Instruction/ maintenance manual of the product SK58 Stanley Black & Decker
Go to page of 22
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 70744 8/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance SK58 HYDRAULIC SINKER DRILL.
.
SK58 User Manual ◄ 3 SAFETY SYMBOLS .................................................................................................................................................. 4 SAFETY PRECAUTIONS .............................................
4 ► SK58 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
SK58 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re- view them carefully before operating the tool and before performing general maintenance or repairs.
6 ► SK58 User Manual 02754 SK58 Name T ag 03786 GPM Sticker SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
SK58 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► SK58 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
SK58 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► SK58 User Manual NOTE: If uncoupled hoses are left in the sun, pressure in- crease within the hoses may make them difcult to connect. When possible, connect the free ends of the hoses together . 5. Connect the hose from the air supply to the hose on the tool.
SK58 User Manual ◄ 1 1 8. After the rock bit has carved out a depression in the material being drilled, open the hydraulic valve le- ver fully . Readjust the motor control knob to obtain a good drilling speed. Adjust the air valve to ensure the cuttings are being extracted from the drill hole.
12 ► SK58 User Manual • Make sure all couplers are wiped clean before con- nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau- lic tools. Failure to do so may result in damage to the quick couples and cause overheating of the hy- draulic system.
SK58 User Manual ◄ 13 PROBLEM CAUSE REMEDY T ool does not run. Power unit not functioning. Check power unit for proper ow and pressure (7–9 gpm/26–34 lpm, 1500–2000 psi/105–140 bar . Couplers or hoses blocked. Remove restriction. Pressure and return line hoses reversed at ports.
14 ► SK58 User Manual ACCUMULA TOR CHARGING 1. Perform steps 1 through 4 of the accumulator test- ing procedure above. 2. Connect the chuck of the charging assembly to the charging valve on the accumulator tester or , if pre- ferred, remove the tester from the charging valve and connect the charging assembly chuck directly to the charging valve.
SK58 User Manual ◄ 15 Figure 2. Charging the Accumulator CHARGING THE ACCUMULA TOR.
16 ► SK58 User Manual Shank Size (SK581 10 Air , SK58120 W ater , SK58310 UW Air) .................................................... 4-1/4 in. × 1 in. Hex Shank Size (SK58130 Air) ..................................................................
SK58 User Manual ◄ 17 SK58 P ARTS ILLUSTRA TION.
18 ► SK58 User Manual ITEM P ART NO. QTY DESCRIPTION 1 04763 1 AIR TUBE (SK581 10/SK58130/SK58310 ONL Y) 04965 1 W A TER TUBE (SK58120 ONL Y) 2 07064 1 VENT PLUG 3 04964 2 HANDLE GRIP ASSEMBL Y 4 01.
SK58 User Manual ◄ 19 SK581 10 – 1 INCH × 4-1/4 HEX SHANK AIR SK58120 – 1 INCH × 4-1/4 HEX SHANK W A TER SK58130 – 7/8 INCH × 4-1/4 HEX SHANK AIR SK58310 – 1 INCH × 4-1/4 HEX SHANK AIR, UNDER- W A TER USE NOTE: USE P ART NUMBER AND P ART NAME WHEN OR- DERING.
20 ► SK58 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif- ferent depth operation.
SK58 User Manual ◄ 21 NOTES.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker SK58 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker SK58 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker SK58 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker SK58 you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker SK58 will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker SK58, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker SK58.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker SK58. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker SK58 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
