks To insert a floppy disk, hold it with the arrow facing up and towards the drive. Slide the disk into the drive until it clicks into place. To eject a floppy disk, first ensure that the floppy disk drive in-use indicator is off, and then press the eject button on the drive.
Operating Your Computer 2- 14 Using the Hard Disk Drive Your computer comes with a hard disk drive as drive C . A hard disk drive is a storage device with non-removable, rotating, magnetic storage platters inside it. It is where your operating system and application software programs are stored.
Operating Your Computer 2- 15 Using the CD/COMBO Drive (optional) Your computer may come with an optional CD-ROM drive, COMBO drives, or through the optional docking station. This drive is usually configured as drive D . The drive uses removable 5.25-inch silver CD-ROM discs, which look like standard music CDs.
Operating Your Computer 2- 16 Inserting and removing a CD Follow this procedure to insert or remove a CD. 1. Turn on the computer. 2. Press the eject button and the CD tray will slide out partially. Gently pull it until fully extended. 3. To insert a CD, put down the CD in the tray with its label facing up.
Operating Your Computer 2- 17 Using the Video Features The video subsystem of your computer features: l 12.1-inch TFT (Thin-Film Transistor) color LCD display with 1024x768 XGA (Extended Video Graphics Array) resolution. l Sunlight Readable Panel , Transflective LCD (Optional).
Operating Your Computer 2- 18 Display Mode LCD Only CRT Only Simultaneous Display Resolution Colors 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 640x480 32-bit √ √ √ 8-bit √ √ √.
Operating Your Computer 2- 19 Display Mode LCD Only CRT Only Simultaneous Display 8-bit √ √ √ 16-bit √ √ √ 24-bit √ √ √ 1024x768 32-bit √ √ √ 8-bit √ 16-bit √ 24-bit √ 11.
Operating Your Computer 2- 20 Using the Audio Features NOTE: l To take advantage of the enhanced audio capabilities, t he audio driver supplied with your computer must be installed . l If you experience interference while recording, try lowering the microphone recording volume.
Operating Your Computer 2- 21 Using the Communication Features Using the Modem NOTE: To take advantage of the modem feature, the modem driver supplied with your computer must be installed.
Operating Your Computer 2- 22.
Managing Power 3- 1 CHAPTER 3 Managing Power Y our computer operates either on external AC power, car adapter, or internal battery power. This chapter tells you how you can effectively manage power. To maintain optimal battery performance, it is important that you use the battery in the proper way.
Managing Power 3- 2 AC and Car Adapter CAUTION: l The AC and car adapter is designed for use with your computer only. Connecting the AC adapter to another device can damage the adapter. l The AC power cord supplied with your computer is for use in the country where you purchased your computer.
Managing Power 3- 3 Battery Pack The battery pack is the internal power source for the computer. It is rechargeable using the AC or car adapter. The operating time of a fully charged battery pack depends on how you are using the computer. When your applications often access peripherals, you will experience a shorter operating time.
Managing Power 3- 4 Initializing the Battery Pack Y ou need to initialize a new battery pack before using it for the first time or when the actual operating time of a battery pack is much less than expected. Initializing is the process of fully charging, discharging, and then charging.
Managing Power 3- 5 If you often rely on battery power for a long period of time while traveling, you may consider the purchase of an additional battery pack from your dealer and keep it with you in a fully charged state as a backup. To replace the battery pack, follow these steps: 1.
Managing Power 3- 6 l CAUTION: l If you are using a flash PC Card, do not access the card during battery low periods. This is because the access may take longer than the time it takes the battery to run out of charge, thus making your access to the card unsuccessful.
Managing Power 3- 7 Power Management Y our computer supports APM (Advanced Power Management) and ACPI (Advanced Configuration and Power Interface) for power management. The power management feature allows you to reduce the power consumption for energy saving.
Managing Power 3- 8 Manual Power Management Y ou can manually initiate Suspend-to-disk mode at any time in one of two ways: l Use the O/S that supports the Suspend function. l Press down the power button and release it in less than 4 seconds with the system on.
Managing Power 3- 9 Power-Saving Tips In addition to your computer ’ s automatic power management, you can do your part to maximize the battery ’ s operating time by following these suggestions. l Do not disable Power Management. l Decrease the LCD brightness to the lowest comfortable level.
Managing Power 3- 10.
Expanding Your Computer 4- 1 CHAPTER 4 Expanding Your Computer You can expand the capabilities of your computer by connecting other peripheral devices. When using a device, be sure to read the instructions accompanying the device together with the relevant section in this chapter.
Expanding Your Computer 4- 2 Connecting an External Monitor If you want the benefits of a larger display screen with higher resolution, you can connect an external CRT monitor to your computer through the optional docking station. Follow this procedure to connect an external monitor: 1.
