Instruction/ maintenance manual of the product WA301 Bard
Go to page of 19
Models: W A301, W A361 WALL MOUNTED PACKAGED AIR CONDITIONER INST ALLA TION INSTRUCTIONS Manual No.: 2100-192M Supersedes: 2100- 192L File: V olume III , T ab 16 Date: 05-13-02 Bard Manufacturing Company Bryan, Ohio 43506 Since 1914...Moving ahead just as planned.
Content s i T ables T able 1 Electrical S pecifications ........................ 2 T able 2 Dimensions of Basic Unit ...................... 3 T able 3 Electric Heat T able ................................ 4 T able 4 Operating V olt age Range .........
Manual 2100-192 Page 1 Getting Other Information and Publications These publications can help you install the air conditioner or heat pump. You can usually find these at your local library or purchase them directly from the publisher. Be sure to consult current edition of each standard.
Manual 2100-192 Page 2 WALL MOUNT GENERAL INFORMA TION AIR CONDITIONER WALL MOUNT MODEL NOMENCLATURE W A 3 6 1 – A 1 0 X XXXXA VOL TS & PHASE A - 230/208/60/1 B - 230/208/60/3 C - 460/60/3 MODEL.
Manual 2100-192 Page 3 MIS-1262 FIGURE 1 UNIT DIMENSIONS FRONT VIEW BACK VIEW SIDE VIEW * Optional top outlet (factory installed only) for WA30 and WA36 models only. TABLE 2 DIMENSIONS OF BASIC UNIT (NOMINAL) l e d o M h t d i W ) W ( h t p e D ) D ( t h g i e H ) H ( y l p p u Sn r u t e R EF G I JKL M N O P Q RS T A BCB 0 3 A W 6 3 A W 0 0 2 .
Manual 2100-192 Page 4 TABLE 3 ELECTRIC HEAT TABLE s l e d o M A - 1 0 3 A WB - 1 0 3 A WC - 1 0 3 A WA - 1 6 3 A WB - 1 6 3 A WC - 1 6 3 A W 1 - V 0 4 21 - V 8 0 23 - V 0 4 23 - V 8 0 23 - V 0 6 41 -.
Manual 2100-192 Page 5 SHIPPING DAMAGE Upon receipt of equipment, the carton should be checked for external signs of shipping damage. If damage is found, the receiving party must contact the last carrier immediately, preferably in writing, requesting inspection by the carrier’s agent.
Manual 2100-192 Page 6 The blank-off plate is available upon request from the factory and is installed in place of the fresh air damper shipped with each unit. CONDENSATE DRAIN A plastic drain hose extends from the drain pan at the top of the unit down to the unit base.
Manual 2100-192 Page 7 INST ALLA TION INSTRUCTIONS W ARNING Fire hazard can result if 1/4 inch clearance to combustible materials for supply air duct is not maintained. See Figure 3. WALL MOUNTING INFORMATION 1. Two holes, for the supply and return air openings, must be cut through the wall as shown in Figure 3.
Manual 2100-192 Page 8 The electrical data lists fuse and wire sizes (75ºC copper) for all models, including the most commonly used heater sizes. Also shown are the number of field power circuits required for the various models with heaters.
Manual 2100-192 Page 9 FIGURE 3 MOUNTING INSTRUCTIONS NOTE: It is recommended that a bead of silicone caulking be placed behind the side mounting flanges and under the top flashing at the time of installation. Side section view of supply air duct for wall mounted unit showing 1/4 inch clearance to combustible surfaces.
Manual 2100-192 Page 10 FIGURE 5 WALL-MOUNTING INSTRUCTIONS MIS-549 FIGURE 6 WALL-MOUNTING INSTRUCTIONS MIS-548 SEE FIGURE 3 – MOUNTING INSTRUCTIONS SEE UNIT DIMENSIONS, FIGURE 1, FOR ACTUAL DIMENSI.
Manual 2100-192 Page 11 MIS-550 FIGURE 7 COMMON WALL-MOUNTING INSTALLATIONS.
Manual 2100-192 Page 12 FIGURE 8 LOW VOLTAGE WIRING MIS-1373C.
Manual 2100-192 Page 13 IMPORTANT INSTALLER NOTE For improved start-up performance, wash the indoor coil with a dishwasher detergent. CRANKCASE HEATERS All units are provided with some form of compressor crankcase heat. All single and three phase models have an insertion well-type heater located in the lower section of the compressor housing.
Manual 2100-192 Page 14 ADJUSTMENTS Adjustable Delay on Make and Delay on Break Timer The potentiometer is used to select Delay on Break time from 30 seconds to 5 minutes. Delay on Make (DOM) timing on power-up and after power interruptions is equal to 2 minutes plus 10% of Delay on Break (DOB) setting: 0.
Manual 2100-192 Page 15 TROUBLESHOOTING FAN BLADE SETTING DIMENSIONS Shown in the drawing below are the correct fan blade setting dimensions for proper air delivery across the outdoor coil.
Manual 2100-192 Page 16 TABLE 11 MAXIMUM ESP OF OPERATION ELECTRIC HEAT ONLY l e d o Mt e l t u O t n o r Ft e l t u O p o T W K w o L d e e p S h g i H d e e p S w o L d e e p S h g i H d e e p S 0 0 A 5 0 A 8 0 A 0 1 A 5 1 A 0 5 . 0 5 . 0 5 . 5 4 . 5 3 .
Manual 2100-192 Page 17 W A301-A W A301-B W A301-C W A361-A W A361-B W A361-C TABLE 13 OPTIONAL ACCESSORIES L E D O MN O I T P I R C S E D 5 0 A - 3 0 A W H E s e g a k c a P r e t a e H 1 XX 8 0 A - .
An important point after buying a device Bard WA301 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bard WA301 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bard WA301 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bard WA301 you will learn all the available features of the product, as well as information on its operation. The information that you get Bard WA301 will certainly help you make a decision on the purchase.
If you already are a holder of Bard WA301, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bard WA301.
However, one of the most important roles played by the user manual is to help in solving problems with Bard WA301. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bard WA301 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
