Instruction/ maintenance manual of the product 1210CE Sterling Power Products
Go to page of 16
1210CE 1220CE 1230CE 1240CE 1250CE 2415CE 2425CE 3616CE S TERLING POWER PRODUCTS ADV ANCED POWER PRODUCTS MARINE, AUT OMOTIVE & INDUSTRIAL Instructions for the International Range Battery Char ger.
these switches divide the battery charger INST ALLA TION OF amp/hr into the battery bank size ( STERLING BA TTERY domestic bank ) e.g take a 25 amp charger CHARGER on a 200 amp hr battery bank = a ratio of 8 : 1 .
to one which is being used, preferably to the one with the heaviest work load. failure to do this will result in reduced performance of the product, How long will my batteries last? What is the best battery type? The good the bad and the ugly about batteries.
full traction these batteries come in check it in your car do not assume the either 2 volt cells or 6 volt cells, and boat duty cycle is the same. not only will last approx 5-10 years in heavy must you check the water level, check duty cycles ( as with all batteries they that with the charger or alternator on do require a little maintenance ).
the plates falls to the bottom of the battery , this will at some stage cause that battery cell to short out and cease to exist as a cell, this in effect causes the other cells to over charge, and as .
pack will give 50 amps at 12.6 volts = 630. this means that two chargers which on the shelf appear the same are other sterling in fact separated by 300%, it is there fore important to find the output .
W ir danken Ihnen für den Kauf eines sehr fortschrittlichen Hochleistungs-Lade- /Netzgerätes. Erklärung der Funktionsweise: Das von Ihnen erworbene Lade-/Netzgerät arbeitet mit einer doppelten Schaltnetztechnik .
Ladegerät. W ichtig ist jedoch, daß bei der Installation nur einer Batterie alle positiven Ausgänge miteinander verbunden werden, damit auch dieser Ausgang die Referenzspannung der Batterie erhält. Ansonsten schaltet das Lade-/Netzgerät sofort in die 2.
V orbereitung: Es ist nicht schwierig, das Lade-/Netzgeräte richtig einzubauen, wenn Sie folgende Installationsschritte beachten. Empfohlene W erkzeuge und Materialien: 10A, 15A & 20A – Geräte.
Das Sterling Lade-/Netzgerät muß unbedingt trocken installiert und betrieben werden. W ie jedes offene elektronische Gerät wird auch dieses durch Nässe zerstört.
2) Parametereinstellung Einstellung der richtigen Ladeschlußspannung: GEL- / versiegelte Batterien: Dieser Batterietyp darf nur bis zur maximalen Ladeschlußspannung von 14,4V/28,8V geladen werden. Der schwarze Schalter muß nach oben (2). Die obere LED wird grün leuchten.
Spezifikation: T echnik: Doppelte Schaltnetztechnik (advanced switch-mode) Leistung: 10A / 20A / 25A / 30A / 40A / 50A (je nach Ausführung) Eingangsspannung: 90-125 & 185-260V/AC, 40-400 Hz Ausga.
15 14.5 14 13.5 13 12.5 12 11.5 11 10.5 CHARGER VOLTS 14.4 V GEL/SEALED BATTERIES CHARGER VOLTS 14.4 V GEL/SEALED BATTERIES CHARGE CURRENT CHARGE CURRENT C H A R G E R % C U R R E N T C H A R G E R % C U R R E N T 100 50 0 100 50 0 TIME TIME EXTRA CHARGE FOR COVENTIONAL OR TRACTION BATTERIES AT 14.
3 Outputs/Ausgänge + + + _ 1 10V/230V/AC BA TTERY 1 + _ BA TTERY 2 + _ BA TTERY 3 + _ Rec. Fuse (max. Output +10A) Empf. Sicherung (max. Leistung +10A) L N Earth/ Erdung S TERLING CHARGER POWER/P ACK 3 Outputs/Ausgänge + + + _ 1 10V/230V/AC BA TTERY 1 + _ BA TTERY 2 + _ Rec.
KONTROLLE UND INFORMA TION IST ALLES! 1 x Amperestundenanzeige(Ah) / 4 x V olt anzeige / 4 x Ampereanzeige BA TTERIE - MANAGEMENT - CONTROLLER „PRO - DIGIT AL“ Merkmale und Funktionen * 4 x Spannu.
OPTIMALES BA TTERIELADEN MIT IHRER ST ANDARD- LICHTMASCHINE! BESSER GEHT’S NICHT . St andard-Lichtmaschinen sind schlechte Batterielader! Deshalb volle Kraf t für Ihre Batterien! DIGIT ALER HOCHLEI.
An important point after buying a device Sterling Power Products 1210CE (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Sterling Power Products 1210CE yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Sterling Power Products 1210CE - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Sterling Power Products 1210CE you will learn all the available features of the product, as well as information on its operation. The information that you get Sterling Power Products 1210CE will certainly help you make a decision on the purchase.
If you already are a holder of Sterling Power Products 1210CE, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Sterling Power Products 1210CE.
However, one of the most important roles played by the user manual is to help in solving problems with Sterling Power Products 1210CE. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Sterling Power Products 1210CE along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
