Instruction/ maintenance manual of the product 561 Sub-Zero
Go to page of 12
INSTALLATION INSTRUCTIONS •.
• -~~------------- PRE-INSTALLATION INSTRUCTIONS PRE-INSTALLATION SPECIFICATIONS PREPARATION FOR INSTALLATION Step 1 Prepare the finished rough opening to accept the installation of the Sub-Zero. NOTE: Carefully read the "Pre-Installation Specifications" chart below.
PRE-INSTALLATION INSTRUCTIONS Figure 5 COMPRESSION FITTING Figure 6 COMPRESSION FITTING SLAB FLOOR UNPACKING Step 5 Uncrate unit, remove wood base and discard the shipping bolts which secure the wood base to the bottom of the unit. Do not discard wood block and hardware to be used for blocking your unit.
INSTALLATION INSTRUCTIONS Figure 12 To block the unit, using the wood block and hardware provided, follow these steps. 1) Locate and mark two wall studs against the wall where the refrigerator is to be located. 2) Locate the proper height to clear the unit.
INSTALLATION INSTRUCTIONS INSTALLATION I AWARNING I Shut-off power to the wall outlet. Step 9 Unit is equipped with rollers. Plug into 15 amp grounded outlet and roll unit into desired position under the wood block or soffit and connect icemaker water line to unit.
INSTALLATION INSTRUCTIONS B) With standard Phillips screwdriver, remove door handle on freezer and refrigerator door (the door handles also act as a door trim), The Models 511 and 550 freezer door han.
INSTALLATION INSTRUCTIONS ElllARGE TO 3,0,," OI.UlE'TER Figure 21 Il I ~--~--~ SCREWOROIoIMET ~ p .... • .... 14".0 _ ..... 'i((j-- 1: ! UPPER QRILU S~~: P .
• INSTALLATION INSTRUCTIONS ~~'I." I '7'111" =- co =L t 17'/a" .. L .. .. - ~ wP" Figure 24 1) Drill three (3) 13 /60" holes through the middle trim of both units. NOTE: Product(s) must be leveled and squared before attempting this procedure.
INSTALLATION INSTRUCTIONS 2) Using the Loctite on the screws, install all 3 Chicago Screw Posts. 3) Inspect the units for level again. 4) Drill three (3) 3h6" holes (per specs in Figure 24) through both outer trims. 5) Using a '/a" drill bit, drill into the cabinetry for a pilot hole.
INSTALLATION INSTRUCTIONS STANDARD HANDLE RECESS SPECIFICATIONS PRODUCT SERVICE 1-- 8 -----1 FREEZER REFRIGERATOR PANEL PANEL T 14-- I c 1 E MODELS 532,542 AND 561 I---A---I T REFRIGERA10R T PANEL I 1- ~T c L.
INSTALLATION INSTRUCTIONS 3" 2" 1" -- -' 11 ---j ii ,~ n v I ~ 1'1." Panel Standard 1" Panel Full-Length 'I." Panel Handle 'h" Panel ~ '1.
THINK SAFETY! If you are storing or disposing of your old refrigerator, please do it safely. Read the enclosed safety booklet from the Association of Home Appliance Manufacturers. CHILD ENTRAPMENT ACCIDENTS CAN BE TRAGIC! '-' - = SUB-ZERO FREEZER CO.
An important point after buying a device Sub-Zero 561 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sub-Zero 561 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sub-Zero 561 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sub-Zero 561 you will learn all the available features of the product, as well as information on its operation. The information that you get Sub-Zero 561 will certainly help you make a decision on the purchase.
If you already are a holder of Sub-Zero 561, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sub-Zero 561.
However, one of the most important roles played by the user manual is to help in solving problems with Sub-Zero 561. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sub-Zero 561 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
