Instruction/ maintenance manual of the product HDX Barco
Go to page of 12
La m p H o u s e w i t h 2 . 5 k W l a mp Install ation manual For H DX se ries R9864130 R5905109/04 27/05/2014.
Barco nv , Events Noordlaan 5, B-8 520 Kuurne Phone: +32 56.36.82.11 Fax: +32 56.36.88.24 Support: www.barco.com/esupport Visit us at the web: www.barco.
Changes Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war- ranties or merchantability and fi tness for a particular purpose.
.
Tabl e of c ontent s T ABLE OF C ONTENTS 1 . L a m p H o u s e w i t h 2 . 5 k W l a m p .... ........ ...... ...... ...... ........ ...... ...... ...... ........ ...... ...... ...... 3 1 . 1 I n t r o d u c t i o n ................. .................
Tabl e of co ntent s 2 R5905109 LAMP HOUSE W ITH 2.5 KW LAMP 27/05/2014.
1. Lamp Hous e with 2.5 kW lamp 1. LAMP HOUSE WITH 2.5 KW LAMP Purpose of the Lamp House with 2.5 kW lamp The Lamp House w i th 2.5 kW lam p is exclusively designed for the Barco HDX series and can thus not be used on any other equip- ment. Overview • Introduction • Safety 1.
1. Lamp Hous e with 2.5 kW lamp C AUTION : Always wear a wrist band which is conn ected to the ground while handling the electrostatic dis- charge (ESD) sensitive parts.
2. Lamp a nd Lamp H ouse 2. LAMP AND LAMP HOUSE About this chapter This chapter describes how t o remove and install the complete Lamp House. Furthermore, instructions on how t o align the lamp to maximize the light output ar e given.
2. Lamp and Lam p House Image 2-2 5. T ake the Lamp House by its handles and pull it out of its com par tme nt. Image 2-3 Note: While star ting up the projector , the electr onics detect if a Lamp Hous e is installed. If no Lamp House is instal led, it is not possible to start up the projector.
2. Lamp a nd Lamp H ouse Image 2-4 2. P ush the Lamp Hous e forward until it sli des fully into t he projector . The positioning pins mu st match t he holes in the Lamp House. 3. S ecure the 3 captive screws on the Lamp Ho use. Image 2-5 4. Install the right projector cover .
2. Lamp and Lam p House Necessary t ools 7 mm open-end wrench How to realign the lamp in the Lamp House? 1. S witch off the pr oject o r . 2. L et the pr ojector cool down for at least 15 minutes before proceeding to the next step. Warning: The Lamp H ouse is very hot after operation.
An important point after buying a device Barco HDX (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Barco HDX yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Barco HDX - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Barco HDX you will learn all the available features of the product, as well as information on its operation. The information that you get Barco HDX will certainly help you make a decision on the purchase.
If you already are a holder of Barco HDX, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Barco HDX.
However, one of the most important roles played by the user manual is to help in solving problems with Barco HDX. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Barco HDX along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
