Instruction/ maintenance manual of the product MDRC-2124 Barco
Go to page of 48
MDRC-2124 User manual.
2.
3 Copyright notice This document is copyrighted. A ll rights are reserved. Nor this document, nor any part of it, may be reproduced or copie d in any form or by any means - graphical, elec tronic, or mechanical including photocopying, taping or informatio n stora ge and retrieval systems - without written permission of Barco © 2010 Barco N.
4 Table of Contents Table of Contents ....................................................................................... 4 Preface ........................................................................................................ 5 Important notice .
5 Preface Important notice Notice Although every attempt has been ma de to achieve techn ical accuracy in this document, we assume no resp on sibility for errors that may be found. Our goal is to provide you with the most accurate and usable documentation possible; if you discover errors, p lease let us know.
6 Environmental information Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local ordinances or regulations . This equipment has required the extraction and use of natural resources for its production.
7 Safety Instructions General Recommendations • Read the safety and operatin g instructions before operating the display. • Retain safety and operating instructions for future refe rence. • Adhere to all warnings on the display and in the opera ting instructions manual.
8 Intended use This display is an AMLCD display designed for viewing medical X-ray images. This unit should not be used near patients and should be kept outside of 1.83 m perimeter and 2.29 m v ertical. Power connection For use only with power supply SINPRO:HPU100-108 Input ： 100-240V~, 47-63Hz, 1.
9 Equipment not complying with IE C 60601 must be kept outside the patient environment, as defined in the sta ndard as at least 1.5 meters from the patient or the patient support.
10 Recommendations for usin g your display system 1. Optimize the lifetime of your display Enabling the Display Power Management System (DPMS) of your display (in the display’s Settings menu) will opti mize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time.
11 perform ance of the product . To ensure optimal product quality, Ba rco applies strict selection cr iteria for its LCD panels. To learn more about LCD technology and missing pixels, consult the dedicated white paper available at www.barcomedical.com.
12 Cosmetics and oils on the skin are both detrimental to the screen and difficult to remove. • Allow the display to war m up to room temperature be fore turning it on. Avoid sudden temperature changes in the environment, as this may cause condensation, which damages the display.
13 Cleaning the display Observe the following guidelines to maintain display and LCD screen. • Use a clean, lint-free, absorben t cotton cloth to clear off any residual glue from removal of the protective film or to remove surface dust. Apply light pressure to remove the dust.
14 Explanation of symbols DISPOSAL. Do not use hous ehold or municipal waste collection services for disposal of e lectrical and electronic equipment. EU countries require the use of separate recycling collect ion services. CAUTION. Read the acco mpanying text ca refully for proper operation and maintenance of the display system.
15 Introduction About the product Thank you for choosing Barco. The MDRC-2124 is an LCD display with an active matrix, thin-film transistor (TFT) liquid crys tal display (LCD).
16 Package overview User manual USA Power Cord EUR Power Cord China Power Cord DisplayPort Signal Cable DVI-D Signal Cable Power Adapter.
17 Display parts, controls and connections Front View Power LED 1. Green indicates the display is turned on. 2. Orange indicates the display is in stand-by mode.
18 Back View Control wheel 1. Press the contr ol wheel for 1 sec to power o ff to the LCD Display. 2. Swivel the control wheel for OSD menu. DisplayPort i nput DVI-I input USB upstream USB downstream DC Power input Kensington Security Slot The display can be secured to your desk or any other fixed object with Kensington lock secu rity products.
19 Installation Connecting the display Use only the power adapter, power cord , and the video cables shipped with this display. To setup this display, please refer to the following figure and procedures.
20 Note: To ensure the LCD Display will work we ll with your comp uter, please configure the display mode of your graphics ca rd to make it less than or equal to the na tive resolution, and make su re the timing of the display mode is compatible with the LCD screen.
21 Adjusting the display position Vertical height Portrait/Landscape Left to right pan Front to back tilt Remove display from stand.
22 On-Screen Display menus How to use the OSD menus 1. When the display is on and the OSD in not on the screen, press the control wheel. The front illumination is swit ched on for about 10 seconds. 2. To display the main menu , swivel the control wheel while the illumination is on.
23 6. To change an adjustment value or setting , swivel the control wheel to select the adjustment or setting. Next, press the control wheel to go in to edit mode. This is indicated by the trackbar turning dashed. Swivel the control wheel to change the value.
24 Adjustments menu Name Description Luminance Allows to manually adjust th e luminance target if you’d experience the overall image is too dark or too bright. When you change this setting, the display will adjust it s backlight to re ach its target.
25 Name Description Gamma 1.8 Gamma 2.2 Select one of these gamma options in case the display replaces a CRT display with a gamma of 1.8 or 2.2 respectively. sRGB Select this gamma op tion for viewing images intended for the internet. QAWeb Select this option if y ou wish to use the gamma settings defined in QAWeb Agent.
26 User submenu Name Description Red Allows to manually adjust the image red level target. Green Allows to manually adjust the image green level target.
