Instruction/ maintenance manual of the product Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner N Star Trac
Go to page of 20
V-bike ® Spinner ® Spinner® Pro Spinner® Elite Spinner® NXT O WNER ’ S G UIDE.
Page 2 STAR TRAC GROUP CYCLES OWNER’S GUIDE T ABLE OF C ONTENTS _ Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions .
Page 3 STAR TRAC GROUP CYCLES OWNER’S GUIDE S AFETY I NSTRUCTIONS _ I NSTRUCTIONS The following fitness safeguards and operating precautions a re dir ected to purch asers and users of STAR TRAC group cycles. Club Managers should ensure that members and fitness staff are trained to follow these same instructions.
Page 4 STAR TRAC GROUP CYCLES OWNER’S GUIDE A SSEMBLY AND S ETUP _ A SSEMBLY AND S ETUP V-BIKE ® SPINNER ® ASSEMBLY AND SETUP Use the following procedures to unpack and assemble your STAR TRAC V-BIKE SPINNER . U NPACKING Position the shipping carton so the “Heav y E nd” logo is located at the bottom.
Page 5 STAR TRAC GROUP CYCLES OWNER’S GUIDE ASSEMBLY 1. Install th e Back Leg Place the back le g in position at the re ar of the cycle, aligning the two holes in the leg with the mati ng holes in the fram e bracket. Insert two 8mm x 70mm bolts through the frame bracket and back leg, and install a flat w asher and nut on each bolt.
Page 6 STAR TRAC GROUP CYCLES OWNER’S GUIDE 5. Install the Handlebar Insert the handlebar post into the frame assembly and secure in place using a tension handle. Position the handlebar on top of the handlebar post and secure in pl ace using a tension handle and washer.
Page 7 STAR TRAC GROUP CYCLES OWNER’S GUIDE SPINNER ® PRO / ELITE / NXT ASSEMBLY AND SETUP Use the following procedures to unpack and assemble your STAR TRAC SPINNER ® . U NPACKING Prepare the area that you will b e unpacking and as sembling the bi ke to be free from debris that may cause damage.
Page 8 STAR TRAC GROUP CYCLES OWNER’S GUIDE Take time now to enter your V-bike ® Spinner ® serial num ber in the space below (s erial number is located on the bottom cross member). If parts are missing, or if you have any operational questions, please ca ll Star Trac’s Serv ice department at (800) 50 3- 1221; have your serial number ready.
Page 9 STAR TRAC GROUP CYCLES OWNER’S GUIDE ASSEMBLY Following these steps in order will m inimize the build tim e and ensure proper assem bly. Note: Not all of the following pr ocedures are performed on all models; Spinner ® Pro, Elite and N XT.
Page 10 STAR TRAC GROUP CYCLES OWNER’S GUIDE Pro & Elite Only Using the 5mm hex wren ch and a 13mm comb ination wrench insert 2- M10X55mm flat head screws, nuts and washers to secure the front leg as sembly to the fram e.
Page 11 STAR TRAC GROUP CYCLES OWNER’S GUIDE 5. Install the Handlebar NXT Only Positioning the handlebar post with the number 1 on top and insert the handlebar into the handlebar sleeve locking it at number 4. Slide the handlebar onto the handlebar post insert with the water bo ttle holders facing forward and align the three screw holes .
Page 12 STAR TRAC GROUP CYCLES OWNER’S GUIDE You have now completed the assembly of your STAR TRAC SPINNER ® PRO / ELITE / NXT S PINNER PR O SPINN ER ELITE SPINNER NXT Testing the Bike Use this checkli st to perform the b ike test procedu re.
Page 13 STAR TRAC GROUP CYCLES OWNER’S GUIDE I NSTRUCTIONS FOR U SE _ Your STAR TRAC group cycle is easy to use. Simply sit on the cy cle, tighten the pedal straps a nd begin pedaling. The cycle allo ws the user full control over resis tance by simply adjus ting the brake p a d.
Page 14 STAR TRAC GROUP CYCLES OWNER’S GUIDE HANDLEBAR ADJUSTMENTS Proper position for the hand lebar is based primaril y on comfort. Typica lly, the hand lebar should be positioned slightly higher than the seat. All group cycles allow for adjustment of handlebar height.
Page 15 STAR TRAC GROUP CYCLES OWNER’S GUIDE SMART RELEASE™ SYSTEM (Spinner ® Elite) Allows the benefits of the dir ect drive system with a safety clutch to release the crank from the di rect drive when a force is applied to t he pedals.
Page 16 STAR TRAC GROUP CYCLES OWNER’S GUIDE M AINTENANCE _ This section provides th e procedures to ma intain the group cycles in service able condition.
Page 17 STAR TRAC GROUP CYCLES OWNER’S GUIDE Inspection / Adjustment Inspect major moving parts that require cons tant proper torque. Loose or misadjusted pa rts can result in personal injur y or dam age to the cycle. Check the following parts for security and/or proper torque.
Page 18 STAR TRAC GROUP CYCLES OWNER’S GUIDE Drive Chain Lubrication The drive chain will require lubri cation once a month, or after ev ery 100 hours of use. Th e chain should be lubricated with a l ight oil (preferably a lubricant that com es with a spray hose th at fits in front of the can) and a dry clean towel.
Page 19 STAR TRAC GROUP CYCLES OWNER’S GUIDE 3. Tighten the two bolts th at go through th e frame, moving the flywheel forward by turning clockw ise, until there is a pproximately 3/16” of slack in the chain (Diagram B). 4. Re-tighten the two bolts on the sides of the fl ywheel and replace th e chain shrouding.
STAR TRAC 14410 Myford Road Irvine, California 92606 Telephone: (800) 228-6635, (714 ) 669-1660 Fax: (714) 508-3303 http://www.startrac.com Part Number 620-7302, Rev.
An important point after buying a device Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT you will learn all the available features of the product, as well as information on its operation. The information that you get Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT will certainly help you make a decision on the purchase.
If you already are a holder of Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT.
However, one of the most important roles played by the user manual is to help in solving problems with Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Star Trac Spinner, Spinner Pro, Spinner Elite, Spinner NXT V-bike Spinner Spinner Pro Spinner Elite Spinner NXT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center