Instruction/ maintenance manual of the product POL 10550 Swisher
Go to page of 16
50 ” FRONT MOUNT/ TRAILMOWER OWNER’S MANUAL 1602 CORPORATE DRIVE, P.O. BOX 67, WARRENSBURG, MISSOURI 64093 PHONE 660-747-8183 FAX 660-747-8650 MODEL NO. Manufacturing quality lawn care equipment since 1945 Assembly Operation Service and Adjustment Repair Parts Made In The USA Rev.
SAFETY PRECAUTIONS • Read the manual. Learn to operate this machine safely. • Always disconnect the spark plug wire and place the wire where it cannot contact the spark plug, to prevent accidental starting the engine when setting up, trans porting, adjusting or making repairs.
• Turn off the blades when not mowing. Before leaving the machine, turn off the blades and stop the engine. • Watch for traffic when operating near or crossing roadways. • Do not operate the mower if it has been dropped or damaged in any manner or if the mowe r vibrates excessively.
MOWER MAINTENANCE GENERAL RECOMMENDATIONS The warranty on this trailmower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain unit as instructed in this manual.
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship.
OPERATING YOUR MOWER INTENDED USE This trail mower is designed to produce a quality finish cut on lawns, golf courses, etc. It is not designed to clear brush or cut saplings. Your mower be should pushed in front of or be towe d behind an ATV, a golf cart, lawn tractor, or another similar approved vehicle.
STARTING THE ENGINE • See engine manufacturer’s instructions for the type and amount of oil and fuel used. Engine must be level to accurately check and fill oil. Do not overfill. • Park vehicle and mower on a level surface, set the vehicle p arking brake, and disengage blades.
STOP MOWING • Bring vehicle to a full st op. • Disengage clutch lever by moving lever to center position. • Turn key switch to “OFF” position.
SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Order by part number from Swisher Mower and Machine Co. Inc. OD33 – Speed Decal OD43 – Flying Debris Decal OD45 – Warning Deca.
FRAME ASSEMBLY FIGURE 1 Item No. Description Part # 1 Frame Weldment 5107S 2 Caster Weldment 5072 3 Tire & Wheel NO Tread 4.10x3.5-5 5057 4 Bearing, Flanged 3/4 ID CB58 5 3/4 Push Nut BLK Plastic NB-687 6 3/4ID X 1 1/4OD 10 GA.
DECK ASSEMBLY FIGURE 2 See Detail (Page 12) See Detail (Page 14) See Detail (Page 14) 14 5 14 8 4 12 14 18 2 17 9 16 14 15 1 4 13 6 19 34 10 11 26 7 20 Item # Description Part # Item # Description Par.
MOTOR BASE ASSEMBLY ENGINE SET-UP FIGURE 4 Item No. Description Part # 13 10 1/2 HP B&S Engine N/A 14 3/8-24 X 1 Engine Bolt Locktite NB-238N 15 Washer Belleville 699 16 1/4 X 1 Key Stock 9031 17 Engine Pulley- 5.5" 688 18 Engine Pulley Spacer Short 689S 19 Engine Pulley Spacer Long 689L 13 19 16 17 18 15 14 Figure 3 Item No.
BELT CONFIGURATION Figure 5 3752 (112 ” Belt) T 239 (39 ” Belt) 13.
1 2 2 14 Blade Driver Assy. 9058- 5.75 ” (Center Shaft) 9018- 4.25 ” (Outer Shafts) 10 7 11 8 4 10 15 16 5 6 3 9 13 12 Figure 6 BLADE DRIVER SET-UP 14 7 Outer Blade Driver Configuration Center Blade Driver Configuration Item No.
Console Assembly Wiring Diagram Figure 7 Figure 8 WHBP50 (Complete Wiring Harness) Item No. Description Part # 1 Console Weldment 5136TK 2 Clutch Cable Clevis 9023 3 T Handle 4463TK 4 Link for Console.
OWNER’S MANUAL MODEL NO. Each mower has its own model number. Each engine has its own model number. The model number for the mower will be found on the right hand side of the drive belt housing. The model number for the engine will be found on the top of the blower fan housing.
An important point after buying a device Swisher POL 10550 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Swisher POL 10550 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Swisher POL 10550 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Swisher POL 10550 you will learn all the available features of the product, as well as information on its operation. The information that you get Swisher POL 10550 will certainly help you make a decision on the purchase.
If you already are a holder of Swisher POL 10550, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Swisher POL 10550.
However, one of the most important roles played by the user manual is to help in solving problems with Swisher POL 10550. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Swisher POL 10550 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
