Instruction/ maintenance manual of the product F144I Stoelting
Go to page of 37
Futura F144I OWNER'S MANUAL Manual No. 513608 April 2005.
.
Need Part s or Service? We stock the parts you need. Our Technicians are factory trained and are certified in the Stoelting Technicare program. Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ CALL Distributor: _________________________ Phone No.
.
This manual provides basic information about the freezer . Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail.
.
Safety Alert Symbol: This symbol Indicates danger , warning or caution. Attention is required in order to avoid serious personal injury . The message that follows the symbol contains important information about safety .
.
T ABLE OF CONTENTS SECTION 1 - SPECIFICA TIONS .................................................................................. 1 1.1 Description .......................................................................................................
Fig. Description Page 1 Model Futura F144I/SF144I Freezer .................................................................. 1 2 Specifications .................................................................................................... 1 3 W arning Label Locations .
1 1.1 DESCRIPTION The Stoelting Futura F144I and SF144I (with blender) countertop combination shake/softserve freezers are gravity fed. The freezers are equipped with fully automatic controls to provide uniform product.
2 1.2 SPECIFICATIONS MODEL FUTURA 144 COUNTERTOP COMBINATION SHAKE/SOFTSERVE GRAVITY FREEZER Dimensions: Freezer: 22" (56 cm) wide x 28" (72 cm) deep x 34.75" (88 cm) high Crated: 28" (71 cm) wide x 35 1/2" (89.4 cm) deep x 40.
3 SECTION 2 INSTALLATION INSTRUCTIONS 2.1 SAFETY PRECAUTIONS Do not attempt to operate the freezer until the safety precautions and operating instructions in this manual are read completely and are thoroughly understood. T ake notice of all warning labels on the freezer (Fig.
4 Fig. 4. Space and Ventilation Requirements 2.2 SHIPMENT AND TRANSIT The freezer has been assembled, operated and in- spected at the factory . Upon arrival at the final destina- tion, the complete freezer must be checked for any damage which may have occurred during transit.
5 Fig. 7. F144 with Floor Stand 2.4 FLOOR ST AND INST ALLA TION T o install the F144 on the floor st and, follow the step s outlined below . 1. Uncrate the floor stand and place in an upright posi tion. NOTE Detailed instructions are included with each floor stand.
6.
7 3.1 OPERA T OR'S SAFETY PRECAUTIONS SAFE OPERA TION IS NOT AN ACCIDENT ; Observe these rules: A. Know the freezer . Read and underst and the Operating Instructions. B. Notice all warning labels on the freezer . C. Wear proper clothing. A void loose fitting garments , and remove watches, rings or jewelry which could cause a serious accident.
8 B. Freezing Cylinder Off-On switch The Freezing Cylinder Off-On switches are two position toggle switches used to supply power to the left or right freezing cylinder control circuit. When the switch is in the OFF position, the refrigeration system and auger will not operate.
9 O. Menu Navigation Buttons The Menu Navigation Buttons allow the user to display information regarding the freezer's status of opera tion as well as adjust product consistency. Selection Button (SEL) The SEL button is not functional in the normal operation mode.
10 Figure 12. Sanitizing Hopper Figure 13. Spigot Opened and Solution Draining 3.4 FREEZE DOWN AND OPERA TION This section covers the recommended operating proce- dures to be followed for the safe operation of the freezer . A. Sanitize just prior to use.
11 G . After about 6 to 10 minutes the freezer will shut off and the "SERVE" message will display on the LCD panel. The product will be ready to serve. Freeze down time may be longer for some frozen diet dessert mixes. High ambient temperatures may extend freeze down time.
12 B. Place the FREEZING CYLINDER OFF-ON switch in the ON position and push the CLEAN switch to rotate the auger . Allow the mix to agitate in the freezer barrel until the mix has become a liquid, about 5 minutes. C. Drain the liquid mix by opening the spigot.
13 Figure 19. Auger Flight Wear and Front Auger Support Bushing Wear D. Place the FREEZING CYLINDER OFF-ON switch in the OFF position. T o disassemble the freezer , refer to the following steps : A. Remove the mix inlet regulator from the hopper by pulling straight up.
14 CAUTION Do not use any type of sharp object to remove O- rings. Using tools to remove O-rings may damage spigot and O-rings. 3.9 CLEANING THE FREEZER P ARTS Place all loose parts in a pan or container and take to the wash sink for cleaning. T o clean freezer parts refer to the following steps: A.
15 D. Screw the springs onto the studs in plastic flights. Springs must be screwed into the flights com pletely to provide compression (Fig. 25). CAUTION Do not place the mix inlet regulator into the hopper before inst alling the auger . Attempting to inst all the auger with mix inlet regulator in place will damage the mix inlet regulator .
16 3.12 ROUTINE CLEANING T o remove spilled or dried mix from the freezer exterior , simply wash in the direction of the finish with warm soapy water and wipe dry .
17 3. SANITIZING – After the machine has been cleaned and contains no milkstone, the machine is reassembled. Then a FDA approved sanitizing solution is run through the machine to kill bacteria.
18 D. QUARTERLY W ARNING High voltage will shock, burn or cause death. Turn off and lock out main power disconnect before servicing. Do not operate machine with cabinet panels removed. The air-cooled condenser is a copper tube and aluminum fin type. Condensing is totally dependent upon airflow.
19 3.14 EXTENDED STORAGE Refer to the following steps for storage of the freezer over any long period of shutdown time: A. T urn both FREEZING CYLINDER OFF-ON switches to the OFF position. B. Disconnect (unplug) from the electrical supply source. C. Clean thoroughly with a warm water detergent all parts that come in contact with the mix.
20.
21 SECTION 4 TROUBLESHOOTING 4.1 ERROR CODES The following error condition codes will display on the control panel when the freezer is experiencing a problem.
22 ERROR CONDITION CODE 07 If the control panel displays a Drive Motor Current error (Error Code 07), place the Freezing Cylinder Off-On Switch in the Off position, wait 10 seconds, and return the switch to the On position.
23 SECTION 4 TROUBLESHOOTING CHARTS M E L B O R P E S U A C E L B I S S O P Y D E M E R s e o d r e z e e r F . n u r t o n . f f o s i r e z e e r f o t r e w o P . 1 . d e p p i r t r o n w o l b f i t i u c r i c r o e s u F . 2 . ) n r u t t o n l l i w r e g u a ( p u - e z e e r F .
24 M E L B O R P E S U A C E L B I S S O P Y D E M E R s e o d t c u d o r P . e s n e p s i d t o n . r e p p o h n i x i m o N . 1 s i e b u t r o t a l u g e r t e l n i x i M . 2 . d e g g u l p d e d e e n r o t a l u g e r t e l n i x i m l a i c e p S .
25 SECTION 5 REPLACEMENT PARTS 5 . 1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A . Model number of equipment. B . Serial number of model, stamped on nameplate.
26 Item No. Part No. Description Qt y . 1 2183047 Front Door Only 1 2177072 1.5" S pigot Extension 2177073 2.5" S pigot Extension 2177074 3" S pigot Extension 2 482019 Circular Door Kno.
W ARRANTY SOFT SER VE / SHAKE FREEZERS 1. Scope: Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and a.
An important point after buying a device Stoelting F144I (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stoelting F144I yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stoelting F144I - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stoelting F144I you will learn all the available features of the product, as well as information on its operation. The information that you get Stoelting F144I will certainly help you make a decision on the purchase.
If you already are a holder of Stoelting F144I, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stoelting F144I.
However, one of the most important roles played by the user manual is to help in solving problems with Stoelting F144I. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stoelting F144I along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
