Instruction/ maintenance manual of the product FC-10 Swisher
Go to page of 12
Owner ’s Manua l FC-10 IMPORTANT Read and foll ow all Safety Preca utions and Instr uctio ns Before Operati ng this Equipme nt. Made In CHINA 1602 CORPORA TE DRI VE PO B OX 67 W ARRENSBURG, MISSOURI 64093 PH 660. 747. 8183 FAX 660. 747. 8650 swish erinc .
LIMITED WARRA NTY The manufacturer’s warranty to the origin al consumer purchaser is: This product is free from defects in materials and workmanshi p for a period of One (1) year from the date of purchase by the original consu mer purchaser.
Pre-Ass embly In structio ns For easy assembly , follow all directions step by s tep. Open all boxes before beginning to assemble. Ap proximate assembly time is: 1 .5 to 3 hours Helpful TIP: Read all instructions be fore sta rting to assemble ca rt. Check P arts and Hardware : Group tog ether and check that all hardware and parts are include d.
Complete Parts Ill ustration for Trailer Cart Page 4.
Step 1: Att aching Fro nt Cross Brac e Position the two Bottom Panels(#1) as show n in Figure 1 below. Attach the F ront Cross Brace(#2) to the Bottom Panels using 4 (# 21) Bolts, 4 (#23) W ashers, and 4 (#24) Nuts.
Step 3: Attaching the Tongue S upport Attach the T ongue Supp ort(#3) to the Bott om Panels as shown in F igure 3 using 2 (#22) Bolts, 2 (#23) Washers, and 2 (#24) Nuts.
Step 6: Attaching Whe el Axle and Tires Set Hitch Tongue(#10) in place as shown below before inserting W heel Axle(#5) throu gh Wheel Axle Support(#4) . Next, inse rt the W heel Axle (#5) into the Wheel Axle Support(#4 ), and through the holes in the Tongue(#10) as show n in Figure 6.
Step 8: Ins talling the Hitch Pin Bracket Install the Hitch Pin Bracket(#11) in the back two holes of the Hitch Tongue(#10) using 2 (#25) Bolt s, 2 (#23) W ashers, and 2(#24) Nuts. Refer to Figure 8. Place Hitch Pin(#28) in the front hole, using Cotter Pin(#27) to hold in place.
Step 11: Secure Rear Cross Brace Bolt Rear Cross Brace(#12) to Bot tom Panels(#1) using 6 (#21) Bolts, 6 (#23) W ashers, and 6 (#24) Nuts. See Figure 11 for bolt locations.
Final Ste p: Attaching Tail Ga te with Latches First attach the two Tailgate Latches(#18) to the inside of the Tailgate(#20) using 2 (#21) Bolts, 2 (#23) W ashers, and 2 (#24) Nuts for each Tailgate Latch(#18). Next, insert the Tailgate Pins(#19) into the holes on the bottom part of the Tailgate.
Operation/ Maintenance NOTE S: Operation notes - A full capacity load is 500 pounds , DO NO T exceed rated capacity. Cart only to be used with lawn tracto r or ATV. Cart is not to for highw ay use. Do not exceed 10 mph when towing. Maintenance notes- On a re gular basis, check that tires are inflated properly .
swish erinc .com MANUFAC TURING Q UALITY LAWN CAR E EQUIP MENT S INCE 1945 WHEN ORDERING PARTS, PLEASE HAVE THE FOLLOWING INORMATION A VAILABLE: * PRODUCT – ______ __________ * SERIAL NUMBER - _ ___.
An important point after buying a device Swisher FC-10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Swisher FC-10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Swisher FC-10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Swisher FC-10 you will learn all the available features of the product, as well as information on its operation. The information that you get Swisher FC-10 will certainly help you make a decision on the purchase.
If you already are a holder of Swisher FC-10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Swisher FC-10.
However, one of the most important roles played by the user manual is to help in solving problems with Swisher FC-10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Swisher FC-10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