27 Name Description Horizontal Position Allows to manually ad just th e horizontal position of the DVI analog image. Vertical Position Allows to manually adjust the vertical position of the DVI analog image. Level submenu Name Description Contrast Allows to man ually adjust the image contrast target of the DVI analog image.
28 Name Description LED Allows to switch the powe r LED’s on state on/off. The LED’s orange DPMS state is not influenced by this setting . So, when the display goes into power saving mode, the LED will turn orange, even if it was switched off by this setting.
29 Information menu Name Description Display Name Indicates the display type. FW Version Indicates the current interna l firmware version. Serial Nr Indicates the display serial number. Backlight Runtime Indicates the total time the display has been operating, excluding the time in stand-by.
30 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following troubleshooting. If the pr oble m persists, please contact your local dealer or our service center.
31 Problem: Image is scrolling • Check and make sure the video si gnal cable (or adapter) is well connected. • Check and reconfigure the display mode of the vertical refr esh rate of your graphics card to make it compatible with t he LCD Display. Problem: Vague image (characters and graphics) • Use “Clock” to make an adjustment.
32 Product dimensions.
33 Technical specifications LCD Panel Technology TFT Color LCD (E-IPS) Native resolution 1920x1200 Active screen diagonal 24.1" (611 mm) Active screen area 518 x 324 mm Pixel Pitch 0.
34 OSD languages English, French, German, Spanish, Italian, Dutch, Simplified Chines e, Traditional Chinese, Korean, Japan ese. Options Protective Cover Yes Touch Screen Yes Landscape/Portrait Yes App.
35 Compatibility modes Standard Resoluti on Vertical Refresh (Hz) Horizontal Scan (kHz) IBM VGA 640x480 60 31.5 VESA VGA 800x600 60 37.9 VESA XGA 1024x 768 60 48.4 VESA XGA 1152x870 60 54.36 VESA SXGA 1280x1024 60 63.96 UXGA 1600x1200 1920x1080 1920x1200 60 60 60 75 70.
36 Regulatory Compliance Canada, European Union, United States This display has been tested and found to comply with IEC/UL/EN 60601-1 and IEC 60601-1-2 standards, and is certified to meet medical standard UL 60601-1 and CAN/CSA C22.
37 The display was classified as requir ed by the MDD according to Annex IX of the directive and the medica l device (MEDDEV) guidance available at the time of classification.
38 EU EMC Directive 89/336/EEC EU Electromagnetic Compatibility Directive EN 60601-1-2 (2001) Collateral standard electromagnetic Medical Electrical Equipmen t compatibility requirements EN 55011 (Cla.
39 IEC 61000-4-6 Conducted immunity IEC 61000-4-8 Magnetic field immunity Conformance to the Medical Device Directive 93/42/EEC EN 60601-1 Medical Part 1 Genera l requirements for safety Electrical Equipment. U.S. FCC Compliance Statement This device complies with Pa rt 15 of the FCC Rules.
40 • Connect the equipment into an outlet on a circuit differe nt from that to which the re ceiver is connected. • Consult the dealer or an exp erienced radio/TV technical for help.
41 BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 20 08 ARTICLE 1: PRODUCT WARRANTY Barco nv, Medical Im aging Division warrants th at the equipment will be free of defects in workmanship or mat erial for the warranty perio d or the specific period of a warranty extension program.
42 1.3 The Customer shal l return, freigh t prepaid, th e defe ctive equipment or subassemblies in its original packaging wi th the assi gned RMA nu mber for re pair to the Ba rco nv, MID Customer suppo rt centre (or an authorised service centre).
43 mal functioning of the ha rdware covered under this A greement. 2.4 Normal wear and tear, use under circumstances exceeding specifications, such as use in dusty environment or under excessive tempe.
44 iv. difference in color temperature as a result of not using all displays of a multi-head configuration at the same rate. v. LCD luminance uniformity that is in within the product specifications or luminance uniformity performance that is inherent to LCD technology.
45 version of the software. (c) The repair or replacement un der the Warra nties covers the cost of ma terial and l abor. ARTICLE 5: DISCLAIMER O F WARRANTIES BARCO NV, MID DISCLAI MS ALL WARRANTIES, EXPRESSED OR IMPLIE D, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FO R A PARTICULAR PURPOSE.
46.
47.
B410640-02 November 2010 Barco nv Medical Imaging President Kennedypark 35 B-8500 Kortrijk, Belgium www.barco.com.
An important point after buying a device Barco MDRC-2124 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Barco MDRC-2124 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Barco MDRC-2124 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Barco MDRC-2124 you will learn all the available features of the product, as well as information on its operation. The information that you get Barco MDRC-2124 will certainly help you make a decision on the purchase.
If you already are a holder of Barco MDRC-2124, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Barco MDRC-2124.
However, one of the most important roles played by the user manual is to help in solving problems with Barco MDRC-2124. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Barco MDRC-2124 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