Expanding Your Computer 4- 3 Connecting a Parallel Device (optional) The optional docking station has a p arallel port for connecting a parallel device such as printer. The port supports ECP (Extended Capabilities Port) and EPP (Enhanced Parallel Port) modes that turn the standard parallel port into a high-speed bi-directional peripheral port.
Expanding Your Computer 4- 4 Connecting a Serial Device Y our computer has a serial port for connecting a serial device such as a serial mouse or modem. Follow this procedure to connect a serial device: 1. Make sure the “ COM1 Port ” item is set properly in the SCU program.
Expanding Your Computer 4- 5 Connecting a USB Device (USB 2.0) Y our computer has one USB port on the right side for connecting USB 2.0 devices such as digital camera, scanner, printer, modem, or mouse and two USB ports on the left side of the optional docking station.
Expanding Your Computer 4- 6 Using PC Cards Y our computer has one PC Card slot to accommodate one type II card. ZV Port and CardBus Support Y our computer ’ s PC Card slot supports CardBus and ZV (Zoomed-Video) Port specifications. CardBus is the 32-bit version of PC Card technology.
Expanding Your Computer 4- 7 To remove a PC Card : 1. Your operating system may require you to stop the PC Card before you actually remove it. (In Windows, double-click the PC Card icon in Control Panel to stop the card.) 2. Push the eject button and the card will slide out slightly.
Expanding Your Computer 4- 8 System Memory Upgrade Y ou can upgrade your computer by changing system memory to a maximum of 1GB on the DDR SDRAM slot. However, to avoid damage during the installation procedure, please ask your dealer for help.
Setup Configuration Utility 5- 1 CHAPTER 5 Setup Configuration Utility (SCU) SCU is a program for configuring the BIOS (Basic input/output System) settings of the computer. BIOS are a layer of software, called firmware that translates instructions from other layers of software into instructions that the computer hardware can understand.
Setup Configuration Utility 5- 2 When and How to Use the SCU Program When to Use Y ou need to run the SCU program when: l You see an error message on the screen requesting you to run Setup. l You want to restore the factory default settings. l You want to modify some specific settings according to the hardware.
Setup Configuration Utility 5- 3 The menu can be divided into four areas: l On the top line is the menu bar containing the titles of the available menus. Each menu title brings a specific menu. l The center left column of the menu contains items that you can set for the selected menu title.
Setup Configuration Utility 5- 4 Moving Around and Making Selections A brief description of keyboard usage is listed next: Key Function ← , → Selects a menu title. ↑ , ↓ Selects an item or option. Enter Opens or closes the options window when an item is selected.
Setup Configuration Utility 5- 5 Main Menu The Main menu contains the basic configuration settings of the system. Date and Time Sets the system date and time.
Setup Configuration Utility 5- 6 Internal and Numlock sets if you can enter a number when Num Lock is turn off. When this item is enabled, you can press and hold FN , and then press a letter key to enter a number even if Num Lock is turned off. When this is disabled, you cannot enter a number with the above method.
Setup Configuration Utility 5- 7 Geyserville Support Enables or disables the Geyserville feature of the CPU. The Geyserville feature helps conserve battery life by decreasing the CPU ’ s running speed under certain conditions while still maintaining a high performance.
Setup Configuration Utility 5- 8 Shared Video Memory sets the shared memory size of the video controller. The options are 4M, 8M, 16M and 32M. Com Ports.
Setup Configuration Utility 5- 9 Security Menu The Security menu contains the security setting that safeguards your system against unauthorized use. Set Password allows you to set the password for your system. When typing password, first make usre that Num Lock is off, then type your password in the entry fields and press Enter .
Setup Configuration Utility 5- 10 Boot Menu The Boot men sets the sequence of the devices to be searched for the operating system. Boot Sequence sets the first, second, third, and fourth booting devices. The system will try to boot from the first device but if it is not available, will try the next boot device.
Setup Configuration Utility 5- 11 Exit Menu The Exit menu displays ways of exiting SCU. After finished with your setting, you must save and exit so that the new setting can take effect. Save Change and Exit saves the changes you have made and exits SCU.
Setup Configuration Utility 5- 12.
Installing Software Drivers 6- 1 CHAPTER 6 Installing Software Drivers To take full advantage of the unique features of your computer, some operating systems require custom software, known as drivers, to be installed. If you purchased the computer with Windows pre-installed; your dealer may have already installed the drivers.
Installing Software Drivers 6- 2 How to Use the CD NOTES: • The drivers may have been updated after this manual was publishe d. For driver ’ s upgrade, please contact your dealer. • You can always find README or document files on the CD. These files contain the latest information from the software supplier.
