Instruction/ maintenance manual of the product FF-7 Summit
Go to page of 12
FELIX ST OR CH, INC. SUMMIT APPLIANCE DIVISION® INSTRUCTION MANUAL FOR MODEL(S): All Variations of the FF-6 All Variations of the FF-7 & All Variations of the SCR-600L/SCR-600BL ALL-REFRIGERATOR.
Write the model and serial numbers here: Model#_____________________ Serial #___________________ Find these numbers on the back of the unit Table of Contents Before Putting into Use … 3 IMPORTANT Disposing of worn out Appliance…. 4 Placing and Installatio n Choosing the right Place………………….
*Before Putting Into UsE* Before connecting the appliance to the power supply, leave it standing for about 2 hours, this will reduce the possibility of malfunctions in the cooling system due to transport handling. Clean the appliance thoroughl y; especially in the in terior (See Cleaning and Maintenance).
IMPORTANT If you bought this appliance to repla ce an old one equipped with a lock that cannot be opened fro m inside (lock, bolt), make sure that the lock is broken. This will make it impossib le for children to lock themselves inside the appliance and suffocate.
PLACING AND INSTALLATION It is important to make sure th e appliance is leveled evenly to prevent falling . Two spacers attached to the app liance must be fitted onto the upper edge of the condenser, thus preventing the appliance from being installed too close to the wall.
Operation control How To Adjust The Thermostat The refrigerator is controlled with a thermo stat knob located insi de unit, towards the right-hand corner. Turn the knob clockwise from the STOP (0) position toward higher numbers for colder temperatures.
Storing Fresh Foods Foods to be stored in the refrigerator should be properly packed as to prevent mixing various moisture degrees and odors (in polyethylene bags or sheet, alum inum foil, wax paper, covered containers or bottles). Never store any inflammable, volatile or explosive substances.
There is no need to defrost the refrigerator, because the ice depositing on the inner back wall is defrosted automatica lly. Ice may deposit on the inner b ack wall during the compressor op eration; l.
Door swing reversal ( Stainless steel models with towel bar handles do not have reversible doors.) If you find the direction of opening the door on your appliance inconvenient, you can change it. Holes on the opposite side have already been prepared at the factory 1.
Adjusting the Level legs The Professional units (those with a BI suffix in model number ) have 4 adjustable level legs. By turning the legs counter-clockwise you can increase the height of the unit up to 34” inches high or you may decrease the height to about 33” inches by turning clockwise.
Ice Formation on the Inner Rear Wall Possible Causes * The door does not seal well (clean th e gasket if it is contaminated, or replace it if it is damaged). *The door was frequently open ed or it was left opened for too long. *The food stored in the refrigerator was warm.
. After starting the appliance, the operation of the compressor and the refrigerant flow may be louder and this does not mean something is wr ong with the appliance. The noise will reduce gradually. During the operation of the compressor, a liquid noise is heard and when the compressor is not operating a refrigerant flow is heard.
An important point after buying a device Summit FF-7 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Summit FF-7 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Summit FF-7 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Summit FF-7 you will learn all the available features of the product, as well as information on its operation. The information that you get Summit FF-7 will certainly help you make a decision on the purchase.
If you already are a holder of Summit FF-7, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Summit FF-7.
However, one of the most important roles played by the user manual is to help in solving problems with Summit FF-7. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Summit FF-7 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
