Instruction/ maintenance manual of the product VF80 Stanley Black & Decker
Go to page of 16
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 07193 10/2014 V er . 5 USER MANUAL Safety , Operation and Maintenance VF80 HYDRAULIC VENTILA TING F AN.
.
VF80 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an authorized and certied dealer .
4 ► VF80 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
VF80 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► VF80 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
VF80 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► VF80 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
VF80 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► VF80 User Manual PRE-OPERA TION PROCEDURES PREP ARA TION FOR INITIAL USE The tool, as shipped, has no special unpacking or as- sembly requirements prior to usage. Inspection to as- sure the tool was not damaged in shipping and does not contain packing debris is all that is required.
VF80 User Manual ◄ 1 1 NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the OFF position when coupling or uncoupling hydrau- lic tools.
12 ► VF80 User Manual SYMPTOM CAUSE SOLUTION T ool does not run. Power unit not functioning. Check power unit for proper ow and pressure. 4–12 gpm/15–45 lpm at 500–2000 psi/35–140 bar . Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports.
VF80 User Manual ◄ 13 Capacity........................................................................................................................................ 1700 scfm/802 lsec Flow Range ....................................................
14 ► VF80 User Manual 29 30 16 14 13 15 12 29 29 21 26 11 24 23 29 19 20 18 17 25 8 10 3 31 4 2 1 6 7 5 9 28 27 22 33 32 VF80 P ARTS ILLUSTRA TION.
VF80 User Manual ◄ 15 ITEM P ART NO. QTY DESCRIPTION 1 06952 1 VOLUTE 2 33458 1 BLOWER WHEEL 3 14607 1 INLET SCREEN 4 06954 1 MOTOR MOUNT BRIDGE 5 06638 1 CAPSCREW 6 00429 1 NUT 7 00152 8 T APPING S.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker VF80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker VF80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker VF80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker VF80 you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker VF80 will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker VF80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker VF80.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker VF80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker VF80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