Install Device Driver for Windows 2000/Windows XP T o install the necessary driver , just click on the particular option and follow the onscreen instructions to continue and com plete installation. Device Driver Press the “Device driver” button, the system will auto install include VGA, Audio, Modem, LAN , W ireless LAN, USB 2.
Installing Software Drivers 6- 4 VGA Allows you to select high-resolution displays with richer colors. It can drive CD displays as well as CRT displays. Audio Allows you to take full advantage of the audio subsystem. Modem The modem driver allows you to transmit information over a standard telephone line through RJ-11 port.
Installing Software Drivers 6- 5 Install Touch Screen Driver for Windows 2000 1. Insert the driver CD into the drive. 2. Click on “ TOUCH SCREEN ” then “ WIN2000 ” , and follow the onscreen instructions to continue. 3. When finished installing, select “ Yes ” to reboot your system.
Installing Software Drivers 6- 6 Installing Drivers for Windows XP To set up the necessary drivers for Windows XP, click on “ TOUCH SCREEN ” on the initial screen.
Installing Software Drivers 6-7 Install Touch Screen Driver for Windows XP Hardware Install: (1) Insert the driver CD to the CD drive, to bring up the following screen.
Installing Software Drivers 6- 8 (2) When the TSRC-XP.htm file appear, then select ” START ” -> “ Control Panel ” button..
Installing Software Drivers 6-9 (3) When the “Control Panel “ sc reen appear , then click on “ performance and Maintenance” bu tton..
Installing Software Drivers 6-10 (5) When the “Performance and Maintenance” screen appear , and then click on “System” button..
Installing Software Drivers 6- 11 (5) When the “ System Properties ” screen appear, and then click on “ Hardware ” and “ Device Manager “ button.
Installing Software Drivers 6-12 (6) When the “Device Manager” screen appear , then click on “ ?Unknown device” and then cl ick on the “Properties” icon.
Installing Software Drivers 6- 13 (7) When the “ Unknown Device Properties ” screen appear, and then click on “ Reinstall Driver ” button..
Installing Software Drivers 6-14 (8) When the “Hardware Update W izard” appears, click on “ Install the software automatically [Recomm and], then click on ”Next”. (9) When the “Hardware Installati on” screen appears, click on ”Continue Anyway”.
Installing Software Drivers 6- 15 (10) When the “ Hardware Update Wizard ” screen appears, click on ” Finish ” button..
Installing Software Drivers 6- 16 (11) When the “ PenMount DMC9000 and DMC9100 Properties ” screen appears, click on ” Close ” button to exit the driver installation.
Installing Software Drivers 6- 17 Touchscreen Utility To install the touchscreen utility, perform the following: (1) Insert the driver CD to the CD drive, to bring up the following screen.
Installing Software Drivers 6- 18 (3) Enter the following directory on the driver CD: TOUCHSCREENSetup.exe, then click on “ OK ” . (4) Select “ Yes ” to the question if this is the first time to run this setup. (5) When the “ InstallShield Wizard ” appears, click on “ Next ” to continue.
Installing Software Drivers 6- 19 (11) If you need 4,9,16,25 dot of the calibrate, we suggest select “ Advanced Calibration ” button to calibrate. (12) Click on the four sides red points and plus sign on the screen to calibrate your “ PENMOUN T ” pen to start using your MIL-BOOK 100’s Touchscreen.
Installing Software Drivers 6- 20.
Caring for the computer 7- 1 CHAPTER 7 Caring for the Computer Taking good care of your computer will ensure a trouble-free operation and reduce the risk of damage to your computer.
Caring for the Computer 7- 2 Protecting the Computer To safeguard the integrity of your computer data as well as the computer itself, you can protect the computer in several ways as described in this section. Using the Password The power-on password protects your computer against unauthorized use.
Caring for the computer 7- 3 Taking Care of the Computer Location Guidelines l Use the computer where the temperature is between 0 ° C to 55 ° C . l Avoid placing the computer in a location subject to high humidity, extreme temperatures, mechanical vibration, direct sunlight, or heavy dust.
Caring for the Computer 7- 4 Cleaning Guidelines l Never clean the computer with its power on. l Use a soft cloth moistened with water or a non-alkaline detergent to wipe the exterior of the computer. l Gently wipe the display with a soft, lint-free cloth.
Caring for the computer 7- 5 When Traveling l Before traveling with your computer, make a backup of your hard disk data into floppy disks or other storage devices. As an added precaution, bring along an extra copy of your important data. l Make sure the battery pack is fully charged.
Caring for the Computer 7- 6.
