Instruction/ maintenance manual of the product 2X10T SWR Sound
Go to page of 16
W orkingman’s Series BASS SPEAKER ENCLOSURES OWNER’S MANUAL WORKINGMAN’S 1X10T WORKINGMAN’S 2X15T WORKINGMAN’S 2X10T WORKINGMAN’S 4X10T WORKINGMAN’S TOWER SWR • CORONA, CA • USA.
W orkingman’s Series Bass Speaker Enclosures • 1 INTRODUCTION Congratulations on your purchase of an SWR WorkingMan’s Series bass speaker enclo- sure. By placing an SWR cabinet in your bass amplification system you have made a sound desicion that could ver y well be the best of your life! Just a little humor there, but tr ue nonetheless.
W orkingman’s Series Bass Speaker Enclosures • 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 T able Of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 General Infor mation . . . . . .
W orkingman’s Series Bass Speaker Enclosures • 3 GENERAL INFORMA TION Connection Only one amplifier at a time can be connected to your W orkingMan’s speaker enclosure. DO NOT plug two amplifiers into one speaker enclosure, as it will not work and may damage your system.
W orkingman’s Series Bass Speaker Enclosures • 4 INPUT P ANEL DIAGRAM All Models (except W orkingMan’s T ower) INPUT P ANEL DIAGRAM W orkingMan’s T ower Tweeter Attenuator Switch 1 / 4" I.
W orkingman’s Series Bass Speaker Enclosures • 5 WORKINGMAN’S 1X10T Specifications Description: 1x10 and Tweeter Speaker Enclosure Power Handling: 100 watts RMS Impedance: 8 ohms F r equency Res.
W orkingman’s Series Bass Speaker Enclosures • 6 WORKINGMAN’S 1X15T Specifications Description: 1x15 and Tweeter Speaker Enclosure Power Handling: 200 watts RMS Impedance: 8 ohms Frequency Respo.
W orkingman’s Series Bass Speaker Enclosures • 7 WORKINGMAN’S 2X10T Specifications Description: 2x10 and Tweeter Speaker Enclosure Power Handling: 200 watts RMS Impedance: 8 ohms Frequency Response & SPL: 98 dB SPL @ 1W1M (–3db @ 63 Hz and 18.
W orkingman’s Series Bass Speaker Enclosures • 8 WORKINGMAN’S 4X10T Specifications Description: 4x10 and Tweeter Speaker Enclosure Power Handling: 400 watts RMS Impedance: 8 ohms Frequency Respo.
W orkingman’s Series Bass Speaker Enclosures • 9 WORKINGMAN’S TOWER Specifications Description: 8x10 and Tweeter Speaker Enclosure Power Handling: 800 watts RMS Impedance: 4 ohms Frequency Response & SPL: 93 dB @ 1W1M (–3dB 60 Hz & 13.
W orkingman’s Series Bass Speaker Enclosures • 10 WORKINGMAN’S TOWER (continued) Tweeter Attenuator Control The lar ge dial found on the input panel of the cabinet is the Tweeter Attenuator Contr ol (see dia- gram, page 4). This control is used to adjust the level of high fr equency signal present at the tweeter .
W orkingman’s Series Bass Speaker Enclosures • 11 IMPEDANCE: A GENERAL OVER VIEW The following ter ms will be helpful in understanding the infor mation in this section: Impedance: The resistance of a device to the flow of alter nating cur r ent. Often used to rate the resistance of a speaker's voice coil.
W orkingman’s Series Bass Speaker Enclosures • 12 IMPEDANCE (continued) one 8 ohm enclosure, you know you can add one mor e 8 ohm speaker safely (8 divided by 2 = 4). Although much less common, you could also add one, or even two, 16 ohm cabinets: two 16 ohm cabinets in parallel have the same total impedance as one 8 ohm speaker .
W orkingman’s Series Bass Speaker Enclosures • 13 than one cabinet, check all cable connections in the chain. If you then suspect that the problem may be a bad cable, you can use a 9 volt batter y as a cable-tester .
W orkingman’s Series Bass Speaker Enclosures • 14 SWR LIMITED WARRANTY SWR W orkingman’s Series Speaker Enclosures are w ar ranted to the original consumer pur chaser for ONE YEAR fr o m the dat.
W orkingman’s Series Bass Speaker Enclosures • 15 IMPORT ANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER OR BACK.
An important point after buying a device SWR Sound 2X10T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought SWR Sound 2X10T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data SWR Sound 2X10T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, SWR Sound 2X10T you will learn all the available features of the product, as well as information on its operation. The information that you get SWR Sound 2X10T will certainly help you make a decision on the purchase.
If you already are a holder of SWR Sound 2X10T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime SWR Sound 2X10T.
However, one of the most important roles played by the user manual is to help in solving problems with SWR Sound 2X10T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device SWR Sound 2X10T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
