Instruction/ maintenance manual of the product (F) - 2 Storageflex
Go to page of 16
INST ALLER / CONSUMER SAFETY INFORMA TION Please read this manual before installing and using the heater . W ARNING: If the infor mation in this manual is not followed exactly , a fire or explosion may result causing pr operty damage, personal injury or loss of life.
2 General Information SAFETY : Accidents are always tragic especially because so many of them could have been prevented with a little care and attention. These are some basic good practices we hope you will follow for safe use of your gas fired room heater .
3 RMC-LCNG, RMC-LCLP , RMC-LING, RMC-LILP Specifications Models (Manual & Thermostat) Gas T ype Input Rating (Btu/Hr) Variable Regulator Pressure Setting Inlet Gas Supply Pressure Size of Heater Weight Min. Max Min. Max RMC-LC30NG Natural 15,000 30,000 4.
4 Installation • This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air . • This hea ter must have fresh air for proper operation. If not, poor fuel combustion could result.
LOCA TING THE HEA TER 5 PREP ARING FOR INST ALLA TION 1. Remove hea ter from carton 2. Remove all protective packa ging applied to hea ter for shipment. 3. Check hea ter for any shipping damage. If heater is dama ged, promptly inform dealer/distributor .
6 FLOOR INST ALLA TION 1. Hea ter may only be installed on a noncombustible flat surface. Where the flooring is carpeting, tile or of other combustible material other than wood flooring, maintain the .
7 Installation should be done by a qualified ser vice person. Before connecting the appliance, turn off all gas appliances. Close the main gas valve a t the gas meter or LP tank. Make certain there is good ventilation where the installation will be made.
8 Operation Instructions FOR YOUR SAFETY - READ THIS SECTION BEFORE LIGHTING A. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to floor because some gas is heavier than air and will settle on the floor .
9 T urning Heater Off Push in gas control knob slightly and turn c lockwise to "OFF" position. Do not force. T urning Burner Only Off (Pilot stays lit). T urn control knob clockwise to the PILOT position. C AUTION: Do not try to adjust heating levels by using the manual shut-off valve.
10 Problem P ossible Cause What T o Do When control knob is pressed in and turned counterc lockwise to ignition, there is no spark at ODS pilot. 1. Ignitor electrode positioned wrong. 2. Ignitor electrode broken. 3. Ignitor cable pinched or broken. 4.
11 Problem P ossible Cause What T o Do Hea ter produces a clicking noise just after burner is lit or turned off. 1. Metal expanding and contracting. 1. This is common with heaters. If noise is excessive, contact a qualified ser vice technician. Gas odor even when control knob is in OFF position.
12 Item/Model Number RMC-LI06NG/LP RMC-LI10NG(T)/LP(T) RMC-LI18NG(T)/LP(T) RMC-LI30NG(T)/LP(T) 1. Lower Heat Cover LI10LP-01-01-02 LI10LP-01-01-02 LI18LPT -01-01-03 LI30NG-01-01-02 2. Guard Assembly LC10NG-01-04 LC10NG-01-04 LI18LPT -01-04 LC30NGTF-01-04 3.
13 CFM Home Products reserves the right to make changes in design, ma terials, specifications, prices and discontinue colors and products at any time, without notice.
14 The following accessories are available from your local distributors/dealer . Each accessor y comes with a separate installation instruction. Be sure to read each instruction thoroughly before installa tion.
15 Accessories continued C AUTION: Damaged power cord can cause a fire or electric shock. Prior to installing the blower , check for blower for any shipping dama ge.
Service and Limited Warranty CFM Home Products warrants this product to be free from defects in materials and components for three (3) years from the da te of first purchase, provided that the product has been properly installed, opera ted and maintained in accordance with all a pplicable instructions.
An important point after buying a device Storageflex (F) - 2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Storageflex (F) - 2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Storageflex (F) - 2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Storageflex (F) - 2 you will learn all the available features of the product, as well as information on its operation. The information that you get Storageflex (F) - 2 will certainly help you make a decision on the purchase.
If you already are a holder of Storageflex (F) - 2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Storageflex (F) - 2.
However, one of the most important roles played by the user manual is to help in solving problems with Storageflex (F) - 2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Storageflex (F) - 2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