Troubleshooting 8- 1 CHAPTER 8 Troubleshooting Hardware, software, or a combination of both can cause computer problems. When you encounter any problem, it might be a typical problem that can easily be solved. This chapter tells you what actions to take when solving common computer problems.
Troubleshooting 8- 2 Preliminary Checklist Here are helpful hints to follow before you take further actions when you encounter any problem: l Try to isolate which part of the computer is causing the problem. l Make sure that you turn on all peripheral devices before turning on the computer.
Troubleshooting 8- 3 Solving Common Problems For easy reference, the problems are divided into these categories. Problem Type Go to Battery problems P. 8-4 CD/COMBO drive problems (on optional docking station) P. 8-5 Display problems P. 8-5 Floppy disk drive problems (on optional docking station) P.
Troubleshooting 8- 4 Battery Problems The battery does not charge (Battery Charge LED indicator does not light orange). l Make sure that the AC adapter is properly connected. l Make sure that the battery is not too hot – gets above 55 o C or too cold – below 0 o C.
Troubleshooting 8- 5 CD/COMBO Drive Problems (on optional docking station) The CD/DVD drive cannot read a CD. l Make sure that the CD is correctly seated in the tray, with the label facing up. l Make sure that the CD is not dirty. Clean the CD with a CD cleaning kit, available in most computer stores.
Troubleshooting 8- 6 l The brightness level might be too low. Increase brightness by pressing Fn + F6 . l The display output might be set to an external monitor. To switch the display back to the LCD, press Fn + F9 . l Reset the computer by pressing the Ctrl + Alt + Del keys if you are using an external keyboard.
Troubleshooting 8- 7 The external monitor displays nothing. l Make sure that the monitor is turned on. l Make sure that the monitor ’ s signal cable is properly connected. l Check if the Setup item Display Mode on the Main menu of the SCU program is configured correctly.
Troubleshooting 8- 8 The disk drive cannot read a floppy disk. l Make sure that the floppy disk is formatted. l Make sure that you are reading the correct drive. Hardware Device Problems The computer does not recognize a newly installed device. l The device may not be correctly configured in the SCU program.
Troubleshooting 8- 9 The hard disk drive in-use indicator glows without blinking. l The data files stored on the hard disk drive may be fragmented. Use a tool such as Window ’ s Disk Defragmenter to defragment the files. Keyboard, Mouse and Touchpad Problems The keyboard does not respond.
Troubleshooting 8- 10 LAN /Wireless LAN Problems I cannot access the network. l Make sure that the LAN driver is correctly installed. l Make sure that the LAN cable is properly connected to the RJ-45 connector and the network hub. l Make sure that the network configuration is appropriate.
Troubleshooting 8- 11 WARNING: COM3 is reserved for use by the touchscreen, do not disable it. If COM1/2 is disabled and COM3/4 is enabled on the SCU Setup (refer to chapter 5), upon booting system would recognize the enabled COM3/4 and designate it as COM1/2.
Troubleshooting 8- 12 The computer does not enter Standby or Suspend mode with the Fn + F10 hot keys. l You might be using a PC Card that prevents the computer from entering Suspend mode. To enter the mode, stop the communication program and then remove the card or stop the card.
Troubleshooting 8- 13 Sound Problems No sound is produced. l Make sure that the volume control is not set too low. l Make sure that the audio driver is correctly installed. l Make sure that the computer is not in Standby mode. l If using an external speaker, make sure that the speaker is properly connected.
Troubleshooting 8- 14 l If you are using the battery power, make sure that the battery is not discharged. When you turn on the computer, it stops after POST. l Restart your computer. The message “ Operating system not found ” appears on the screen after you turn on the computer.
Troubleshooting 8- 15 Other Problems The date /time is incorrect. l Correct the date and time via the operating system or SCU program. l After you have performed everything as described above and still have the incorrect date and time every time you turn on the computer, the RTC (real-time Clock) battery is at the end of its life.
Troubleshooting 8-16.
Specifications A-1 APPENDIX R Specifications NOTE: Specifications are subject to change without any prior notices. Parts Specifications CPU Intel Pentium M Processor LV1.
Specifications A- 2 Parts Specifications On computer RJ-11 fax/modem port, serial ports, VGA, Mic-in, Line-out, RJ-45 port, USB port, I/O ports Docking station (option) USB ports, serial ports, VGA, E.
An important point after buying a device TAG 100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought TAG 100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data TAG 100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, TAG 100 you will learn all the available features of the product, as well as information on its operation. The information that you get TAG 100 will certainly help you make a decision on the purchase.
If you already are a holder of TAG 100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime TAG 100.
However, one of the most important roles played by the user manual is to help in solving problems with TAG 100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device TAG 100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
