Instruction/ maintenance manual of the product PrimaSat II Strong
Go to page of 19
D i g i t a l S a t e l l i t e R e c e i v e r P r i m a S a t I I User manual.
.
.
PART 1 • English 1 English STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EC and 73/23EC; RoHS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change.
PART 1 • English 2 1.0 INTRODUCTION 1.1 Safety Instructions DO NOT INST ALL YOUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots.
PART 1 • English 3 English 1.3 Equipment Set-up W e recommend you consult a professional installer to set up your equipment. Otherwise, please follow the instructions below: Refer to the user manual of your TV and your antenna.
PART 1 • English 4 2. TV SCART T o connect to your TV set using a SCART cable. 3. S/PDIF COAX T o connect to the input of your digital audio amplifier . 4. Power Cord Y our receiver requires a mains voltage of 100~240 V AC (Auto- selectable), 50/60 Hz ±5%.
PART 1 • English 5 English 2.6 Using the Remote Control Fig. 4 T o use the remote control, point it towards the front of the digital receiver . The remote control has a range of up to 7 metres from the receiver at an angle of up to 60 degrees. The remote control will not operate if its path is blocked.
PART 1 • English 6 4.1.4 Auto Standby This option allows you to enable Auto Standby or to disable Auto Standby . Auto Standby will switch the receiver to standby automatically when it doesn’t receive commands from the remote control for a period of 3 hours.
PART 1 • English 7 English Select the RED button to Set W est Limit position you have reached. Select the GREEN button to Set East Limit position you have reached. d) Satellite positions Press pq to select the Position you like to use and press OK .
PART 1 • English 8 5.1 TV Press tu to move to Main Menu . In Main Menu press tu to move to TV and press OK to enter the TV menu. 5.1.1 TV Channels Use tu to reach the following sub-menus F av , Lock , Edit , Move , Sort , Skip , Delete and Search . With the BLUE button you can change the available group you would like to use.
PART 1 • English 9 English 5.1.1.7 Delete Press tu to select , then press pq to select the desired channel and OK to delete this channel. Press the YELLOW button to save and confirm or exit the pop up screen. With the GREEN button you can select the whole list to delete.
PART 1 • English 10 5.3.1 Gomoku Press pq to select Gomoku and press OK . Play the game Gomoku on your receiver . Use the on screen help tips to set and play the game. 5.3.2 Calendar Press pq to select Calendar and press OK . Use the on screen help tips to search in your Calendar .
PART 1 • English 11 English 5.4.2.3 OSD T ransparency Press tu to change settings for OSD T ransparency (1~ 8 ). 5.4.2.4 Banner Display Time Press tu to change settings for Banner Display Time ( 1sec , 3sec , 5sec , 10sec , 30sec , Always ). 5.4.2.5 Video Output Press tu to change settings for Video Output (RGB or CVBS).
PART 1 • English 12 5.4.5 Set Default Press pq to select Set Default and press OK . A pop-up screen will ask you: “ Set factory default? ”. Press OK or EXIT . Please be careful when using this function, as it will erase all the data and parameters you may have set earlier .
PART 1 • English 13 English W arning! NEVER disconnect the USB device from the receiver , the receiver from the main or switch the power OFF during the update/backup procedure.
PART 1 • English 14 10.0 TROUBLE SHOOTING There may be various reasons for occurring abnormal operation of the receiver . Check the receiver according to the procedures shown below . If the receiver does not work properly after checking it, please contact the dealer .
PART 1 • English 15 English 11.0 SPECIFICA TIONS Demodulator Modulation: QPSK Input Symbol Rate: 2~45 Ms/s SCPC & MCPC signals from C & KU band satellites Video Decoder Profile level: MPEG-2 MP@ML Input Rate: Max.
PART 1 • English 16 General Data Input V oltage Range: 100-240 V AC 50/60 Hz Power consumption: max 18 W , typ. 4.6 W Stand-by Power consumption: 0.50 W Operating T emperature: +0 ~ 40 °C Storage T emperature: -30 ~ 80 °C Operating Humidity Range: 10 ~ 85%, RH, Non-condensing Size (WxDxH): 180 x 130 x 45 mm W eight: ca.
An important point after buying a device Strong PrimaSat II (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Strong PrimaSat II yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Strong PrimaSat II - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Strong PrimaSat II you will learn all the available features of the product, as well as information on its operation. The information that you get Strong PrimaSat II will certainly help you make a decision on the purchase.
If you already are a holder of Strong PrimaSat II, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Strong PrimaSat II.
However, one of the most important roles played by the user manual is to help in solving problems with Strong PrimaSat II. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Strong PrimaSat II along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
