Instruction/ maintenance manual of the product K202HQL Acer
Go to page of 27
Acer LCD Monitor User's Guide.
Changes may be made peri odically to the infor mation in this publication without obligation to notify any person o f such revisions o r change s. Such chang es will be incorpo rated in new editions of this manual or supplementary documents and publ ications.
iii Special notes on LCD monitors The following are normal with the LCD monitor and do not indica te a proble m. • Due to the nature of the fluorescen t light, the screen may flicker during initial use. Turn off the power switch and then tu rn it on again to make sure the flicker disappears.
iv Accessibility Be sure that the power outlet you plug the po wer cord into is easily accessible and located as close to the equipment ope rator as possible. When you need to disconnec t power from the equipm ent, be sure to unplug the power cord from the electrical outlet.
v ampere rating of the equipment plugge d into the extension cord does not exceed the extension cord ampere rating. Also, make sure that th e total rating of all products plugg ed into the wall outlet d oes not exceed the fuse rating. • Do not overload a power outlet, strip or receptacle by plugging in too many devices.
vi Note: Adjust only those controls that are covered by the operating instructions, since improper adju stment of other controls may result in damage and will often requ ire extensive work by a qualified technician to restore the pro duct to normal cond ition.
vii Disposal instructions Do not throw this electronic device into the trash when discarding. To minimize po llution and ensure utmo st protection of the global envi ronment, please recycle.
viii This product has been shipped enabled for power management: • Activate display’s Sleep mode with in 15 minutes of user inactivity. • Activate computer’s Sleep mode within 30 minutes of user inactivity. • Wake the computer fro m Sleep mode by pushing the powe r button.
ix Taking care of your vision Long viewing hou rs , wearing incorrect glasses or con tact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-contrast displays could stress your eyes. The follo wing sections provide su ggestions on how to reduce eyestrain.
Ac er Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi New Taipei City 221, Taiwan Declaration of Conformity We, Acer Incorporated 8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan Contact Person: Mr. RU Jan, e-mail:ru.jan@acer.com And, Acer Italy s.
Federal Communica tions Commission Declaration of Conformity This device co mp lies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device ma y not cause harmful in t erference, and (2) this device m u st accept any interfere nc e receiv e d, incl u ding interference that m ay cause undesired operation.
Special notes on LCD monitors iii Informati on for your safety and comfort iii Safety instructions iii Cleaning yo ur monitor iii Connecting /disconnec ting the device iii Accessibility iv Safe listen.
1 English Unpacking Please check that the following items are present when you unpack the box, and save the packing materials in case you need to ship or transport the monitor in the future.
2 Remove : Reverse the s teps to rem ove the ba se. English Screen position adjustment To optimize the viewing position, you can adjust the monitor tilt by using both of your hands to hold th e ed ges of the monitor as shown below. The monitor can be adjusted to 25 degrees up or 5 degrees down.
5 English Connecting th e power cord • Check first to make sure that the pow er cord you use is the correct type required for your area. • The monitor has a universal power supply that allows operation in either 100/120 V AC or 220/240 V AC voltage area.
6 English Connector pin assignment 15-pin color display signal cable PIN No. Description PIN No. Description 1 Red 9 +5 V 2 Green 10 Logic ground 3 Blue 11 Moni tor ground 4 Monitor ground 12 DDC-seri.
7 English 24-pin color display signal cable * PIN No. Description PIN No. Description 1 TMDS data 2- 13 NC 2 TMDS data 2+ 14 +5 V power 3 TMDS data 2/4 shield 15 GND (return for +5 V hsync.
8 English Standard timing table Resolution 1 640 x 480 60 Hz 2 640 x 480 72 Hz 3 640 x 480 75 Hz 4 MAC 640 x 480 66.66 Hz 5 VESA 720 x 400 70 Hz 6 SVGA 800 x 600 56 Hz 7 SVGA 800 x 600 60 Hz 8 SVGA 800 x 600 72 Hz 9 SVGA 800 x 600 75 Hz 10 MAC 832 x 624 74.
9 English Installation To install the monitor on your host system, please follow the steps below: Steps 1 Connect the video cable a Make sure both the monitor and comp uter are switched off. b Connect th e VGA video cable to the c omputer . c Connect the digital cabl e (only for dua l-input mode ls).
E N-13 USER CON T ROLS P o w e r Sw i t c h / P ow e r L E D: T o t u rn t h e m o n it o r O N o r OFF. Li g hts u p t o i n d i cate th e po w e r is t u r ne d O N. Us ing the Sho rtcut Menu P r e ss t h e fu n ct i o n bu tto n t o op e n t h e s ho rtcut me n u .
E N-14 Ma in Menu i con Sub Menu i c on S ub M enu it em D e scr i p ti on N / A U ser m ode U s e r d e f i n e d . Se tt i n g s c a n b e f i n e -t un e d to s u i t an y s i t u a t i on N / A N /A St a nd a rd m ode D efa u l t Set ti ng .
E N-15 Adjusting the OSD se ttings - - - - - - -- - - - - - -- - - - - - - - -- - - - - - -- - - - - - -- - - - - - -- - - - - - - - -- - - - - - -- - - - - - -- Note: The following content is for general reference only. Actual product specifications may vary.
E N-16 Adju s ting t he OSD po s it i on 1 Press the M ENU key to bring up the OSD. 2 Using the directional keys, select OSD from the on screen display.
E N-17 Adjusting the se t ting 1 Press the M ENU key to bring up the OSD. 2 Using the / keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. 3 The Setting menu can be used to adjust the screen Menu Language and other important settings.
E N-18 P roduc t inform a t ion 1 Press the M ENU key to bring up the OSD. 2 Using the / keys, select Information from the OSD. Then the basic information of LCD monitor will show up for current input.
1 5 English Troubleshooting Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if y ou can self-diagnose the problem. VGA mode Problem LED status Remedy No picture visible Blue Using the OSD, adjust brightness and contrast to maximum or reset to their default settings.
1 6 English DVI mode Proble m LED status Remedy No picture visible Blue Using th e OSD, adjust brightness and contra st to max imum or reset to their default settings. Off Check the power switch. Check if the AC power cord is properly connected to the monitor.
An important point after buying a device Acer K202HQL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Acer K202HQL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Acer K202HQL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Acer K202HQL you will learn all the available features of the product, as well as information on its operation. The information that you get Acer K202HQL will certainly help you make a decision on the purchase.
If you already are a holder of Acer K202HQL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Acer K202HQL.
However, one of the most important roles played by the user manual is to help in solving problems with Acer K202HQL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Acer K202HQL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
