Instruction/ maintenance manual of the product SILEX 40-G Stiga
Go to page of 10
STIGA Silex 40-G Silex 40R-G Silex 50-G Silex 50-H Silex 50R-B 8214-221 1-80 BRUKSANVISNING KÄYTTÖOHJEET BRUGSANVISNING BRUKSANVISNING GEBRAUCHSANWEISUNG INSTRUCTIONS FOR USE MODE D’EMPLOI GEBRUIK.
2 AB C D F G KL O RK L MN E J ST P H Q U W R S T Q U V X 1 2 3.
3 AB C D E G 1 2 3 4 4 6 8 5 7.
40 ENGLISH GB 1 SYMBOLS The following symbols can be found on the rotary cultivator/in these instructions. These will provide a reminder of the care and attention that is required during operation. If any symbol is missing, has been damaged or is illegi ble, it must immediately be replaced with a new one.
41 ENGLISH GB • The carbon monoxide in the engine's exhaust fumes is poisonous and can cause death. • W ear tightly fitting clothes and heavy-duty shoes which completely cover the feet. • The tank should only be half full when operat- ing on slopes.
42 ENGLISH GB 3.4 Throttle control Install the throttle on the left handle according to fig. 6. 3.5 Throttle cable 1. Install the throttle cable on the engine if not al- ready installed. See th e engine supplier ’ s man- ual. 2. Pull up the cable under the support’ s (4:U) up- per section over the screw (5:C).
43 ENGLISH GB 4.9 Handle height adjustment (1:G) Slacken off the knobs and set the handle to a com- fortable height. Then retighten the knobs again. 4.10 Oil filling/draining Always check the oil level before start- ing the engine. Plug for oil filler and checking the oil level.
44 ENGLISH GB 5 OPERATION 5.1 Fuel Read and understand all safety instruc- tions. No fires or smoking near to petrol. Use 92-95 octane lead free petrol. Oil-mixed petrol designed for 2-stroke engines must never be used. Filling Read and understand all safety instruc- tions.
45 ENGLISH GB 6 STORAGE Store the rotary cultivator in a dry place. Also see section “Safety instructions”. After draining the petrol, start the engine and allow it to run until it runs out of petrol. 7 MAINTENANCE W ARNING!Repairs must be carried out by the dealer .
46 ENGLISH GB 7.4 Changing the oil Change the oil the first time after 2 hours of oper- ation, and subsequently every 25 hours of opera- tion or at least once a season. Change oil when the engine is warm. The engine oil may be very hot if it is drained off directly after the engine is shut off.
An important point after buying a device Stiga SILEX 40-G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stiga SILEX 40-G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stiga SILEX 40-G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stiga SILEX 40-G you will learn all the available features of the product, as well as information on its operation. The information that you get Stiga SILEX 40-G will certainly help you make a decision on the purchase.
If you already are a holder of Stiga SILEX 40-G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stiga SILEX 40-G.
However, one of the most important roles played by the user manual is to help in solving problems with Stiga SILEX 40-G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stiga SILEX 40-G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
