Instruction/ maintenance manual of the product R9843051 Barco
Go to page of 10
S e r v e r U p g ra d e K i t f o r B a rc o i Q P ro Installation M anual R9843050 R9843051 R5976950/00 15/02/2006.
Barco nv Presentations Noordl aan 5, 8520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.35.86.51 E-mail: presentations.bid@barco.com Visit us at the web: www.
1. Kit descri ption 1. KIT DESCRIPTION Overview • Description • Kit contents 1.1 Description Introduction In order to increase server performance, a new server upg rade kit has been developed for .
1. Kit description Image 1-1 Image 1-2 Image 1-3 2 R5976950 SERVER UPGRADE KIT FO R BARCO IQ PRO 15/02/2006.
2. Kit installation 2. KIT INST ALLA TION Installati on The installation of the new server involves different steps (explained in detail further on). 1. Physical installation, see procedure below 2. Performing the upgrade tool (see InfoT640) 3. Firmware upgrade to V3.
2. Kit installation Image 2-2 side screw 4. T ake the server out of the input box Image 2-3 Server removed from the input bo x 2.2 Removing the vid eo inputs (layer 1 and layer 2) How to remove the video inputs ? 1. Refer to the service manual for the detailed p rocedure 2.
2. Kit installation Image 2-4 Resistor R80 location. R5976950 SERVER UPGRADE KIT FOR BARCO IQ PRO 15/02/20 06 5.
2. Kit installation Image 2-5 Resistor R71 location. (un)Solde r tips • Insure that the Soldering Iron Tip is clean, in good condition and is fully inserted into the heater . • Use the appropriate Tip and T emperature. • Do not exert force on the land (pa d) during the (un)soldering opera tion.
2. Kit installation Image 2-6 2. Place the new grid and tighten the screws. 2.5 Reassemblin g the input box How to mount the Vide o inputs (layer 1 and layer 2) on the new front plate ? 1. Perform above removal procedure in the reverse directions How to mount the s upport plate ? 1.
2. Kit installation Note that th e PCMCIA input plat e (little op ening plate moun ted on the PCMCIA input ) is not delive red with the new front plate. Therefore remove it from the old front pla te (by removing th e 2 small screws) and m ount it on the new front pla te.
An important point after buying a device Barco R9843051 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Barco R9843051 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Barco R9843051 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Barco R9843051 you will learn all the available features of the product, as well as information on its operation. The information that you get Barco R9843051 will certainly help you make a decision on the purchase.
If you already are a holder of Barco R9843051, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Barco R9843051.
However, one of the most important roles played by the user manual is to help in solving problems with Barco R9843051. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Barco R9843051 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
