Instruction/ maintenance manual of the product MULTICLIP 48 Stiga
Go to page of 8
1 2 3 SVENSKA ............................... 1 SUOMI .................................... 7 DANSK ................................. 13 NORSK ................................. 19 DEUTSCH ............................ 25 ENGLISH ........................
H* K* S TO P G S TO P I 6 7 9 11 5 8 10 P R M G S S 14 16 18 12 15 17 19 13 « L » « R » T 40 Nm 40 Nm 20 L K S H 2 cm 2 1 D E J* ÖVRIGT NORDISK MILJÖMÄRKNING MUL TICLIP PRO 48 11-8396 MUL TICLIP PRO 51 S 11-8796 Denna maskin uppfyller kraven enligt Nordisk Milj ö m ä rkning av gr ä sklippare version 3.
ENGLISH GB GB SAFETY REGULA TIONS 1) Read the instructions carefully . Get familiar with the controls and pr oper use of the equip- ment. Learn how to stop the engine quickly . 2) Only use the lawnmower for the purpose for which it was designed, i.e. for cutting grass.
ENGLISH GB GB Regular maintenance is essential for safety and performance. 2) Never store the equipment with fuel in the tank inside a building where vapour may r each a flame or a spark or a source of extr eme heat. 3) Allow the engine to cool before storing in an enclosed space.
ENGLISH GB GB IMPORT ANT For the instructions relative to the engine and the battery , please read the relevant instruction handbooks. Equipment which is marked with an asterisk (*) comes as standard in certain models or countries. Certain models do not have throttle contr ol.
ENGLISH GB GB attempts at starting in order to pr event dis- char ging the battery . 6. For the best mowing results, the engine should always be driven at full throttle. STOPPING THE ENGINE The engine may be very warm immedi- ately after it is shut off.
ENGLISH GB GB LUBRICA TING DRIVE SHAFT (*) Once per season, the wedge on the drive shaft should be greased. Remove the wheel (wheel cap, screw and washer). Then r emove the circlip and washer so that the gear wheel can be removed from the shaft. Lubricate the wedge with universal grease.
ENGLISH GB GB Reinstall as illustrated. Tighten the screw pr operly . Tightening torque 40 Nm. When replacing the blade, the blade scr ew should also be replaced. SHARPENING THE BLADES Sharpening of the blades must be done by wet method grinding, using a whetstone or a grind- stone.
An important point after buying a device Stiga MULTICLIP 48 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stiga MULTICLIP 48 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stiga MULTICLIP 48 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stiga MULTICLIP 48 you will learn all the available features of the product, as well as information on its operation. The information that you get Stiga MULTICLIP 48 will certainly help you make a decision on the purchase.
If you already are a holder of Stiga MULTICLIP 48, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stiga MULTICLIP 48.
However, one of the most important roles played by the user manual is to help in solving problems with Stiga MULTICLIP 48. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stiga MULTICLIP 48 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
