Instruction/ maintenance manual of the product 1500 Sun Microsystems
Go to page of 15
Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U .S.A. 650-960-1300 Send comments about this document to: docfeedback@sun.com Sun Blade™ 1500 Ser vice , Diagnostics , and T roub leshooting Manual Pa r t No .
Chapter 11 Replacing the Motherboard and Associated Components 11-3 FIGURE 11-1 DIMM Location and Identification Depending upon the configuration of your workstation, you can either add or replace memory . In either case, the new DIMMs must meet the Sun workstation requir ements.
Chapter 13 Replacing Chassis Components 13-15 Y ou can also view an animated version of these instructions by clicking on this film icon. 13.3.1 Identifying the Rear Fan The front and r ear fans on the Sun Blade 1500 workstation are contained in green brackets.
12-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 12-13 Smart Car d Reader Location and Identification 12.3.2 Removing the Smart Car d Reader 1.
Chapter 14 Replacing Internal Cables 14-7 14.2.1 Identifying the DVD-ROM Drive Interface Cable The DVD-ROM has separate power and interface cables. The power cable is a Y cable that connects to the motherboard at IDE PWR and the other ends to the hard drives and DVD-ROM drive.
Chapter 14 Replacing Internal Cables 14-15 3. Disconnect the IDE power cables from the upper hard drive HDD0 . See FIGURE 14-12 . FIGURE 14-12 Disconnecting the IDE Power Cable Fr om the Hard Drive(s) 4. If installed, disconnect the IDE power cable from the lower hard drive HDD1 .
14-10 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 14.3 Replacing the Har d Drive Interface Cable This section describes removal and installation of the hard drive interface cables.
Chapter 11 Replacing the Motherboard and Associated Components 11-5 FIGURE 11-3 Pressing the Catch on the Rear Fan Bracket 4. Slide the duct up until it is f lush with the edge of the rear fan bracket. See FIGURE 1 1-4 . FIGURE 11-4 Sliding the Duct Up 5.
Chapter 10 Preparing to Replace Components 10-15 FIGURE 10-9 Bezel Location and Identification 3. Release the lower mounting tabs. Carefully move the lower pair of mounting tabs apart, and then push them forwar d slightly .
11-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 11-15 Pr essing Down on the Clip Latch b. Slide the clip to unhook the end opposite the latch. This relieves clip pr essure. c. Rotate the clip away from the CPU fan and heatsink assembly and lift it off the locking ring.
11-22 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 1 1.3.1 Identifying the Battery FIGURE 1 1-23 shows the location of and identifies the battery . FIGURE 11-23 Battery Location and Identif ication T ABLE 1 1- 1 lists the battery specifications.
11-36 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 11-34 Identifying the PCI Car d Slots 3. Swing out the PCI card support. Squeeze the inside tabs together and swing the PCI card support out. See FIGURE 1 1-35 .
Chapter 11 Replacing the Motherboard and Associated Components 11-45 FIGURE 11-42 Removing Cables Fr om the Routing Clips 9. Disconnect the power and signal cables. Disconnect the following power and signal cables from the corresponding motherboard connectors and set them out of the way of the motherboard.
Chapter 13 Replacing Chassis Components 13-45 FIGURE 13-48 Removing the PCI Car d Support Note – Do not use the chassis cross brace as a handle. Proceed to “Installing the PCI Card Support” on page 13-45. Note – Do not operate the workstation without the PCI card support installed.
Chapter 15 Finishing Component Replacement 15-9 FIGURE 15-8 Reconnecting the Keyboard, Mouse, Monitor , and Network Connections 2. Reconnect any other external peripherals.
An important point after buying a device Sun Microsystems 1500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sun Microsystems 1500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sun Microsystems 1500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sun Microsystems 1500 you will learn all the available features of the product, as well as information on its operation. The information that you get Sun Microsystems 1500 will certainly help you make a decision on the purchase.
If you already are a holder of Sun Microsystems 1500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sun Microsystems 1500.
However, one of the most important roles played by the user manual is to help in solving problems with Sun Microsystems 1500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sun Microsystems 1500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
