Instruction/ maintenance manual of the product RV06 Stanley Black & Decker
Go to page of 18
© 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 24056 9/2014 V er . 3 USER MANUAL Safety , Operation and Maintenance R V06 HYDRAULIC ROCKER V AL VE.
.
RV06 User Manual ◄ 3 SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hydraulic T ools recommends that servicing of hydraulic tools, other than routine maintenance, must be performed by an au- thorized and certied dealer .
4 ► RV06 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel.
RV06 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual, and on the stickers and tags attached to or on the tool and hose(s). These safety precautions are for your safety . Review them carefully before operating the tool or performing any maintenance or repairs.
6 ► RV06 User Manual SAFETY T AG P/N 15875 (Shown smaller then actual size) DANGER DANGER READ OPERA TION MANUAL AND SAFETY INSTRUCTIONS FOR THIS TOOL BEFORE USING IT . USE ONL Y P ARTS AND REP AIR PROCEDURES APPROVED BY ST ANLEY AND DESCRIBED IN THE OPERA TION MANUAL.
RV06 User Manual ◄ 7 The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools.
8 ► RV06 User Manual Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bu.
RV06 User Manual ◄ 9 Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max.
10 ► RV06 User Manual PREOPERA TION PROCEDURES CONNECT HOSES 1. If the RV06 is to be used on or near electrical lines, both of the hoses used to connect the RV06 to the intensier must be labeled and certied non-con - ductive (see Hose Recommendations).
RV06 User Manual ◄ 1 1 OPERA TING PROCEDURES • Observe all safety precautions given in this manual. • Refer to the applicable manual for the tool connect- ed to the RV06. • Activate the parent circuit to provide power to the in- tensier . Pressure will now be available at the pres - sure port of the RV06.
12 ► RV06 User Manual NO TICE In addition to the Safety Precautions found in this manual, observe the following for equipment protection and care. • Make sure all critical tool markings, such as labels and warning decals, are securely in place and leg- ible.
RV06 User Manual ◄ 13 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the control valve, always check that the high-pressure hydraulic power source is supplying the correct hydraulic ow and pressure to the control valve.
14 ► RV06 User Manual Weight ................................................................................................................................................... 2.6 lb/1.18 kg Length...................................................
RV06 User Manual ◄ 15 R V06 P ARTS ILLUSTRA TION.
16 ► RV06 User Manual ITEM P ART NO. QTY DESCRIPTION 1 05338 1 BODY 2 12838 1 PIPE COUPLING 1/4 NPT 3 23128 2 HOSE ASSY 4 05337 1 NIPPLE 5 15399 1 BACK-UP RING 6 00018 1 O-RING 7/16 × 9/16 × 1/16 .
.
Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com.
An important point after buying a device Stanley Black & Decker RV06 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Stanley Black & Decker RV06 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Stanley Black & Decker RV06 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Stanley Black & Decker RV06 you will learn all the available features of the product, as well as information on its operation. The information that you get Stanley Black & Decker RV06 will certainly help you make a decision on the purchase.
If you already are a holder of Stanley Black & Decker RV06, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Stanley Black & Decker RV06.
However, one of the most important roles played by the user manual is to help in solving problems with Stanley Black & Decker RV06. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Stanley Black & Decker RV06 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
